The_BaderBuilt

Пікірлер

@andrewwilliama9216 14 сағат бұрын

Bolton Mississippi, I have a 1993 Chevrolet W/T C1500 Cheyenne long wheel base.

@noritanicole484 Күн бұрын

Hi master, how about my honda crv 2008 as my fan automatic on once I key in. Do I need to remove the fan power supply as my fan not automatic before i go to next step for 3k rpm ? Thanks master

@the_baderbuilt Күн бұрын

With your fan being electric, keep your AC off and follow the same steps. I would recommend doing it either early morning or late evening so the temperature is cooler. If I have more information I will respond further. Thank you.

@mondizoo559 16 күн бұрын

I lost my shit when you said 5:10 😂

@permanadanwaktu7778 Ай бұрын

I heard sounds like power steering air leaks

@abrahamjoseph6707 Ай бұрын

Any recommandations 2007 accord with 300k miles for better engine performance. Already changed all filters and fluids.

@abrahamjoseph6707 Ай бұрын

Also has an oil consumption issue.

@the_baderbuilt Ай бұрын

Oil consumption issues could either be caused by a worn cylinder or piston rings being gummed up. I would recommend doing a seafoam treatment on the engine and letting it set for a few hours before driving it. Then, a day or two before your oil change I would add 1oz of seafoam per quart if engine oil and drive it. You could also try marvel mystery oil before your oil change. I have had luck with both freeing gummed up piston rings. Considering the high mileage it's more than likely worn parts, but it's worth a try.

@the_baderbuilt Ай бұрын

Check out my other video's titled the 9 dollar cure for a sluggish car and the 15 dollar fix for poor acceleration. I cover seafoam treatment and MAF/Throttle body cleaning in those video's. Both processes will improve performance.

@ImJaidee-ip4et 2 ай бұрын

I learn so much from your videos, thank you!

@ThomasHall-zb7xl 3 ай бұрын

Only use throttle body cleaner on the throttle body. There is a protective film. Never use carburetor cleaner on a throttle body. He had the throttle cleaner

@the_baderbuilt 3 ай бұрын

That is correct. Thank you.

@the_baderbuilt 3 ай бұрын

That is correct. Thank you.

@sabrinakirksey 4 ай бұрын

I love your videos!

@krod2162 4 ай бұрын

I don't think you did the keep it simple process here. A lot of times you can clean the throttle body while it's on the car At least that way , you won't have to mess with that stuck on gasket

@the_baderbuilt 4 ай бұрын

Sure, it can be done in different ways. I didn't want to wash all the carbon and dirt into the plenum. I have done both and I prefer this process.

@friar1968 4 ай бұрын

1993 Chevy Cheyenne… worth the money to restore? Could I email you some pics?

@the_baderbuilt 4 ай бұрын

[email protected]

@BuyExcelTemplates 4 ай бұрын

Thank you for the video!

@zogzog6611 4 ай бұрын

Terrific video! Very methodical, filled with practical tips. I especially appreciate how you didn't skip over the fussy/tricky parts that frustrate us would-be DIYers. Showing them speeded up was a terrific idea. Two questions: (1) If you did touch the throttle blade and open it with your fingers, wouldn't the car's computer automatically adjust it once you restarted the car? Or is there an explicit reprogramming process? (2) How effective would it be just to clean the throttle body without removing it--that is, just clean the outside?

@the_baderbuilt 4 ай бұрын

Thank you for the comment. If I had moved the throttle blade, it would need to be reprogrammed. There are two ways to complete that process. One is to use a scanner with that functionality. The other is a manual process by revving the engine to a certain RPM for a pre-determined amount of time. As for cleaning, you could make a difference by cleaning it on the plenum. It will not be as thorough or as clean. The other reason I removed the throttle body is so I didn't flush the dirt and carbon down into the intake.

@zogzog6611 4 ай бұрын

@@the_baderbuilt Ah, I see. Thank you for explaining both! Although I should have figured out the second one. Plus I got to learn a new word: plenum. Many thanks!

@tlak 4 ай бұрын

Looks like a problem to me. You're only cleaning one cylinder. Maybe as a liquid it falls down into the connecting channel.

@the_baderbuilt 4 ай бұрын

So with that logic does a carburetor only feed one cylinder?

@tlak 4 ай бұрын

@@the_baderbuilt The vacuum hose goes into the front tube and if you were feeding more vapor it would only go into one tube/cylinder. Or did you not see that.

