Actually really helpful! Got a 95 600 katana I'm doing for my gf.... Bikes been sitting for years but it starts an runs. Pulled the carbs cleaned them an got an improvement out of it. Just got my sync tool in an I think I'm gonna sync the carbs some time this weekend to just get it dialed completely. So far your the only person that went a little more in depth on sync screw locations. So thanks
@motorman97 күн бұрын
@@moglie431 Glad to help! That's the goal. Not that I accomplished a good tune on mine 😂
@guillermohuato57878 күн бұрын
You need to replace the turbo lines and intercooler or they will keep blowing
@motorman98 күн бұрын
@@guillermohuato5787 why?
@guillermohuato57878 күн бұрын
@@motorman9 The lines feed the oil to them and let the oil flow out of the turbos if the lines are bent on the way out or on the way in it will keep blowing the turbos do to not enough oil getting to them or hot oil not draining properly will cause them to slip the turbine shaft instantly
@guillermohuato57878 күн бұрын
An your intercooler is clog up with oil if you haven’t replaced it
@motorman98 күн бұрын
@@guillermohuato5787 the oil lines are fine, & I have an Intercooler drain
@motorman98 күн бұрын
@@guillermohuato5787 never heard of anyone replacing an Intercooler with a turbo. Clean it, if anything
@lane968521 күн бұрын
Dude mine gets up to 85 mph takes a minute but she gets there 😂
@herbindavidovalle346725 күн бұрын
Is this stock?
@motorman925 күн бұрын
@@herbindavidovalle3467 Believe so, but it may be tuned
@herbindavidovalle346722 күн бұрын
@@motorman9yeah pretty sure it has been remapped cause of the way it launches at 2,500 rpm. In stock ecu map it doesn’t build any boost to make a kind of agressive launch
@motorman922 күн бұрын
@@herbindavidovalle3467 That's interesting. Seemed a bit quicker than stock...
@mema2376Ай бұрын
Dude made an hour video into a 8 minutes video. Kudos
@TonightsMainEventАй бұрын
My 82 xs 400 runs and idles fine up to 3/4 thorottle and then bogs out do you know what this issue would be?
@TonightsMainEventАй бұрын
Also, sometimes I can get to full throttle easying on it
@motorman9Ай бұрын
@@TonightsMainEvent brother, i can't even figure mine out, but sounds to me like your main jet/s is/are plugged. Runs better on choke? If so, needs more fuel. Maybe plugged, may be fuel screw
@TonightsMainEvent29 күн бұрын
@motorman9 I think I figured out my issue(s) I had a slight vacuum leak on the vacuum line on the petcock and the problem still occured. I ran it with out the pod filters and bam. With out the pod air filters and I can bang through all gears, problem is I don't have an air filter now lol
@motorman929 күн бұрын
@@TonightsMainEvent hmmm... interesting. I may have to diagnose my hard cold start more...
@TonightsMainEvent28 күн бұрын
@motorman9 apparently these old yamaha/suzuki bikes carbs can be pretty temperamental from what I hear, and people needed to rejet with smaller jets if using pod style air filters, allegedly if that helps at all
@barbaraarsenault1192Ай бұрын
Holding over? What does that mean? I have the same problem.
@motorman9Ай бұрын
@@barbaraarsenault1192 Holding the key over while someone connects the cable
@larryballard9412Ай бұрын
never use a torque wrench to break loose anything please
@motorman9Ай бұрын
@@larryballard9412 Why?
@johndow-g5iАй бұрын
thank you, having the same problem
@stephaniefrey16282 ай бұрын
You literally didn’t even show how to take a window out
@motorman92 ай бұрын
Could've probably been worse for one of my first ever videos 😁
@kelvenguard2 ай бұрын
My Dad (83) just came home from Auction with the same used machine... NO Idea how to use it...
@motorman92 ай бұрын
Hopefully he got a good deal, & Hopefully this helps
@kelvenguard2 ай бұрын
@@motorman9 it did help... he payed $1000 Canadian... Same Machine NEW is $2495 Canadian... Everything works, it was a Outside Machine so Sun Faded and Arms are raised 4-5 inches thinking to clear wide skid steer tires, I can lower back to Factory easily...
