That's some choppy foam whoever is spraying is putting out want me to come lay some glass for a decent video ? Lol

at first you say dyna lube cant freeze then you say it can

My XR7 wouldn't prime, jammed a pencil in the inlet valve and felt the stuck ball come loose. Works great.......thx

Our tip keeps falling out of the spare gun

You did it so your waisting the pump fluid. That little bottle will last a long time when you do it correctly.

Respect!

Wow impressive I’ve never seen a compact rig like this. How much does it cost?

I work on these all day long

Hi I'm mechanic for for shop I work on these all day do alot of people know how work on these cus I'm get these sent to me from all over the USA an sometime other countries and how much should I be makeing fixing these reators

Do you have a website?

Old video, but very fantastic instructions.

Just want to give kudos to your service techs. I had a problem with my Project Paintrr Plus and couldn’t figure out what it was. I called your troubleshooters and they walked me through the situation.Turns out that when I last cleaned it Zi lost the tiny spring from the inlet valve . They sent me a new spring and I was up and running again. Thanks guys! You’ve got my recommendations from now on.

NICE one Lionel... What a catch to start your day

Thank you for this

this boring video needs a timestamp.

No mask smh

Could you use regular paint with this?

Where can we buy this? i didn't see it on your website.

What kind of hose reels do you use?

No one mentions the water left in the hose?!

T6DH-A: (E04) Sensor Err. Hose

I need to know what song was being played at 1:25. I need to know.

❤❤🎉🎉❤🎉🎉❤🎉🎉❤❤🎉❤🎉🎉❤🎉❤❤🎉❤

step one, move out of the house.

What type of be be and spring take on my magum x7

Hi I got a hydraulic foam machine and I’m having some issues with it first the material is connected to the wrong side so could I clean the machine by flush it with Hydraulic to connect them in the right direction and I wonder if that problem will make me run Rich on my iso side with is my poly side because is cross connected

Great information!! I'm getting ready to paint house exterior.

Great video , do you know if it could be sprayed with a titan spray machine 3000 what tip would be

Cómo limpiar

How about make a video cleaning oil based paint.

These guys need to stick to making strollers..I don't understand why they tried to make it as hard as they possibly could for the user to use..it's a spray paint machine not a fn astronaut launcher. MAKE IT SIMPLE..not fn hold this button down for 3 secs then flip the switch off and on then wait precisely 5 secs and blow in it until you pass out.

I see the pros flicking wrist and not releasing..

What's the website of this product? Or the connect line ? To if i want to order it

Tamsak done fullpack po fullsupport slamat pasukli po

Do I need to leave the blue hose attached while it's not being used?

How much do these units run? Are they available in a 4x4 chassis?

We ARE THE LARGEST MANUFACTURER OF airless spray machine in China, please contact us if you need

We ARE THE LARGEST MANUFACTURER OF airless spray machine in China, please contact us if you need

x5

at 2:54 to 3.00 minutes

That just cost about $500.00 to do that

I am founder of new company specializes in airless painting machine.we would like to send for you painting machine to be tested please feed us back about the machine. If you like the machine we would appreciate to make special KZfaq video about it.

You got a video or some advice for when my A side heat starts climbing to the E-01 ranges only if my hose heat is turned on? It's definitely getting that hot because I'll cycle the chemical through until my heat drops back down to 120°F, and the block under my know gets really warm to the touch.

This dude is killing me. Spraying is an art. You, sir, do not have it. Stay tuned folks. I’m going to show the world how this is properly done and get rich doing it.

Hey man, we can’t seem to get our iso/poly to heat up, our poly stays at 227

For sale?

This may be a stupid question but... it said if you are quitting for the night and will resume spraying in the morning, you can leave the pump hose submerged in the paint as long as you are going to use within 2 days. If the hose is left submerged in the paint how do you cover paint to keep it from drying out in the bucket?

Do you know the original supplier in Canada so I can order some blades for this dispenser?

it is super light and moving around all the time!

I've been spraying about 7 years now and can never get a pattern that nice. I've tried different tips, thinning, different pressures the lot. Even after full services. I have a 495 pc pro.