It cost $360 US dollars. A good pulley, carabiner, and Prusik loop would be less than half that amount and be multi-functional. Even though you can climb with the Capto it really exists for replacing those three components in one package in my opinion. Is it worth the money? Ultimately yes, but you are buying a luxury item at the end of the day. If I were starting out building my equipment cache I would pass for more practical items to make my money go further. Also, the device is somewhat heavy. Something to consider if you are having to carry gear long distances. I think the correct market for this device are municipal rescue and fire departments that can haul the gear in trucks. Paired with a Clutch it's a nice combination.
@Ontopworld20115 күн бұрын
Hi Perry thank you for the video. Where did you get those pulleys from (link please) I never seen those in the UK. Cheers and thanks a million.
@perryfire30065 күн бұрын
Check this out:kzfaq.info/get/bejne/rNeFabGVu5fHo5c.html In short, look for arborists or rope rescue suppliers. Wesspur, Sherriltree, Hownot2 store, etc. Cheers
@David-Does9 күн бұрын
About the 8th video I’ve watched completely understood it with your one thank you 👍🏽👍🏽
@perryfire30068 күн бұрын
That larger rope helps with visualization. Thanks for watching and the support!
@punchtool292016 күн бұрын
I have a large dead tree laying between to hills and supported by a few smaller trees and its upper branches. I'd like to pull it over as it's very sketchy approaching with a chainsaw and down right dangerous. How would you approach this using snatch blocks or block and tackle? What kind of line should be used? The tree location will be hard to get any equipment in to do the pulling. What can be used to generate force? I believe using mechanical advantage is the way to go but I'm new to this and need some advice from a pro. Thank you.
@perryfire300616 күн бұрын
If the tree is snagged then I would educate myself on the dangers before I did anything. There are a lot of good videos on KZfaq showing how to safely drop a snagged tree. If you need to get a line high up then I have videos showing that and obviously on how to set up anchors as well as Mechanical Advantage systems. But I can't really recommend any technique without seeing the tree because I don't know the exact situation or the size of the tree. You'll have to make that decision for yourself. As far as rope and gear requirements they have to be strong enough for its intended purpose. Obviously gear an arborist would use is best but if the tree is small you might get away with cheaper components. Sorry but there is no easy answer on this as there are so many variables that I can't ascertain without seeing the tree.
@punchtool292013 күн бұрын
@@perryfire3006 Thank you for the advice and all the great videos.
@JasonWebb_36918 күн бұрын
I searched 'how to tie 2 pieces of rope together' and yours was the 3rd video. The Double Fishermans works for perfectly for my self defense weapon - a padlock on a string. Thanks!
@perryfire300618 күн бұрын
Happy to have helped. Cheers
@jacoblindahl320622 күн бұрын
Clear and to the point!
@perryfire300621 күн бұрын
People's time is valuable, no need for filler. Thanks for watching.
@wynandscholtz196923 күн бұрын
Option 3 (drop loop)is the best option since you have 6:1 mechanical advantage.
@perryfire300623 күн бұрын
The best option is always what the situation presents. That is a fancy way of saying your environment and equipment are going to determine your course of action, not what is best or most efficient necessarily. That is why it is so important to have several techniques learned so you can adapt on the fly especially in a rescue situation. Thanks for commenting.
@cre912724 күн бұрын
Good video. One thought; I feel like it would be better to put your “foot hold” ‘binder through the top hole in the ascender (so the rope is captured in the device by more than just the cam).
@perryfire300623 күн бұрын
Valid point. It also gives you a bit more gain as you climb. Good eye!
@glennreynolds96225 күн бұрын
It would be easier to tie the prusick first and BFK last OR use a dbbl fisherman
@perryfire300625 күн бұрын
I'm not dogmatic about any of this stuff except not getting hurt. Your idea could absolutely be a better idea for some. Lots of ways to accomplish the same goal so thanks for lending your perspective.
