2 ай бұрын
3 ай бұрын
Пікірлер
@rolandohernandez3273 9 сағат бұрын
You are the mechanic I need from my bike perfect mechanic you are
@salj8610 Күн бұрын
The weight makes it pointless surely?
@kareemalmond Күн бұрын
it’s a proof of concept, why is everyone so pressed
@Apollo1428 Күн бұрын
the design is very human
@charleee666 Күн бұрын
literally rubs the skin of the calf what is this garbage
@HellLetLooseClips420 Күн бұрын
Cool
@AKAKILLINGKING 2 күн бұрын
So was this 48v battery? Low amps what are you powering? Small motor?
@Mobilant_US 2 күн бұрын
This was built for the purpose of building a dual drive 2000 watt sample E-BIKE. A was built with some margin. This is because the front fork dropouts are more likely to break.
@Bigeddie82 2 күн бұрын
Use a toaster oven
@danielsatko- 2 күн бұрын
its absolute crap design
@HuyHoàng-l1i 2 күн бұрын
How about bafang motor? Pls rep me !
@Mobilant_US 2 күн бұрын
To be honest, I like to ride comfortably without pedaling load, so I like the Bafang motor better. Unfortunately, this motor was given to a friend as a gift, and when I put a lot of load on it in the mountains, it started making a bad noise. The motor in the video is a good motor if you ride less than 35 km/h with pedaling as the main focus.
@kayson971 2 күн бұрын
The idea sounds amazing, but the video needs to show more of that bike actually working
@jonslg240 Күн бұрын
Yep.. and also some grease because that's got lots of friction losses lol But if such a system actually gave you more power they'd be using it Clips (clip less clips nowadays) also let you pull with your legs, too, not just push.. letting you use muscles you don't normally use when riding without them, which spreads out the burden across more muscles
@myballshurt435 2 күн бұрын
aint buying it.
@azbgames6827 2 күн бұрын
on my e bike the hall sensor connector is the one with six pins side by side while the controller is like the one in the video. Is there an adaptor for this or do i have to solder? The bike works without the hall sensor plugged in but the speedometer doesn't work
@Mobilant_US 2 күн бұрын
The speed display will not work unless the hall sensor connector is connected. The rpm is measured as the hall sensor turns on and off.
@azbgames6827 2 күн бұрын
@@Mobilant_US nevermind i use jumper wires to connect
@alexiguban3583 3 күн бұрын
What!!! That's 120k pesos in Philippines bimotal motor
@janrhebergen5783 3 күн бұрын
Great animation 😊
@janrhebergen5783 3 күн бұрын
very well done ❤ love your work 🎉
@Mobilant_US 2 күн бұрын
Thank you. 😋😋😋
@chrislamb1224 3 күн бұрын
You need to learn how to bunny hop😅
@theylied1776 3 күн бұрын
This video is fake as Hell! Unless you have a 30.06, that Grizzly is going to a attack you.
@thebossetrino9352 3 күн бұрын
The CGI is so bad😭
@hagakuru 4 күн бұрын
King of EPO
@cybercat8819 5 күн бұрын
Haha this proves joe biden isnt a robot
@user-im8yv6ne4f 6 күн бұрын
hi...want a raise???..make one of those bigger to fit inside a car wheel...connect it to the back plate of the brake mount with a bracket ....attach it to the elaectro magnet case... use multi car batteries....wire it up..don t forget the re charging switch and reverse... congratulations you are on your way to being gas free... god blessed you...
@paulrockwell2644 6 күн бұрын
This guy dork shut up dork
@predator4341 6 күн бұрын
Hi, my name is Sam. I recently purchased electric bicycle 60 volt 1500 watt motor, 26 inch fat tire. My first right didn't go so well after riding for 5 miles when I stopt the bicycle starts moving on its own Without me touching throttle. I was losing also pedal assistant when I was driving. There is no sensors for Pedal assistant it works different way. The bicycle was also increasing speed without me controlling speed I didn't touch the throttle and I wasn't pedaling. Since the owners of the company are located in Chicago, they picked the bicycle after I report the problem. But they are telling me that they cannot find any issue with the bicycle. I present them three different videos with the problem. After I did my research including watching your video I realize that controller is responsible for all the problems that I was having with the bicycle riding for the first time. Any tots, what could possibly happen or what is happening? Thank you. Sam
@Mobilant_US 6 күн бұрын
The structure of an electric bicycle is simple, and cases of it moving on its own have not been reported. The speed is controlled by a variable voltage of 0~5V. If the bike is moving on its own, it is likely due to a short circuit somewhere. I suspect there might be damage to the throttle wires. Since you have submitted video evidence, it would be best to request a replacement for the controller, throttle, or throttle wiring. Best regards, Dr. Road
@predator4341 6 күн бұрын
@@Mobilant_US Thank you
@predator4341 3 күн бұрын
We found the problem after changing controller and the throttle driving for a while. The problem did come back after that. We changed the harness. It was shortage in the wires that connects everything. The bicycle is fine. Thank you so much.