@BenjaminHansen 4 ай бұрын

Regarding your HF snapoff torque wrench, it appeared to be the type that can be calibrated, if you were concerned or questioned its validity.

@the_baderbuilt 4 ай бұрын

I wasn't sure if they could. Thanks for the info.

@BenjaminHansen 4 ай бұрын

@@the_baderbuilt I have yet to do mine (I had it "verified" at my old metrology lab), but it is doable if it has the large nut on the end of the handle.

@joseluisrincon2993 5 ай бұрын

Evening!!! Where is the maf sensor on a 2006 honda accord. Cant see it where it is on this car on the video.

@the_baderbuilt 5 ай бұрын

The maf sensor is the little one I pulled out and cleaned. It's attached to the front of the air box near the intake tube.

@sabrinakirksey 5 ай бұрын

Dude, good video! 😊

@sabrinakirksey 5 ай бұрын

Awesome video!

@armandozara2780 5 ай бұрын

What happen if you didn't take out the plugs of battery the time that you cleaned

@the_baderbuilt 5 ай бұрын

All sensors are electrical. I don't want to risk a short or sending feedback through the circuit. Theoretically, with the key off no power should be supplied, but if nothing else it's good practice.

@fabrivila2774 5 ай бұрын

Thanks for the video. According to everything you did except using a metal brush, better using a toothbrush, it will not damage the throttle body.

@TC-hb2gn 7 ай бұрын

There is an actual Honda specified idle relearn procedure. You can look it up. Airflow parameters are being changed so I beg to differ that it isn’t necessary. It doesn’t take a lot of time. Being thorough will never hurt.

@the_baderbuilt 7 ай бұрын

I actually agree with you. The accord I did this on did not need to have a relearn preformed. It idles smoothly and performs flawlessly afterward. My silverado did need a relearn done because I bumped the throttle blade. I'll address this in the next video. Thanks for the comment.

@OzarksTruckin 7 ай бұрын

Looked to be a very good throttle body cleaning. Liked that info on K&N filters too👍

@the_baderbuilt 7 ай бұрын

Thank you.

@tonymeehan7859 7 ай бұрын

Mothers aluminum polish with a buff wheel works just as well as this without all the extra sanding

@the_baderbuilt 7 ай бұрын

Does it really? I'll give that a shot next time.

@saginaw60 8 ай бұрын

We keep hearing "Phillips" screwdriver. Try "JIS" Japan Industry Standard, made not to cam out, not to strip. Tool stores sell 'em, not hardware stores.

@the_baderbuilt 8 ай бұрын

I've been hearing JIS lately. I'll check out a set. Thanks for the comment.

@metzmatu8409 8 ай бұрын

Yes, I use the JIS type screw driver and work fine for that throttle body & MAF screws.

@shane6284 8 ай бұрын

I don’t think you used enough of that cleaner.. Maybe another can would have helped?

@the_baderbuilt 8 ай бұрын

Picked up a case just for your viewing pleasure.

@shane6284 8 ай бұрын

Oh good! That should last you a couple days..

@TheMauser98a 8 ай бұрын

Drives as fas as my truck. I will eventually get to 60mph hahaha

@the_baderbuilt 8 ай бұрын

Haha it's a slow ride for sure

@TheMauser98a 8 ай бұрын

Enjoyed the video great sense of humor, keep up the great 👍 work. I have 2 trucks a 1987 chevy stepside and a 1994 gmc stepside.

@the_baderbuilt 8 ай бұрын

I'm jealous, I need another. I appreciate the comment. Thanks buddy

@jeffwest5551 8 ай бұрын

Brutal. Not supposed to use carb cleaner on throttle body. It's why they make throttle body cleaner. Nor would I ever use a wire brush. Use a shop rag.

@the_baderbuilt 8 ай бұрын

It's throttle body cleaner.......... also the wire brush is brass and plastic. Softer material than the aluminum. Brutal comment

@jasonsharpbucks 7 ай бұрын

@@the_baderbuiltaluminum is softer than brass

@jonathanmata565 8 ай бұрын

Dealer charges $ 350 and I did it myself 😆 🤣 😂 😊

@user-kj6cw1wl7u 9 ай бұрын

What part are you cleaning?

@the_baderbuilt 9 ай бұрын

Doing this will clean the intake runners, valves, and the tops of the pistons.

