How do you know how far away the chair is goig to be when you bundle?

sorry . it wasnt clear. could you make a drawing of the winding pattern?

how did you know how to group the wires to use up the right length? can i use regular paper and some epoxy?

Dear brother the wiring you have done is very good 51 coil core wiring but you have not shown from where to start pls can you show near sensor connection thanks

i have the same motor ,we enlarged the slightly the hole through the axle we removed the silicon from the wire and recovered it with heat shrink as its thinner than silicon now we have air craft grade 8 guage phase wires abd changed hall sensor wires to thinner and stronger type,the motor now runs on 84 volts with 150 amp controller

Hi, i have thumb throttle that have start idle voltage 1.33v and when full run 3.42v, is this ok voltage, is this throttle ok and will this throttle work fine with such voltage values?. Thanks 🙂

You didn't add any gasket sealer when you put the covers back on...?

whats the amps of battery?

Terrible sounds coming from my speakers here, wtf bro. Nwo got you bro, stop playing the victim and living the victim life.

Didn't get thing about this it was to fast

Hi, great video. I am replacing a Hall effect sensor (49E) on my e bike LCD Display / Thumb Throttle. The problem is that the Hall effect was badly welded and suddendly fell and currently do not know which cable color goes where (only one I know is that the middle cable goes in the midle). Am I risking to burn the display if I wrongly weld the other 2 cables or given the voltage could not be a problem in your opinion??

Hello my friend, thanks a lot for this video..according to you i fixed my hub motor..only video how to mount hall sensors without pcb board on the internet... well done bro

Hi nomber chaiye sensor lena h

good work i'm planning to make a handmade wind turbine i have a 72v 1500/3000w e bike wheel do i need to change the winding, scheme, etc. if there is a gorsel, I would be glad if you could share i will use it on a 24v battery system can you also recommend the charging unit

Hi, what gauge and type of wire did you use to replace the original ones?

48 v 1500 watt Spir ? Mm?

What gauge did you use for the phase?

I need a guy like you take my 3 - 48 volt Lectric XP's battery packs and convert it to 72 volts. 2 of the packs are about 10ah and other pack is about 15ah. Awesome video

Hi , I have motor bafang gear 750w so wich hall sensor to change

Okay… I have a 1000 watt that phase wires I want to upgrade.. What size wire? And what kind?

How many mah

Fast forward video with no explanation about what your doing seems pout. Looks like you took a bunch off random cells and rewrapped tg to all look the same. Odds are about zero the cells are similar in anything. My guess is it works for a while but soon becomes so unbalanced it’s not usable. I have experienced the same type of thing.

How many amp did it take to melt those small wires what where you running before then what size wire was the one that melted ???

Multi. Meter. Not multimitor

Kitny mAh ka cell use kiya ?

P r o m o s m

I was thinking about using the 16-22 size crimp on bullet connectors for my 6 hall sensor wires. Then I could just plug and unplug them. Do you think that is a good idea ?

Estaría mejor que se mostrará más claro y prartico mostrando todos los colores de cables, desde poquito más lejos para ver bien las condiciones, el jiro derecha, siquiera,para los que no somos muy tegnicos gracias

कॉन्टॅक्ट नंबर & what is cost ?

The 5 small "phase" wires are actually the hall sensor wiring, no reason to make them thicker gauge since they dont are not powering the motor. They are only for monitoring the motor position. No harm done by replacing these wires but better to just use the space for thicker phase wires (the 3 thicker wires)

Good video my Friend🙂🤝

This is a shit video. Only the music is worse.

48 volt 20 A if I convert it to 72 how many A the battery is it going to be

One question: Are all cells have the same amp? Does bms work with differnt amp of cells

Hello, are all your cells rated at the same capacity.. mAh?

Hello sir I want motor sir

Great job next job balance the wheel

Your a drug addict iPhone theft take down the channel you should be reported. I feel sorry for your mother Chan.

I know you !

Good posting and just a side note. These are 1/2hp motors but if you wire them for low speed…. You lose a decent amount of power. I plan on wiring for high speed and then some pulley arrangements will slow down my rpm. Thanks again.

Great video can you tell me what the amp capacity is thx

Great music

nice job

'a miracle'. A miracle indeed, with all that solder your are splattering over your windings...

Wonderful explanation it works grat!!!!!

Crap music ….spoils the show !

Music super bro

Hi how do i get the highest speed?

Please how many neodymium magnet i can insert of 36 pole of washing machine

Super Great job as it shed light on the color codes functions. As I understand it from other research; I can see that Blue =Hi Speed ; White = Low Speed; Orange =Neutral ; RED = Start Winding; Yellow =Capacitor; Purple/Wht = ( i'm guessing Agitate or Spin)?? I would like to ask What is Black? Was Black powered through Timer originally?? Pending Direction I imagine; Black,Red,White,and LIVE wire.(Blue added here if you want high speed). Purple and Yellow to Capacitor(I didnt know I could do that), Orange and Neutral wire to thermal switch GE is stingy with the diagrams; Any advice you provide is greatly appreciated. Thanks again