6 ай бұрын
Жыл бұрын
Пікірлер
@thesleevelessfisherman2645 2 күн бұрын
What codes did you have
@vtomic70 Ай бұрын
Helpfull video! But please make sure you drain all the air out of the system before you try to remove the purge valve, otherwise it will shoot the purge valve out straight into your face
@BOBBYB3133 Ай бұрын
does this actuator impact vent changes also or just temperature changes? My airflow is stuck on floor and dash but changing from hot to cold works just fine.
@eugeniujosanu279 Ай бұрын
Just the temp changes
@BOBBYB3133 Ай бұрын
@@eugeniujosanu279 no problem, good video though, however (my a/c-heat issue was the airflow was stuck on dash and floor) after checking to see my actuator was still working like you showed and it seemed to be, i watched the other video you recommended and cut out the panels behind the glove box, and the door was opening and closing properly but still not switching to dash vents. I might recommend to your viewers to do what i should have done first (if they have the same problem i did) which is to check your vacuum lines, particularly the ones by where the battery is. I did find a small vacuum line that had broken off probably due to age and engine heat through the years. I repaired that, taped up the panel i cut out and bam, everything worked.
@osmanromero1169 Ай бұрын
Great job, great video
@fernbarrera598 Ай бұрын
Thank you so much! The instructions that come with the kit aren't very detailed and you did a very good job of showing position and placement of everything. Definitely got me out of a bind.
@alextinpin3577 Ай бұрын
This music should be official music of all American mechanics. 😂😂😂
@eugeniujosanu279 Ай бұрын
Will do .. I'm pretty sure you got special channels for the music
@alextinpin3577 Ай бұрын
@@eugeniujosanu279 Unique
@G0bSt0MpiNgRiddler 2 ай бұрын
Thank you. I’m struggling with putting the snap ring in but your video was a huge help!
@eugeniujosanu279 2 ай бұрын
It got me on the road ..so had to press the snap ring with a flat screw driver ..little bit of struggle
@butlerfamily6870 2 ай бұрын
Thank you
@ahmedalrahal1032 2 ай бұрын
Thank you so much. Very helpful video. Where did you buy the kit from?
@eugeniujosanu279 2 ай бұрын
Volvo dealer ..I wouldn't trust aftermarket
@ahmedalrahal1032 2 ай бұрын
@@eugeniujosanu279 you're right.. thanks
@deanwilcox1698 2 ай бұрын
Thanks for the info. I was happy that my phone has a volume control so I didn't have to listen to the music. Hahaha
@eugeniujosanu279 2 ай бұрын
Talk to youtube about it asap
@ademadem99 2 ай бұрын
Does ecm needs to be recalibrated after installing new 7th injector or is it just plug it and drive
@eugeniujosanu279 2 ай бұрын
No ..this is a mechanical injector (no electrical wiresconnected to it), even replacing the AHI module , no need for calibration
@majaviseibiunouva 3 ай бұрын
Very impressive video 🎉🎉🎉🎉
@JoseLuna-gs6bu 3 ай бұрын
The problem is put back all small pieces on this puzzle
@user-ei4bn4nf2x 3 ай бұрын
Hi bro Can you tell me about size or part number this gaskets Thanks.
@truckertonio9371 3 ай бұрын
Great video much needed and much love
@truckertonio9371 3 ай бұрын
Great video much needed and much love
@flowersfam3462 3 ай бұрын
Which is Solenoid B since there is a code P0755 saying Shift Solenoid B?
@Awake.AwareKFH 3 ай бұрын
What is that sliver box that was attached with the green screws that you removed first?
@justinsmith6860 4 ай бұрын
Copy
@justinsmith6860 4 ай бұрын
All due respect, this video is absolutely pointless, we need the noise on video for comparison in order for it to do any good.
@eugeniujosanu279 4 ай бұрын
That is to show whoever got this problem to check the axle before removing the transmission
@bankergeorge 4 ай бұрын
Poor video quality
@eugeniujosanu279 4 ай бұрын
Kinda hard to do it at 1 am at night with the phone .. sorry you can t catch up
@bankergeorge 4 ай бұрын
@@eugeniujosanu279 I still watch the entire video
@sethmyers8491 4 ай бұрын
Great video thanks!
@ae1731 4 ай бұрын
Great vid
@yuseff_bobr 4 ай бұрын
What a nasty music 🤮
@eugeniujosanu279 4 ай бұрын
...talk to youtube about it. Not gonna pay 30 $ month for your ears. Try to mute the video or mute yourself.
