follow the instructions in the elbow package ...can't go wrong ...

Great video but I’m pretty sure you have to measure your 6 7/8 after you have already pressed your copper top.

He is not using an electrician's back reading folding rule? Okay. I used to let those banana peelers and spiral cutters fall on the ground and just score it with a prep knife. After the 500th termination you have it dialed in pretty well. Heating that mess up with the weed burner make it lots easier to work with too. Aluminum oxidizes immediately when it contacts air. If you score into the insulation you can sand or file the scored part back smooth. My oldest stress cone tools are made like Vise Grips with a pull handle on one jaw and blades that cut a square cut and drag a parallel cut like the banana peelers. Those are some really OLD tools. They served me very well, if I bothered to use them.

You should press the lug on before you make the 6 7/8” measurement. That also is the only measurement that has to be precise. After you should use SAP tape from the jacket to the elbow before you connect the bleeder wire to eliminate the possibility of water getting into the elbow.

comme chez nous en france

The first thing he needs to do is take those thick ass gloves off so he can work. What a pussy

Hello, what chamfering tool is that? the one that is made for that cable alone?

You installed your silicone grease from your semi-con over the exposed insulation, if you were working for me, you would be cleaning that again and doing it over. Also, with a little a practice, and experience you can make all your scores and cuts with a sharp knife with more accuracy. When you ring cut the cable jacket, "break" the score with 2 hands and remove the jacket toward your butt cut and there is no need to worry about bird caging the concentric.

you work at abb?

Thank you for posting this.

Checks out

How do you make a solid ring cut in with the bananna peeler

No robo presses? Wow. Do you use ratchet cutters still? And that’s xlp cable. That isn’t used anymore where I work.

Whenever you start doing nonessential tasks for the sole purpose of aesthetics then you have strayed from the path of a competent installer. "Gee Bob, look how much time Mr. Smith wasted making this elbow look a certain way even though it made no difference in performance or safety." Good thing most linemen work for the public where they are not held accountable for their productivity.

Great video!! They are called Linesman pliers not Kleins. Klein makes them. Just busting balls.

where are your PPE steel toe boots ?

Work that looks good works good

Why wipe off the inhibitor? It's there for a reason.....

Just started off as a UG apprentice very informative video. Thank you sir.

5:12 Don’t take off your PPE 😂

Just a little hard to watch.

Where did you get the chamfering tool at?

The V part of that probe tool is used so the wire sets it’s self along the wire and you can use a ratchet motion to strip back that jacketed neutral!!

Always nice to see how other places to it. We do ours a little different. We strip the outer jacket until a few inches above the conduit. But a water seal around it and that cable is so much more flexible. Also we twist the bleeder wire on to the concentric and wrap it going up the elbow before landing it. Solid video. Always wondered how these elbows differ from other styles.

Well done, 2 things that got in my mind during the video. First, the press fittings that I know had to be started all the way back and than the second, third, fourth towards the lug. In that way you'll force the conductor into the press fitting and create additional contact area at the conductor face. It might not be important on small connectors like this, but definitely on 1000+ amps. Second thing the grease/clay inhibitor, you want to have the full amount of it inside the press fitting to guide heat out of the core and transfer it into the lug. Beside the temperature thing you also make sure that humidity has no chance to enter even if the outer isolation fails over the years.

Hold. The. Phone. HORIZONTALLY. For the love of god.

Why not use a regular splicing knife, you don’t need all those fancy stripping tools.

People like you really make KZfaq a valuable tool. Thanks for taking the time so share your knowledge.

Excelencia y más

All good but one tip for those working in a hot tx. Make sure to keep those concentric away from anything that ain't equipotential to ground.

Don't piss this guy off he'll give you pushups like there's no tomorrow

Solid videos dude. A lot of good pointers 👍🏻

This man gives out push ups like Santa gives out presents!

Horrible

This was very informative. Loved it

What is the brand and part number for the pre-determined chamfer tool ?

AWESOME helpful video!

Great work!