@kelvenguard2 ай бұрын
@@motorman9 The Tire Machines with the Single Arm and No Bead Blaster are $1500.... But the Double Assist Arm and Bead Blaster Tank on the back are $2500... I could be wrong but thats what I'm seeing at Uncle Wieners in Edmonton Alberta :) I've done 100s of tires by hand... Back when I was 13 years old Dad would make me do 10 Split Big Rig Rim's ALL saturday He told me to wrap a chain around the tire and rim incase it BLOW UP !!! I like WHAT these BLOW UP ???
@motorman92 ай бұрын
@@kelvenguard Oh yes, that's right. & I knew that. I just bought mine 😂 Not sure why i got them mixed up. Not bad, then!
@kelvenguard2 ай бұрын
@@motorman9 Lol...............its a Mixed up world so were ALL mixed up....
@digitalbilly2 ай бұрын
Cool video got a parts list of what filters you use?
@motorman92 ай бұрын
Unfortunately not. I don't use that anymore. Centrifuge is really the only practical way if you plan on doing any real amount. Goldenrod 495/496, Goldenrod 80 mesh screen, & whatever filter hosing takes cheapest filters. Google should tell you the rest
@Xxx_Lord_Poop_xxX15 күн бұрын
@@motorman9so what happened that made you switch to a centrifuge?
@composing02 ай бұрын
Hello how are you Do you try using a milk separator instead of this device, it works at high speed What's your opinion?
@motorman92 ай бұрын
Can't say I'm sure what you're talking about
@composing02 ай бұрын
@@motorman9 I haven't tried it. But I think theoretically that the milk separator purifies diesel
@drzevodrzevo2 ай бұрын
Thanks man! We're having same issues. This weekend we're gonna try to fix it! Regards from Poland!
@motorman92 ай бұрын
I'm lazy & hesitant to try anything, & this was easy! Should've done it LONG ago. Lost almost 2 years
@drzevodrzevo18 күн бұрын
@@motorman9 Hey! Just wanted to say we've fixed our Sea Doo 3D Thanks to your advise. It runs like hell !!! Cheers !!!
@motorman918 күн бұрын
@@drzevodrzevo Hell good or bad? 😂
@nextdevelopments88333 ай бұрын
Nice simple set up... thanks for sharing. I'm looking at doing a smaller scale version in my bus so we can run wvo as we travel... the intersting thing will be setting it up to be able to run this AND pump diesel interchangable.
@motorman93 ай бұрын
I've been considering just a mobile centrifuge setup. Shouldn't be hard to make. I'm always single stock tank
@user-cr2xc9fo5q3 ай бұрын
the helmet lock on the right side below the seat is also a seat release. insert the ignition key and turn clockwise. this will release the seat latch.
@Dontbeafraid23 ай бұрын
Put your seatbelt on!!
@Dontbeafraid23 ай бұрын
You should do this again but in "s" mode
@user-gk5je9wu4u14 күн бұрын
yea fr the manual mode makes a fuck ton of difference 😭 least in my 2013 one shit goes from js pushin u back a lil to fully throwin u a good bit
@Dontbeafraid214 күн бұрын
@@user-gk5je9wu4u would you recommend it as a first car?
@charmont9443 ай бұрын
About 3 seconds
@kenipanaque87053 ай бұрын
What
@coastalrob9836Ай бұрын
a little over 9 secs. Speedometer is in Km/h not mph.
@XsaviXander4 ай бұрын
My ATS and CTS is faster.
@motorman94 ай бұрын
WOW! Your cars that weight less than half what this truck does with at least 70% of the HP are faster than my big, basically stock 9k lb 4x4 crew cab Z71 truck? That's insane! I mean, who could've guessed that?? 🤔🤷♂️
@XsaviXander4 ай бұрын
@@motorman9 I know, right?
@runs02904 ай бұрын
No comments but I’m here to say I love u
@veebes63674 ай бұрын
Top speed?