@drachenfeuer504226 күн бұрын
This guy is the Bob Ross voice of knot tying…..aaaaand put a couple little loops here and then the rabbit comes out of the hole…..there and how bout a couple stop knots and just relax and slip this new little noose idea over your head……
@perryfire300625 күн бұрын
Ha! Comments are always interesting so thanks for the chuckle.
@KnoxHarringtonTheVideoArtist26 күн бұрын
I like that release system. We just use prusiks
@perryfire300626 күн бұрын
That's the fun of this stuff, lots of ways to accomplish the same goal. Cheers
@theangrytruckerchannel35929 күн бұрын
This is the instructor everyone needs at their firehouse, very knowledgeable and knows how to deliver that knowledge to others. I know a lot of great guys that know how to do a lot of things but they don't understand how to communicate that to the newer guys, keep up the good work!
@perryfire300629 күн бұрын
Thanks so much! I try to keep the information simple and clean for retention. I spent several years teaching fire recruits which was rewarding. Cheers
@SeattleRingHunterАй бұрын
What brand / model is this tripod?
@perryfire3006Ай бұрын
Pretty sure it is an SMC. Cheers
@wynandscholtz196923 күн бұрын
Skedco Industrial Tri-Pod. Personally I found the Triskelion to be better.
@perryfire300623 күн бұрын
@@wynandscholtz1969 I think you are right. I borrowed the tripod for the day and I can't remember but it sure looks like a SkedCo. Thanks for the clarification.
@wynandscholtz196923 күн бұрын
@@perryfire3006 most welcome and enjoy your videos.👍
@arthurzaith9693Ай бұрын
How you release tension of this first prussik after use?
@perryfire3006Ай бұрын
You simply raise the load slightly to release tension on the Prusik and hold it open against the pulley. Takes two hands but fairly straight-forward.
@colindaniels2774Ай бұрын
Great video! Thanks! They didn't teach this in my Rope Technician class
@perryfire3006Ай бұрын
Thanks. It's a good skill to have in your back pocket as we won't always have extra equipment to fix problems for us.
@phyrakkun7768Ай бұрын
This here I can understand.
@perryfire3006Ай бұрын
That was my goal. Thanks for watching.
@OldNavajoTricksАй бұрын
Spot on for ny learning ability marra (listening to vid from other side of kitchen lol...
@perryfire3006Ай бұрын
Thanks for watching, or listening!
@cherylm2C6671Ай бұрын
Thank you for sharing your rigging lesson.
@perryfire3006Ай бұрын
Thank you for watching. Cheers
@cherylm2C6671Ай бұрын
@@perryfire3006 You mean PRACTICE! Good for you this weekend!
@RollingEasyАй бұрын
Can you show the less cumbersome version please. The same knot but you've got the choice of it being an immovable loop or a 'choker'.... Both with individual uses. Also much easier to tie with larger and stiffer ropes.
@perryfire3006Ай бұрын
Do you have a link to what you are referring? Not quite sure what you are asking. Thanks
@shawnmasters1424Ай бұрын
Nice video with some excellent explanations and system example. I how ever would run both line to myself for working and safety (redundancy) as the patient is already in the basket they have two line they are attached too so if one rope was to fail the other would take hold.
@perryfire3006Ай бұрын
Or you could add another tether to yourself from the master ring. It's up to the operator in what he feels comfortable hanging from as long as it doesn't impede operations. The videos I show are one way of doing things but there are many other acceptable ways of performing these tasks. There is no right or wrong per se, as long as everybody stays safe. Cheers
@talltomrich1Ай бұрын
3:1 is within the WLL of G rated gear even with 6 people pulling on it. (Or 2 with a 9:1) Assuming bomber anchors it still maintains a 10-1 safety factor. Testing with load cells is interesting because even after pulling all that tension on twin lines and adding a 180lb person load, the anchors still only saw about 2kn even at about 150 degrees. What’s more interesting, when we did a pickoff increasing the load to about 380lbs, the load cell only read about 2.4kn. The added weight had deviated the angle down. Static safety factors aside. Even a fall factor 2 from a 1kn load wouldn’t be enough to slip a single clutch or I’D let alone two. When done properly highlines are nothing to be afraid of and are a great tool. Love your videos btw.