@jasond4752 9 ай бұрын

I'm just amazed at how clean that bay is and that there's not a speck of rust on anything.

@the_baderbuilt 9 ай бұрын

I try to keep my engines clean. As for the rust I live in AZ so we don't have crazy winters or salt to deal with. I make a habit of cleaning mud off my cars immediately. I appreciate the comment.

@jasond4752 9 ай бұрын

@@the_baderbuilt I'm from AZ but now live in PA. I had no idea cars rusted like they do until I moved here. Now when I see a car from the west I'm amazed, lol.

@erniediaz2433 9 ай бұрын

Great job love what you do

@the_baderbuilt 9 ай бұрын

Awesome to hear! THANK YOU

@theroyalcrownedtiger2946 9 ай бұрын

Looks like 2006 Accord engine bay, with the 2.4L motor.

@the_baderbuilt 9 ай бұрын

That's exactly what it is.

@MrMarcel114 9 ай бұрын

After a. Throttle body cleaner all Honda Vehicle Needs relearn , no matter what you do if you move or touch with a finger you going to a relearn.

@the_baderbuilt 9 ай бұрын

If you manually open the throttle blade then yes. I had my fiance floor the car to open the blade. The car runs smoother than it has since owning it.

@zepp3lin 9 ай бұрын

Just drive normally, and the ECU will learn by itself.

@metzmatu8409 8 ай бұрын

I clean the butterfly valve at every 30k miles, with minimal gunk, no issue with idling speed.

@muhammadchiroma9675 4 ай бұрын

@@the_baderbuiltMy throttle was manually opened by an inexperienced mechanic and since then the idle have been very rough. How do I resettle it? Honda Accord 2007 model

@didurightaguilar5974 Ай бұрын

So if you manually push the throttle blades u have to relearn ? If u did it a safer way being having a friend push gas pedal then you shouldn’t need to re learn ?

@maolo76 9 ай бұрын

great video. you didn't clean the iac valve. i didn't see you burp the coolant since you open up the coolant line. i saw another video he fill any coolant loss and then burp the coolant system of air after removing the throttle body.

@metzmatu8409 8 ай бұрын

This type of throttle body doesn't have IACV. At 21:39 he mention the butterfly opening at idle, see through at slight opening of the butterfly valve. That why self relearn of the throttle valve and make adjustment for correct idling speed due to gunk/dirt, no IACV required. To keep the butterfly valve openning as per factory setting, I clean the butterfly valve & internal throttle body every 30k miles on my Honda.

@tomkoolman 9 ай бұрын

For this Honda engine, I would put the key at ON and put a brick on the gas padel, the throttle body should opened up. Then I soaked microfiber cloth and carefully wipe off the carbon on both flap and tunnel.

@the_baderbuilt 9 ай бұрын

Good tip. I had a my fiance push it the pedal down for me. But working solo like I usually do that would work well. Thanks for the comment.

@kayjay4060 3 ай бұрын

This is exactly how you should do it. Careful that whatever you use to open the throttle body butterfly valve doesn't allow it to snap shut. That could be a very bad day if you have your finger in there. That motor will try to close it with whatever power that motor has. Do not spray the cleaner on these motor drive throttle bodies. The cleaner can get into the openings at the valve, and cause electronics to fail. Just need to clean where the butterfly valve meets. The valve is nearly closed during idle, and that is when it matters. That carbon blocks the air flow. Once you push on the accelerator pedal the valve opens and it doesn't matter one bit. Only during idle is this an issue. So the only part that needs to be cleaned is that little gap when the valve is shut.

@HVAC69 10 ай бұрын

Great video thanks a lot for sharing your great working knowledge ...

@the_baderbuilt 10 ай бұрын

Thank you

@KP-16v 10 ай бұрын

Great video, maybe avoid the wire brush on the throttle plate to avoid removing the factory coating.

@the_baderbuilt 10 ай бұрын

I used a brass and plastic bristle brush. It should be fine. It's only air that flows through the throttle body, I have had ported ones in the past with no issue. Thank you for the comment.

@loafwicks2ks_478 10 ай бұрын

Hotter than a stolen hellcat 😂😂

@hmroa3056 10 ай бұрын

I appreciate the tip about (1) not manually opening the throttle body blade, and (2) about expecting coolant from the hoses connected to the throttle body. Thank you.

@the_baderbuilt 10 ай бұрын

I've learned the hard way in the past. Glad it helped.

