Joey Colunga

Пікірлер

@juniordominguez7390 5 күн бұрын

Where did you purchase the dtf pro cleaner?

@nwambush 5 күн бұрын

I got it from dtgpro

@susanvincentyortiz1060 6 күн бұрын

Are you using cadlink software?

@nwambush 5 күн бұрын

Yes cadlink v10 not the new v11. Heard it does print colors more vibrant

@titosantana1824 6 күн бұрын

Do you have a link please ?

@nwambush 5 күн бұрын

a.co/d/26iFDfz

@titosantana1824 6 күн бұрын

Where do you get the correct size hose ?

@spincitycottoncandyconcess1828 6 күн бұрын

At 2.55 if you can not suck the fluid threw the waste tank how do you unclog this

@nwambush 5 күн бұрын

Have you try suck and push? There is a pump in there

@chayagoldklang5203 12 күн бұрын

Hi and thanks for all your amazing informative videos. While doing a printhead cleaning, the printer actually stopped, I didn't want to force close it, I left it overnight, and it was still the same....so I shut it off. Now it came up with error 00025. When I put on the printer, the printhead goes to the left, back to the right, returns towards the left and stops in the middle, with the error code 00025. Can you help me with that?

@nwambush 5 күн бұрын

Have you try to clean the clear timing belt that goes thru print head. Use rubbing alcohol

@aliciatutt2531 15 күн бұрын

Thanks for the video Joey. I bought my CISS a couple months ago and Im finally going to set it up. How has your printer and prints been since setting yours up?

@nwambush 5 күн бұрын

Works good. Had one clog but making a video on how I fixed it. Full tear down video.

@kristenpineda1836 21 күн бұрын

Where did you get the black fittings? Do you have a link? Great video! Thanks!!

@nwambush 21 күн бұрын

a.co/d/0ppanx6

@c-f-productionscom 21 күн бұрын

Did you take out the roller so that the film can go through and print 🖨.

@nwambush 21 күн бұрын

The front rollers do come out. Other wise they will drag thru your print.

@butterfliezhomegarden3098 21 күн бұрын

Hi thank you so much for making this video. My GY and PB leak at the front right corner. Do you have any videos on how to fix this? Thanks

@nwambush 21 күн бұрын

No videos. But bch printing makes insulation gasket where your damper hooks to your carriage. Can’t add a photo but they do it. It will be in my next video.

@debsdesigns 23 күн бұрын

If you have never used your waste tank and you use an outer waste tank do you still have to reset the waste tank chip?

@nwambush 23 күн бұрын

Yes you do.

@debsdesigns 23 күн бұрын

@@nwambush Okay thanks

@searching4knowledge703 24 күн бұрын

How is the DTF Pro ink ?

@nwambush 21 күн бұрын

I been using it for over a year love it. Colors come out great. Yes it does cost more but you get what you pay for.

@youshawheeler6636 25 күн бұрын

Thank you ordered my love it works great, now just trying to stop smearing on film

@nwambush 25 күн бұрын

Use the leveling blocks in my profile. I make them. Helps with the smearing so much.

@jaymend2 27 күн бұрын

Thank you for sharing this video and the link for the CISS. They were very helpful. Can you please tell me if you used a RIP software or if you did not to print the image at the end of your video?

@nwambush 21 күн бұрын

I use cadlink v10. There is setting I have used to make it print good. Cadlink made them standard now. Also I change it to high quality

@AngelaSeay-qn1np 28 күн бұрын

im so over this my printer ink is coming out the bottom i did everything you did

@nwambush 21 күн бұрын

Bottom? Like where from bottom?

@susanvortiz9411 Ай бұрын

I have a ciss machine that shakes it for you

@luisbacayon6313 Ай бұрын

Bro, is it still needs to shake the inks for this setup?

@nwambush Ай бұрын

Shaking is in good no matter what system you have. Cause it will make sure the ink does not separate.

@luisbacayon6313 Ай бұрын

Thank you Sir. How’s your machine, still running great even without shaking the printer/inks? What do you do?

@chara1440 Ай бұрын

I have flushed the print head and my white isn’t printing. I am trying everything as I don’t want to take my printhead apart completely. How long did you let the printhead solution sit in the dampers?

@nwambush Ай бұрын

I let it sit for five mins. I am going to make a video on full tear down soon. Mine is plug after we went on vacation can unclog it. Will keep you updated

@Ortzdav5 Ай бұрын

Greqt video thanks for this my white has been clogging as of late. Do you shake the ciss now rather then the printer? If so how often. Do you think dropping a ball bearing or 2 in the white tanks would help with stirring when they are shaken?

@nwambush Ай бұрын

No can contaminate the ink

@Ortzdav5 Ай бұрын

@@nwambush so you dont shake/stir the white ink at all?

@nwambush Ай бұрын

I move the ink around. Don’t shake too much to cause air bubbles in the ink.