@perryfire3006Ай бұрын
Your post reminds me of the great "Hownot2" channel, which I am sure you are familiar. It comes down to safety factors, doesn't it? In the fire service we were always under a 15:1 standard which still influences me today although I know just as you have pointed out we can easily and safely push that arbitrary boundary. I am also under the constraint that a lot of people that watch my videos are new to this kind of stuff and I want to make sure they stay in the safe zone until they become more experienced such as yourself. I love this kind of feedback so feel free to contribute again. Cheers
@talltomrich1Ай бұрын
@@perryfire3006 I am familiar with Hownot2 but his “super good enough” stuff is recreation oriented and my/our business is rescue/professional. What I appreciate about your videos is that you clearly demonstrate the fundamental knowledge and “rope theory” showing what can be done with minimal gear instead of selling the latest equipment. It amazes me how different tech rescue standards are. Even with adjacent mutual aid partners. My understanding is that NFPA currently holds a 10-1 SF. Our department follows that for the general/ops level personnel but is flexible at the technician level such as yourself. So I can definitely appreciate your constraint to stay in the safe zone to avoid the monkey see monkey do tendencies. In my area at least, the rescue and rope access industry seems to be moving away from static system safety factors and towards calculating the potential dynamic events, designing systems that can accommodate it safely and then making them redundant.
@petersplat6164Ай бұрын
I was drawn in by the title and hoping to see someone make a block and tackle. I am sorry to see that you didn't make anything, you just bought it and put it together.
@perryfire3006Ай бұрын
No, I didn't make the rope nor the pulleys or the carabiners. But there are people out there that do and hopefully you can find them in your search. Good luck.
@davidtelford4160Ай бұрын
You can always throw on two hand jammers instead of the slings 😊
@perryfire3006Ай бұрын
Improvise! Thanks for watching!
@050sniperАй бұрын
The Bonus one reminds me of a reef knots i learned from my dad who was in special forces said he used this knot a lot =)
@perryfire3006Ай бұрын
Good memories, thanks for watching.
@Rescue-mt7flАй бұрын
Very well done, however, this day and age, I can’t understand why we are still showing reliance on slow to build systems with the ability to have human error. Prusik knots and hand tied systems in many places, have been replaced by presewn and rigged systems. With a low angle litter harness, a harken winch and ropes with presewn loops, you can perform a low angle rescue with a fraction of the personnel and with zero need to tie a single knot.
@perryfire3006Ай бұрын
Well, it's not slow if one is competent in rope work, but point taken. Look at something like the CMC Clutch which takes the need to know raise/haul conversions away. It's very nice until you have to carry it 5 miles along with all of the other pre-sewn and clip-in ready equipment. It gets heavy very quickly. A winch is also quite heavy especially if one needs a power supply to work it. There is value in knowing how to do this stuff with minimal equipment but yeah, if you can access your victim from the roadside then bring on all of the toys! Love that stuff.
@Rescue-mt7flАй бұрын
@@perryfire3006 winches need no peer supply to operate and pre planned systems can eliminate a ton of the weight issues. There are other winch versions to choose from. Many back country hauling systems we use here are managed with ATV or by placing in the basket with the trail wheel that we will need to use if we have to haul them 5 miles. Just some thoughts.
@jimdension8074Ай бұрын
This video saved my ass on a construction site - I needed to get all my tools, tile saw, tile etc from a patio deck up to a second floor patio deck - maximum weight was 100# - I had to get creative on the support arm that the pully was attached to - it had to swing in order for me get my products to clear the handrail - could not have done it without this video - thx so much for your excellent presentations 👍
@perryfire3006Ай бұрын
This is why I make these videos. Thanks for sharing.