@Louie_831 5 ай бұрын
The cable that was loose mine is hard to move how would i replace them? Mine is the the opposite switch but it gets stuck an don’t go all the way to the opposite side. I thought it was the control but its the wire that gets stuck
@octavioalvarez8934 5 ай бұрын
Still leaking :(
@eugeniujosanu279 5 ай бұрын
Replace the all asambly (may have inner crack) or you installed it wrong .
@octavioalvarez8934 5 ай бұрын
@eugeniujosanu279 I did it 3 times same result
@Mr.Westery 5 ай бұрын
A calm and captivating crime story awaits you. Join in!
@kevinpenner7125 5 ай бұрын
Yup, thanks, genius video, no B.S. just showing how its done. Thanks a bunch. Saved me a bit of a headache knowing that frame came out first. Incidentally the plastic heat duct screws, i believe are 5/16". There hard to see.
@user-rk3tx5zw2q 5 ай бұрын
Thank you bro!
@blake1722 5 ай бұрын
This was sick!!!!
@vasilhristov4228 6 ай бұрын
Do you have part number for O ring ??
@eugeniujosanu279 5 ай бұрын
Sorry , i don t remember the part nr. Just stop at any dealer , they not expensive.. may want to make sure that you can remove it . On the other side I had to buy the all knob since I had to cut it .
@Victor-ue1kw 6 ай бұрын
Can you please link the video for the door you are referring to in the description
@eugeniujosanu279 6 ай бұрын
kzfaq.info/get/bejne/sNN_n6eCtr7Qm6s.htmlsi=UdzPZSCi_mgYNtVP Check this video . You ll get the idea .
@Victor-ue1kw 6 ай бұрын
@@eugeniujosanu279 Grazie mille
@johngibby2026 5 ай бұрын
My AC works fine, heater quit working. Heater core checks out, new thermostat. Could this be my problem?
@FADISALAHAT 6 ай бұрын
The yellow line below the green line is vent or what can you tell me I see mine not connected to any just piece of yellow
@corey9228 6 ай бұрын
Could i manually turn the door until my actuator come in?
@eugeniujosanu279 6 ай бұрын
You should .. still have to take the old actuator out
@salimshamlan3347 6 ай бұрын
kzfaq.info/get/bejne/r7qeiNKbxrKbo2Q.htmlsi=B-p_ZGeVi2cYc5sU
@adriannahunter1986 6 ай бұрын
😁 'Promosm'
@julz7450 6 ай бұрын
This is the best video... Wow thank you so much
@lowgrs1 6 ай бұрын
My father and I thank you with all of our heart. Middle of below freezing weather My dad's driving his truck with no heater. We followed your instructions and he is back to being comfortable thank you thank you thank you
@chrissanders2654 6 ай бұрын
I can't help but notice the Bob barker jail shoes
@daveshostack4950 6 ай бұрын
I had a 340 code and replaced the ignition control module with a gm part and temporarily the code went away. However eventually the timing chain went as per a mechanic. Any person having a 340 code should also check compression. If compression is bad might be your timing chain
@Moonless6491 7 ай бұрын
Thank you. Every other video was showing people hacking the ducts to pieces.
@nathanrodarte4377 7 ай бұрын
Which is solenoid A
@eugeniujosanu279 7 ай бұрын
They should have a nr /letter on them ... check it before replacement, the connector itself is known to have issue
@flowersfam3462 8 ай бұрын
What kind of code reader did you use?
@eugeniujosanu279 8 ай бұрын
Any will work
@shandrew6151 8 ай бұрын
Now that how u make a dam video everything from start to finish fucking awesome bro !!
@davidlucas7208 8 ай бұрын
This video is one of the best examples of how to do a how-to video for automotive. Thanks
@rodneysmith7272 9 ай бұрын
I have every thing out but that second screw on the black piece. How in the heck did you get to it?
@eugeniujosanu279 9 ай бұрын
With a small extension..
@rajunagar3147 9 ай бұрын
Kit number kya h Ji
@eugeniujosanu279 9 ай бұрын
I post it on the video .. specialy for the number .look it up , pause it and write it down
@danieloliver254 9 ай бұрын
man i appreciate this!!
@rajunagar3147 9 ай бұрын
Kit number
@eugeniujosanu279 9 ай бұрын
Watch the video again . You ll see the part nr you need
@luisfmartinez7755 9 ай бұрын
Gracias me sirvio de mucha alludo tu video pude encontrar el problema q tenia. Fue lo mismo. No abria y serraba para ambos lados solo se avia quedado abierto en el aire frio