Normalmente para corrigir pé manco cruzado coloca se calço nos pés que é para corrigir, poque so colocou calço no pé de menor correção ?
@paulpaulzadeh61727 ай бұрын
Great video , learn a lot 😊
@user-si9ql8lj2f10 ай бұрын
Super sir
@ronaldomarques8029 Жыл бұрын
Excelente aula top de mais muito bom
@mechanicalkiller1061 Жыл бұрын
Perfect LUAI Rotating Equipments Engineer
@acoemsweden Жыл бұрын
Thanks 😀
@ronaldomarques8029 Жыл бұрын
Eu gostei dessa aula de alinhamento ótima apresentação me manda mais pra mim. desde já agradeço parabéns
@ronaldomarques8029 Жыл бұрын
Excelente aula o alinhamento top 🔝🔝🔝
@storm_bringer2266 Жыл бұрын
is it required to put the laser beam on both black center line of movable and stationary ?.
@DesignBuildandTest Жыл бұрын
I just want to see the mechanism by which a coupling works. Why is this so hard for you ?
@ericbasty22 Жыл бұрын
MIN 2:52 AQUI LO INTERESANTE...
@veerapandi37732 жыл бұрын
Could you pls clear my doubt's? 1#Minimum Fixing distance? 2#Which is we want to set first? H or V 3#Once complete alignment the readings all correct but while checking again that all reading was changed. What is the reason, why and how to correct? 4# Where should Fix the Leaser Fixer (Chain clamp ), Coupling or Shaft 5#How to do Alignment coupled conditions or Decoupled Conditions (What is the reason?) 6#Some time one angle is shown in down side, Is this problem or not problem? How to set both Angle reading in Top side?
@user-fi4zp7gn4p3 жыл бұрын
Датчики. Тем. и хороши , когда. они. максимально. компактные .....много. лишнего. Мусора. на. Дисплее ....Кнопочные. намного. Лучше (стаж. работ 22 года на. лазерах , общий 44 на. томже. предприятии)
@AlphatecEngineering3 жыл бұрын
Great video folks!
@johnhull63633 жыл бұрын
Used one today to align first stage axial compressor (15 tons) to second stage (8 tons) makes it a lot easier on yourself limiting the number of times you have to make shim changes. 2nd to motor Monday after large bore piping installed and no pipe strain affecting the compressors, never align to the piping.... you pipe to the pump!
@AlphatecEngineering3 жыл бұрын
great tool!
@AlphatecEngineering3 жыл бұрын
Great info, thanks for sharing it.
@AlphatecEngineering3 жыл бұрын
Excellent summary! thanks for the video.
@prashantmishra11834 жыл бұрын
Plz upload single plane and two plane blancing
@herbertXX4 жыл бұрын
i love alignment
@user-py1hz9ik2i4 жыл бұрын
why tell that it’s hot in summer and cold in winter ...
@eugeneb36824 жыл бұрын
Thanks Very educational
@user-pn8so4qd9v4 жыл бұрын
Не понял смысла !?
@user-pn8so4qd9v4 жыл бұрын
1,30мин проверен десятилетиями в работе ! ЛАЙК !
@user-pn8so4qd9v4 жыл бұрын
Не понравились зажимы датчиков к стержням стоек , по 2 винта удобней и долговечней ! ( из практики) .
@user-pn8so4qd9v4 жыл бұрын
1,30 мин , фото ,,КЛ,, Работа 1995- -2017 ! Ставлю лайк !
@user-pn8so4qd9v4 жыл бұрын
Не правильно нахлобучил датчики на стойки , что и сказалось на S t позиции ! Не спеца сразу видно по мелочам ! В любой работе голова идет на шаг впереди , чем руки !
@gandhi19604 жыл бұрын
I am interested in knowing how to measure flatness of a rectangular metallic mounting pad (for turbine) LxW (1meter x 0.4 meter) and flatness specified by turbine manufacturer is within 0.030”/ft (2.5 mm /meter) and coplanar to 0.120” (3.0 mm) to the other pads.
@prabhaddlg16405 жыл бұрын
Please send me the laser alignment of documents please because I need to learn more and more
@kr4k3nonb615 жыл бұрын
Vim através do SENAI RS 🔥
@anthonygiordano62656 жыл бұрын
Hello have a question is offset misalignment the same as parallel misalignment?
@umeraftab30726 жыл бұрын
Yes
@llRoBiNzll6 жыл бұрын
Excelente equipo.
@huyhoangbkdn7 жыл бұрын
can you share for me a little Shaft Alignment Concepts document?thanks so much