Did you try .38 spl in it?

Nice video....very informative for me as a relatively new shooter. Here for the first time and just subscribed to your channel.

Hint for others ( 7:00-7:20)..... adding wire length to the CT's ( current transformers....the "doughnut")....is typically not a problem, just use same gauge or thicker wire. CT's work by measuring current such that any (very small) voltage drop affect by adding CT wires is of very little influence...... go for it.

The trigger safety keeps it from accidently going off when dropped. Obviously, SIG has issues with that.

White Jennifer Perez Donna Jones Shirley

Aim High! 💪

Of course hunting ammo will not penetrate. Thats no suprise. But the 308 Fmj did (like expected)

Here's a loading tip that may make the process a bit easier. Load each round only partway through the loading gate, then use each succeeding round to seat the previous round in the magazine tube. This way only the last round will have to be forced all the way in with finger pressure.

I suspect either your magazine tube or your end cap may be machined out of spec. A 0.490" diameter major thread will fit securely into a corresponding hole with a 0.422" minor diameter. This is assuming 16 threads per inch and a 60 degree sharp Vee thread. Your rifle appears to have some sort of rounded metric knuckle thread which may have been cut shallower, but I can't see how the manufacturer expects an end cap with a 0.490" male major thread to secure itself to the 0.480" female minor thread of the magazine tube, regardless of how it is shaped. The difference in diameter is only 0.01" and provides too little bite.

I understand the need for meter hot lead on the breaker to get power, voltage reading. But isn't that 'double tapping' and against code ( doubtful the breakers designed for two wires ) ??? I guess only other option is two new breakers for A and B phases.

Thanks bud! Just subbed

That is absolutely one of the DUMBEST things I’ve ever seen in the firearm world…and that’s saying something. You should be horse laughed off the range the second you pull out your tacticool shotgun with that monstrosity attached to it.

👍🌿

Great video, thanks! One question...where did you wire the power source for the bottom CT measuring the generator power?

Great video! Love my Trash Panda

Thats bad azz. I have the xten and love it. This would be an inexpensive way to get into 9mm.

The 300 Blackout was made to be canned up. Put a can on your 300 and add a H-3 buffer and it will change the recoil and no ear protection required.

Thank you it was very good but to fast for me

How is the noise. It looks similar to a Q Cherry Bomb. The Cherry Bomb can rattle your teeth when using it on a 5.56

I think I'll pass. Thanks for the videos though.

use round nose or flat nose, not pointed, those are for revolvers. I have the regular huckleberry not the Tac version, so far I like it a lot.

How far was the distance

Hornady makes a good 357 with a red rubber protrusion. Careful loading anything into a tube mag that could hit the primer of the round in front of it. Rare, but it happens.

To lower the brightness more than what the brightness bar offers, there’s an option call “backlight”. You can lower the brightness from there or increase it. It requires the first password 3368, then second password 5768

Just bought the same model. Glad they cam through for you.

What size wire did you use for powering the meters?

Your ring for your bolt is upside down

check out NC shooter supply...they load blue bullets for minor PF...i average 130PF out of my p320 and about 128 out of my G17, i buy 2-3k at a time and havent had a malfunction yet.

Dope video! Love the .410 Keep killing it🤘🏽

I didn't have any interest in getting a 410. Now that i've watched this video i definetly will not be getting a 410. Good video! I love the ks7!

Jesus. This has got to be the gayest gun ever. And how the hell is kel tec your favorite?

There is usually an o-ring that is located around the threads that helps to snug the cap.probably when the cap popped off the o-ring got lost.

Why u shaking

Kinda looks like they cut the threads with a bit too much clearance.

Is the FMJ actually a jacket or is it plated like Blazer?

I agree with you I've owned all 3 and the Glock is the more extreme grip angle.

Damn this was painful Bill O'Reilly We'll do it live" or "Fuck it, we'll do it live"

Put the braces back on. The ATF had their tail ends handed to them on this

I just got mine as well; you did very well, Thank you

The Duracell was dead after 4 hours.

How did the grip hold up on you guys? I had the the same fitment "issues" on my Hogue grip and it broke after 15 rounds! The installation went exactly how you two showed in the video. I'm concerned the same thing is going to happen when I receive my second one, and I'm not sure how to prevent that in case I did something wrong.

Nice job! but could we get the power for the monitors from sources other than the main circuit breaker panel ... like from the plugs on the wall?

Zsr ammo correct curious making sure this stuff is safe?

Thank you best info 😎✌🏻

One of the most under rated guns. I love mine far more than my Glock.

Thank you for the video. It helped a lot. Do you remember you had Error Code #3 with this problem? Mine is an exactly same model as yours and has the same problem now (water in it) with Error #3.

Well done video 👍 thanks

How do you fit the closure plate on your main panel?....seeing that the new meter panel alongside has 2 wire-tunnel projections placed right over the flange-face?

If you google it says lithium lasts way longer than Duracell in EVERY SINGLE device except a flashlight lol. But yeh energizer lithium is by far the best battery on the market.

Thank you for the video, does your factory back up camera work with the new unit?