@chriskinlaw3949Ай бұрын
I'm a little confused. The only change you made when converting from a 4 to 1 to a 5 to 1 was the location of the rope grab. Since you didn't change anything else, wouldn't you still be using the exact same amount of pulling force in both scenarios to move that 15 pound weight?
@perryfire3006Ай бұрын
Check out this video: kzfaq.info/get/bejne/ZtKYasirq6-Uf6M.html And this one: kzfaq.info/get/bejne/abFghqthysqte3k.html Those two videos should answer your questions. Sometimes this stuff seems like magic but there are principles behind everything I show. And to be honest I did a poor job in the original video explaining exactly what you are asking. Cheers
@chriskinlaw3949Ай бұрын
@@perryfire3006 That answered my question perfectly. Thank you for taking the time!
@bikegtxcr2 ай бұрын
This is a good idea for tight places. Thanks
@perryfire30062 ай бұрын
For sure, thanks for watching.
@NoNotThatPaul2 ай бұрын
Maybe link the other videos in the description
@perryfire30062 ай бұрын
Good idea, thanks
@stephenwhite13722 ай бұрын
Thanks! Just what I was looking for!
@perryfire30062 ай бұрын
Glad to help
@chaseanderson91982 ай бұрын
Could you rig this in a way where a chair is substituted for the log and a person could raise himself and then brake down on descent?
@perryfire30062 ай бұрын
You could, but the Clutch would have to stay with the load (person in chair) in order for it to work. Imagine switching a single pulley and the Clutch in their respective positions. If you look at workers from the old days working on church steeples and the like they used a similar system for raising and lowering themselves although their equipment was fairly basic.
@chaseanderson91982 ай бұрын
@@perryfire3006 Do you think a 4:1 or 5:1 is enough to easily raise body weight? Does 5:1 literally translate to 1/5 of the weight? i.e. 200 lb can be lifted with 40 lbs of force? Do you have a video of something similar?
@perryfire30062 ай бұрын
Yeah, a 4 or 5 to 1 could easily be used to lift one’s weight. There is theoretical mechanical advantage and practical mechanical advantage. Even high quality pulleys will still have friction so we can’t use theoretical MA but we can get close with quality gear at around 90% efficiency. So do the math and add some additional force for friction. No I don’t have a video of raising myself with a pulley system. Plenty of others though of raising objects.
@chaseanderson91982 ай бұрын
do you have a video on how a person could ascend and descend under self power using an ascension tool and braking tool?
@perryfire30062 ай бұрын
I have a bunch of videos on how to climb rope. Check those out and see if they don't answer your questions. Cheers
@ronperrault81822 ай бұрын
I like this version.
@UserUser-ke4ti2 ай бұрын
Were you an iron worker ?
@perryfire30062 ай бұрын
Retired Firefighter
@santoshernandez21882 ай бұрын
Great info thanks
@perryfire30062 ай бұрын
Thank you
@23takumi882 ай бұрын
Thank you good information to add to my arsenal of youtube climbing Videos im years out of the gym scene and just want back on the mountains so im brushing up on some technical stuff and just going for it once im comfortable... And this video has given my mind some ease when it comes to reppeling safely and how to incorporate the other devices. Thanks again
@perryfire30062 ай бұрын
Good luck and happy exploring!
@alexeisenhardt92992 ай бұрын
I used to just run the rope down to the tree next to it so there would be more of an angle not pulling the anchor straight up and wrap it 2 times and tie a bowline as close as to the tree as possible. That’s what you do when you don’t know any better anyway lol. I like method 1 and 3. I will have to start doing that
@perryfire30062 ай бұрын
Oh yeah, a running bowline can work just fine as you've experienced. I like my anchors just a bit more secure though with no chance of slipping if I'm going to be hanging off of it. Good luck with the other techniques.