@jimcollins9999 3 ай бұрын

@@the_baderbuilt... what if you did touch the blade & opened it while cleaning the throttle body as I did, what has to be done afterward to correct that mistake?

@motorwolfe 2 ай бұрын

@@jimcollins9999 you will need to hook up an OBD diagnostic tool and perform a throttle body relearn procedure. I cleaned the throttle body on the exact same Honda K24Z2 engine featured in this video, 2010 Accord. the idle would hang momentarily when letting off the gas - doing the relearn cured that.

@robertclarkguitar 10 ай бұрын

I have a 92. Ex cab 8 ft bed .the interior is over. Done. Hahah but it works and runs no smoke...paid 1800 in 2012. Put 5k if that on it as i lived a mile from work and only went to work. Its sat now since 2019. I bought new battery and drive it over to where i live now at my daughters as i watch my granbaby for her. Its bit ugly but the 350 tbi fires up and trans im not sure i guess its the same as all tbe 350 tbi tow package long bed ex cab c1500s. Lol. The guy i bought it from said it was rebuilt at 30k miles ago in 2012 it was 196k. No smoke ...ran him 60 miles back home and i drove home. It didnt have power steering either. I did get one on it and wow you love the steering after that trying to parallel parking a boat hahahah. I am needibg to flush the radiator too. It overheated driving it 2 miles over here. . Since it sat 3 years im assuming that is it. Also the rear end i had to give it some gas moving it forst foot after sitting. Clunk ...it works now. So i guess the rear end needs oil grease etc. I was looking to see how to prove its rebuilt but i know it is rare for 200k miles on a 350 to not smoke. Lol.

@robertclarkguitar 10 ай бұрын

Oh she's typical too. Will smoke the tires and probably 8 ish seconds to 60 from dead stop. But the power is really there from 60 to 120. Hahah. I don't know what the guy did but assuming he bored it over 33 or whatever he said it's definitely not a stroker. It still has the stock parts as far as I can see. I asked him why didn't he dual the exhaust and put headers ...he said he likes to not draw attention. ?? I don't know but even if it wasn't rebuilt and was swell cared for I still got my 1800 out of it. And she still fires and drives.

@the_baderbuilt 10 ай бұрын

Sounds like a cool truck.

@davinhunt7558 11 ай бұрын

Looking to do something similar with my '98 k1500, subbed to see the end

@the_baderbuilt 11 ай бұрын

Thank you

@lloydstrayer4139 11 ай бұрын

Why didn't you add some electric jell to the coils?

@the_baderbuilt 11 ай бұрын

You are 100% right. To be honest with you it was a long day and I spaced it. I will be putting Dielectric grease on them

@phillipholmes4466 Жыл бұрын

Really enjoy your sense of humor! You have given me the bug to do a project. The problem is finding the right candidate truck. Thanks again!

@the_baderbuilt Жыл бұрын

I really appreciate that Thank you.

@paullaird7944 Жыл бұрын

That’s crazy

@robertsmith987 Жыл бұрын

what rust are you talking about lol u want rust my 99 silverado is swiss cheese

@the_baderbuilt Жыл бұрын

Hahaha it could definitely be worse for me. living in Arizona I'm not used to much more than surface rust. I have my fingers crossed for your truck lol.

@Bartmans_Garage Жыл бұрын

Good progress

@the_baderbuilt Жыл бұрын

I appreciate it. Thank you

@Generalpurpose702 Жыл бұрын

Thanks for the video, I will be doing the same tasks on my 1995 Chevy 2500, known as ol Waylon

@the_baderbuilt Жыл бұрын

You're welcome, Gotta love these trucks. Ol Waylon deserves it.

@Generalpurpose702 Жыл бұрын

@@the_baderbuilt yep, Ol Waylon had to be purchased, it was in much better shape than my 2000 Silverado

@scottmann3002 Жыл бұрын

Can't go wrong when the 25% coupon is used.

@the_baderbuilt Жыл бұрын

Not at all. Im very impressed with the quality of this wrench.

@ltwig476 Жыл бұрын

Nice clean work! I just purchased a 93 1500 WT 6cyl with 88,000 true miles, garage kept, zero rust. Just two little door dings on the passenger side. Wish it were Vortec. But I'm ticked to death with what I snatched up for $7,500. My new daily driver.

@the_baderbuilt Жыл бұрын

Awesome Truck. Congrats on your purchase!

Ең жақсы KZfaq

Пікірлер