@motorman94 ай бұрын
Not even a question I care to find the answer to 😂
@veebes63674 ай бұрын
@@motorman9 aa man, maybe you can try it😮😁
@motorman94 ай бұрын
@@veebes6367 That thing is LONG gone. They come & go all the time, so I take lots of videos 😁
@thecannyflyfisherman88154 ай бұрын
Dude you’re awesome I’ve had almost every issue you said with mine and I wish I saw this video years ago but now it’s the motor mount
@pFUSIONq4 ай бұрын
Whats the gauge on the left that maxes at 760 i have 1998.5 24v mine dont have that
@motorman94 ай бұрын
Sure it does. Just different units of oil pressure from Canadian trucks. VP44s have different gauges, anyway.
@daneitor974 ай бұрын
Where you got the centrifuge?
@motorman94 ай бұрын
WVO Designs through Chris Heil on NotSoGrand Garage on KZfaq
@patrickdeloy69394 ай бұрын
Awesome video...quick and dirty...perfect. I have that exact model and color. Please continue exploring as it makes my discoveries less dramatic...more cost effective too😊
@motorman94 ай бұрын
That bike is long gone, but I work on all sorts of things, as they come & go :) Might do another video dump in a bit, as I need the space
@scotttrafford26174 ай бұрын
Is this the Twin turbo Flex? I have one, and I can't believe how quick she is.
@motorman94 ай бұрын
That is the one, yes. EcoBoost. Same engine as the SHO. You can see they're actually pretty close, though obviously the SHO is 400lbs lighter & faster
@tonydiesel34444 ай бұрын
3 gal max per hr
@motorman94 ай бұрын
You can run whatever flow you want. Slower is cleaner
@tonydiesel34444 ай бұрын
Anyone need a centrifuge I sell new big AC power direct drive units with clear lid shipped for a thousand bucks
@marcobiagioni4 ай бұрын
❤❤❤
@abramheide73274 ай бұрын
Thank you very much for the video that was very helpful
@RedFernPropertyMaintenance4 ай бұрын
that's awesome bud! thanks for sharing
@ExpediteTravels4 ай бұрын
Are you from Canada or the USA ? Also where do you get your oil from
@motorman94 ай бұрын
Canada. Any restaurant that wants to give it up. Thought I mentioned that. I just call around
@ExpediteTravels4 ай бұрын
@motorman9 ah you're a fellow Canuck I'm from the Windsor Ontario area Thanks for getting back.
@motorman94 ай бұрын
@@ExpediteTravels, & yet 2,500km or so away in SK 😁 My pleasure. What are you running it in?
@rmhittle5 ай бұрын
i like the shotgun blast of information. I came here not knowing any of this and now i feel like i know at least a little bit about a lot different stuff. good starting off point for me.
@motorman95 ай бұрын
😂 Glad to help! Sometimes I talk too much
@JessicaJohnson-mv7lb5 ай бұрын
That was bout 60😂
@motorman95 ай бұрын
Yeah, triangulated GPSs lie all the time, 4 runs back to back. It's amazing & ridiculous that people even still use them 🤷♂️
@high-octane-stunts865 ай бұрын
A stock new truck would gap that still 💀
@motorman95 ай бұрын
Congratulations! Also, why did you die?
@MrDave5905 ай бұрын
Wow My company van moves faster than this and the Type s with full equipment and tools added that. Still a cool little car though.
@motorman95 ай бұрын
They are SLOW! Would be cool to see what theyd do with some boost, though. May be better for boost than the Type S motor with likely lower compression(like LQ4 vs LQ9). Wonder what they auto transmission would hold....
@user-wo3vv1qz4k5 ай бұрын
Good bar
@brianw.67186 ай бұрын
I'm really surprised that Wildcat kept up as well as it did. I'm about to get a Wildcat 1000 in the morning and super excited about it.
@motorman96 ай бұрын
These are both slow. That Can Am isn't NEAR as fast as it should be, but one day I'll spend a bit of money for a proper tune. Wildcat 1000 is fun, & likely the best handling SxS I've owned, but plenty problems. Make sure the engine case is reinforced, or the starter/kickback will break it, upgraded or not. Anyone with some aluminum welding abilities should be able to do it. Rear differential/clutch finally went just cruising, & I sold it. If it's a newer Textron unit, thats basically a Yamaha, & likely an excellent unit
@brianw.67186 ай бұрын
@@motorman9 well considering this is going to be my first sxs, what would you recommend? My options are a 2013 Maverick 2 seat, a Commander 1000 (lifted kind of high), the Wildcat, or a 2016 RZR 900xp.