@seanrhone53062 ай бұрын
Something I've never understood, maybe you can answer. Let's say you're lifting a 1800lbs, using the 7:1 shown here. Do the blocks have to be rated for 1800lbs or less, since the advantage?
@perryfire30062 ай бұрын
The 1800lbs never weigh less than 1800lbs. The mechanical advantage only facilitates using less than 1800lbs to lift the weight. So yes, your equipment has to be rated for whatever you are lifting, even if your effort is less. Cheers
@raymondcava46692 ай бұрын
Thank you for posting, I’m starting to understand how this all works. I have no real application for all of this but it’s interesting to watch they see the mechanical advantage.
@perryfire30062 ай бұрын
Good. If you watch my whole series on MA it should make things much clearer as you will develop building block recognition and patterns. Thanks for watching!
@bowlineobama2 ай бұрын
I don't see 7:1. How are you adding the Tensions?
@perryfire30062 ай бұрын
On which example? What are you coming up with out of curiosity? I should probably do a followup video showing how it all adds up.
@alexeisenhardt92992 ай бұрын
Nice
@perryfire30062 ай бұрын
Thanks!
@CoderTronics2 ай бұрын
Great tutorial thanks
@perryfire30062 ай бұрын
Thank you for the feedback, happy you liked it.
@KevinBuck-jn9zp2 ай бұрын
Perry, wonderfully clear video! I do, however, have one suggestion. When you have your weight on the prussik(s)/ascender above the knot you are passing, and you take off the assisted breaking device, you are relying on just the ascender and prussik(s) to hold you. Friction hitches and mechanical devices like ascenders are not to be used alone to support your life without some type of fall arrestor device or system to back them up. The ascender could flip open, the prussik/friction hitch could come loose if pushed from the top or bottom, and then you could fall to your death. A simple solution in both of these circumstances is to tie a catastrophe knot a few inches below the knot you are passing (and below your bottom prussik when passing on an ascent), and clip this into your harness belay loop or hard points. An example would be a figure 8 on a bight or overhand on a bight or clove hitch. Then, if the ascendors or friction hitches fail when your ABD is out of the system and being moved over the knot you are passing, the furthest you can fall is to that catastrophe knot, and you will hang off it, saving your life. Overall, great video, but adding this addition would make it safer. Keep up the great videos, I think they are helping a lot of people!
@perryfire30062 ай бұрын
Check out this video that is up to professional standards in the rope access world: kzfaq.info/get/bejne/hsmglbRmua_IY30.html Your points are all valid as you can never be too careful. However, there are different standards of safety according to what you are doing. That is why I labeled the technique for sport rappels. All great points though, thank you for sharing. Cheers
@alexeisenhardt92992 ай бұрын
Thank you sir
@perryfire30062 ай бұрын
You are welcome, thanks for watching.
@neitzsche51502 ай бұрын
This is still one of the best demonstrations of the variations of the Alpine Butterfly knot on KZfaq. Excellent video.
@perryfire30062 ай бұрын
Such a nice compliment, thanks so much.
@cacher19632 ай бұрын
What bag are you using to carry your gear and how do you set it up? Thanks for the videos
@perryfire30062 ай бұрын
I use a tool bag for the most part. Sturdy with lots of storage and a lot cheaper than an official rope or gear bag. Gear is set up for a haul/lower operation per bag. I have two identical bags loaded fundamentally the same but with extra specialty hardware in one or the other. The two bags together contain enough stuff that there isn't much I can't do.
@Venom-nk8nd3 ай бұрын
Z🇵🇬
@kevinguzman65043 ай бұрын
Thanks for making this video! It really helped!
@perryfire30063 ай бұрын
Good. Happy to help.
@willpkay3 ай бұрын
This is great, please could you do a 7:1? I can't find a video anywhere!
@perryfire30063 ай бұрын
Sure. Just give me some time as I am currently quite busy.