Moped fork insolation

Awesome video from a fellow racer. Guess I’ll drop the money on the oem clutch pack

I bought the rekluse torque core manual drive clutch and I have noticed that it does not want to disengage. I have to pull the clutch lever all the way in for it to disengage the gears. Same thing It doesn't want to start in gear. Im wondering if I need to up my change the position from 1 to 2 on my pressure plate

hello. is this PP or PE?

Nothing like washing out the oil and washing out the dirt in continously dirty solution. Ridiculous.

hey man, mind sharing the results? i'm having the same issue.

Ever had any issues packing them full on a dirtbike? They get pretty stiff when you fill them.

So great thank you 🙏

I had exact same experience with oem vs tusk clutch in my 2012 ktm 300 xc-w

Great tip man, go to do mine this way to.👍

Honestly,. Did this holdup long term.?

Thanks So much for this video, I just pulled the rear wheel on a dirt bike for the first time, Followed your instructions exactly. When I got into the bearing race it was a filthy dirty, black and grinding like sand! I flushed all that mess out with WD-40, a tiny brush, and air hose till shiny like new, then packed and rotated with proper WP grease. Bearings are like new again! Thanks for posting !

your video helped me charge my shorai, Thanks for taking the time to share this

If I had an ANNOYING neighbor pounding on drums, I'd have a word or two for him!

Filter the solvent through a paint strainer. It's a very fine strainer. $8 for 100 at harbor freight.

I have the same problem

did you use HDPE or LDPE?

Thanks for the share, do you cut your bars shorter for these races or do stock bars fit between the saplings and trees during the tight squeeze shots ?

excellent video. I have a new to me bike that may require tank repair. No one makes replacements.

Thanks for the info!

Thats awesome I have the same problem

Good video. Only thing I disagree with is the warm water idea... if the solvent didn't effect the glue the warm water will never do it.

So if they already wiggle a little are they already gone?

You lost me at Justin Bieber!!!!👎🏻

Thanks for posting. It worked for my Shorai motorcycle battery

That’s great! I’ve been doing that same process fir years also. It works great for me as well. Good stuff!

I've always wondered if diesel or kerosene would work the same for cleaning my foam filter. Would that even work?

where can i buy usa made bearings?

Is that 260 centigrade or Fahrenheit.

I like you ways because some time spencers thing is bla bla bla

Колхозник...

I have a 2021 crf450r. Less than 10 hours on it and my clucth is dragging and quite frankly, I'm pretty fuckin pissed off about it.

Well, do you have an update afterwards? Like after you installed the factory clutch

I can’t believe I have to say this but knowing gas is thinner than water and that your going to test it with soap and water and your gauge shows it holding pressure, doesn’t that make filling it with water pretty pointless? Just saying.

Dose it matter what oil you use

can you sand it down and smoothen it after! or you think that would compromise the weld?

Great video, thank you for taking the time to post this.

Too late for me as my Shorai is hooped. Their charger is not very smart so I will get an Imax charger and will be looking for a new lithium battery that has the battery management system installed in the battery. Thanks for the help.

That's some of the most expensive filter oil that you can possibly buy...... just saying.

You say not use hot water but you use hot air?

I take off the grips and switch and leave the wiring behind the number plate with tape over the connector. I don't like that they are fatter at all but get used to it eventually. If you run some type of hand Mitt covers, tusk makes some, you can really stay warm.

Put cases in the oven bearings in the freezer easy work

Same for Ballistic Batteries, and made my balance cable the exact same way

Cheers

Great review!! Thanks for sharing!!

Nice and creative Videos， This is really my favorite channel.:) .🌴🌴🌴excellent 👍👌👍👌👍 🌴🌴🌴 🌴🌴🌴 🌴🌴🌴 🌴🌴🌴 White Plains City Greene

I have a bone stock 2012 ktm 350 sxf. clutch drags

I’m not a racer i just ride my 2 stroke around like a bicycle sometimes may get up to speed rev it up and a couple weak wheelies even tear through hills and grass. But I don’t think that’s very hard riding. How often do you suggest cleaning and oiling the air filter?

What graphics are those

so looks like all plastic fuel tanks have polyethylene so i really should get a welding gun