@motorman96 ай бұрын
@@brianw.6718 , honestly, if the value is the same on all, the Wildcat would probably be last. RZR & Commander aren't fast, but the RZR is common. Any of the others should be a good choice. Maverick is probably fastest/sportiest
@tomakafrankconlon32076 ай бұрын
Why is someone that has no idea of how the Madura engine works trying to make an instructional videos?
@motorman96 ай бұрын
Hey, Tom! I appreciate you taking the time for the view & comment! Feel free to do the same with the rest of my content. &, if you're feeling particularly generous, take a break from the condescension & educate me!
@tomakafrankconlon32076 ай бұрын
@an9 More than happy to. You suggest over and over that you dont know "what these are called". Obviously you need KZfaq validation. Broken water pump tensioner has nothing to do with dumping the clutch. That aside your engine would have overheated in less than 10 minutes without a working water pump. . That aside when you say you may keep the fried clutch plates to use later you are really unknowingly suggesting dangerous advice to others.. People watching this might believe you and end up with a motor spinning out and cause an accident. The clutch basket holds the clutch plates. "I was an idiot and blew the clutch on my Madura. So I took this video to hopefully help someone else out if they have concerns(even though I don't know what I'm doing...)." Do you want me to continue?.
@motorman96 ай бұрын
@@tomakafrankconlon3207 😂😂😂 Oh, man.... That was rich. Take care! Don't forget to spend some time on my other videos. You obviously have the time.
@davidworth76216 ай бұрын
Hello Motorman. Stumbled on your video. Thanks for the explanations. I have a Blue Viper wheel balancer. I need some help on 2 issues. Sometimes when I balancer a plain steel wheel I get the OPT on the control panel middle leds. What does that mean? And during my search to find out what OPT meant I came across OPTIMISATION. OPTIMISATION is performed on wheel badly out of balance. What is the procedure and how do I perform OPTIMISATION wheel balance on Blue Viper WB100?
@motorman96 ай бұрын
Hey, David. I would imagine it would be the same as any other wheel. My experience on this or any tire machine so far is less than 10 wheels, so unfortunately my advice is limited. I would message Uncle Weiner's, & I'd bet they could help
@davidworth76216 ай бұрын
@@motorman9 thanks for the reply. funny you should mention that. they couldn't help me.
@motorman96 ай бұрын
@@davidworth7621 , would the manual help you? I may be able to send you that if you give me an email or the like
@davidworth76213 ай бұрын
@@motorman9 thanks I have a manual. I just balance a few wheels a year. Every now and then I get a OPT on the screen and I don't know what to do. Do you think it wants me to optimise the wheel?
@motorman93 ай бұрын
@@davidworth7621, I couldn't tell you. I know very little about them
@MyTimmy756 ай бұрын
Good job Kiddo :)
@MyTimmy756 ай бұрын
And. This is good to know if ever you don't have that threaded clutch spreading tool, Or the hole threads are stripped ;)
@MrDaicon236 ай бұрын
Any idea where i can find the Map sensor for Patriot 2011 2.4L?
@motorman96 ай бұрын
Amazon, Ebay, RockAuto, & plenty others, I'm sure
@KtothG6 ай бұрын
could u do another take with more nauseating camera motion?
@motorman96 ай бұрын
Appreciate the comment, brother! Be sure to visit all my other videos & do the same there. You obviously have nothing better to do with your time 😁
@professionalredneck79206 ай бұрын
Flip your oil cap upside down on your fill point and if it stays put, you dont need to be worried about the blowby. The stalling would probably be either a dirty fuel filter or something like IPR (injection pressure regulator) sticking. If your batteries aren't charging, i would look into alternator or voltage regulator. If youre just talking about why your battery charger is ot working however, that is probably because you want to have your charger hooked up to the Right Side battery, not the left. Edit: The stalling could also be a bad CPS (cam position sensor).