@airforce2195 7 күн бұрын
Ok so we have magic now like wtf
@Mobilant_US 6 күн бұрын
This is actually a video made by Google for April Fool's Day.
@humboldtdoomer866 7 күн бұрын
How does it deter black people from stealing it?
@Mobilant_US 6 күн бұрын
Unfortunately, ebikes these days have location tracking features.
@k1ng5urfer 7 күн бұрын
Very cool build
@malingehring165 7 күн бұрын
This is a great instructional video to show the complexity of the motor. Definitively not a project for a regular owner.
@Mobilant_US 6 күн бұрын
The first time is hard. The second time is too easy.
@operatorpsiochy592 7 күн бұрын
When you change the hall sensors it's also good time to change the bearing. Next time use puller. Save your finger you are lucky the magnet didn't cut you fingers or at least break it. After you disconnect the old hall you should check the old cable it is working properly. That whats you douing hire it DANGER Also you should resoldering the new hall cable. before you close the last cover to close the engine add silicone to get waterproof.
@Supersky_ 8 күн бұрын
That was way too cool for cycling 😂
@FariishAlfiq 8 күн бұрын
whats the girl name
@Mobilant_US 8 күн бұрын
@Violalovescycling kzfaq.info/get/bejne/maxdjcp5ytmlk4k.htmlsi=QymjiAWJuI8Ee_x-
@MaNNeRz91 9 күн бұрын
No solder 😂
@tjapkuh 10 күн бұрын
Traction is all
@yermuther 10 күн бұрын
😂😂😂
@smokefentanyl 10 күн бұрын
I would have used smaller heat shrink instead of electrical tape, especially on a nice build like this and on such critical components. That is bound to fail down the road and result in a never ending pain in the ass chasing down the fault.
@Voltermort 10 күн бұрын
another great one !
@Nutzac 11 күн бұрын
I still want the electric scooter 😂😂😂😂😂😂😂
@cranium420 12 күн бұрын
AND HIS NAME IS JOHN CENA!!
@shanks7929 13 күн бұрын
That's the most ugly bike I've ever seen
@kelsoshuffler4967 10 күн бұрын
AY
@kelsoshuffler4967 10 күн бұрын
ITS A BEAUTIFUL GAMING BIKE
@heraklit8.170 13 күн бұрын
$25,000 seriously?
@MS-un9zq 13 күн бұрын
LEMOND... NOT LEMON
@afolabijamiu9453 14 күн бұрын
I want to repair my motor how can I contact you I am in Lithuania
@Mobilant_US 13 күн бұрын
Unfortunately, I do not do repairs. If you tell me the symptoms of the problem, I can give you advice.
@afolabijamiu9453 13 күн бұрын
at first the motor was very stiff on pedal assist and stop frequently so i decided to clean and grease it but no effect. also, when i thottle and release it the speed continue until i press break and currently it's showing error 30.
@Mobilant_US 13 күн бұрын
Error code 30 indicates a damaged controller if the connector is not connected properly. If there is no physical noise, it is recommended to detach and replace the controller.
@Mobilant_US 13 күн бұрын
If you smell something burning when you open the controller cover, it is very likely that the motor coils have turned black due to water or overload. Parts can be easily purchased from AliExpress.
@hasanalan8049 14 күн бұрын
good job
@Mobilant_US 13 күн бұрын
Thank you~
@zore9297 16 күн бұрын
😢im not rich new one cost me RM3000
@ZemuyBerhane 16 күн бұрын
This is the best so far i ever seen about electric bike
@ZemuyBerhane 16 күн бұрын
Love 💖 it i subscribed
@Mobilant_US 16 күн бұрын
In my personal opinion, the reason this bike didn't reach 400 is because the battery didn't have enough Ah.
@TK-OK 16 күн бұрын
What does the chain do @ 1:41 Regen and propulsion should be taken care of via the hub motors
@bsvride6103 16 күн бұрын
What the hell is bro yapping about
@floris2872 17 күн бұрын
His face 😂
@CanonFirefly 17 күн бұрын
I have a similar vacuum. Just replaced the cells in mine. I used Sony VTC5a cells. Higher capacity and discharge current to the original LGDAHB3 cells. I soldered the wires to nickel strips first and then spot welded to the cells. Prevents heat from soldering potentially damaging the cells.
@Mobilant_US 17 күн бұрын
Yes, that is a better method. The method I used is also good because the heat conduction rate is not fast. It is the method I used when building several electric bikes. No damaged cells were found.