Thanks for the walk thru. I think I can do it myself!

Thank you for such a great video.

What's the order

Thanks! Great video

Thanks for the Video. It took me 3 hours. Tools needed was Ratchet, 10mm,14mm,couple of different extension lengths, 5/8 spark plug socket, a magnet to pull out spark plugs,pliers for clamps and a flat head for clips

Thanks for share you do well

Good explanation about the belly button!

This is definitely the fix i needed. Thanks for the info

Great vid, if you change the motor mounts you should do a vid on that too.

A Men Bro, it is actually not a glue you are cleaning, it is Cosmoline. used to keep metals from rusting during over seas transport.

My dealer quoted me $1,100.00 for just a spark plug change on my 2016 Sedona lx. No coil packs just plugs. I did it myself and changed the upper intake plenum gasket since I was there. You can do this.

Great explanation and visual thank yoy hooe you make it big

I think god drives a Toyota.... I think your right, such amazingly well built cars, designed to be easy to service.

Would it be beneficial to do a smoke test on the intake manifold to make sure there's no leaks?

I'm Surprised That Alternator Started The Car...

Great job 😊

It took me two years to find it lol it’s not visible until you really investigate lt lol.mine was almost stalling when the rev reached 3000rpm.

Some mechanics removed the mount from underneath, with alot of trouble. Having to unbolt the carriage. I will follow your video to get my 2012 corolla rear mount replaced.

Did you use Toyota OEM mounts? I noticed the off brand don't last long. The rubber compound is not the same.

Presente en NAVOJOA Sonora México, excelente video, gracias por compartir

When did you unbolt the twin turbos? I keep missing that part and this is what’s holding me up.

Thank you so much for the video. Are they OEM toyota parts or after market parts? What do you suggest to buy?

Do you drop oil first . Before you change it

LOL, it's double layered bro! hehe.

What brand of shoes did you go with?

That shit was funny yo! I was entertained

You didn’t show to remove Ebrake line

I just changed all of mine on my Corolla . I did exactly as he said . Had no problems just the usual maneuvering of getting the bolt in some of the holes good stuff homie 👍

Do u remember what the mileage was on this Corolla? I have 297,000 mi on my 2009 Corolla and still no vibrations other than minimal textbook from a 4 banger. Thx!

When I replaced mine the engine moved. I needed a 6 foot crowbar to move my engine back into place to lineup the bolts to the boltholes. I think you got very lucky you didn't have to do that. Also a few of the bolts are very tight access and would have been nice to know that. It's not near as easy as you make it look

If fuel coming out of the exhaust pipe what do you think it could be the problem

Torque specs bro for the 14 and 17mm

Good and very clean job!

Cake thanks for the video informative doing this exact swap soon

So, you removed the mounting bracket from the engine FIRST and THEN pull the rear mount out after the bracket is off? I've seen videos in which they drop the sub frame down and move the exhaust over to pull it out from the bottom.

Am working on my 2013 corolla right now..i tried with a bolt on the 2 little wholes for the drum to come and nothing..drum keeps pulling out as i screw the bolts but at some point it stops.drum wont come out and feels hard to pull..i tried hit it with a hammer and they just wont pop out...any help..thanks

Mercedes specifies 17 lb/ft for the spark plugs which is approx. half turn after finger tight

Great Vid...

Excellent video, man! I like the way you removed the rear mount through the top, not through the bottom! It made me more confident now, as this one was the most scary for me. I'd definitely bring my car for you to do the job, boys, but driving it from Toronto (Canada) to Los Angeles is not practical. Best (and freezing) regards. 🇨🇦🇨🇦🇨🇦

Great video! Thank you, I’m going to attempt to do my wife’s van as well. 🤙🏽

It would have been helpful if you would have listed the brand and the size of the Sandpaper you were using. Then us newbies would have had a better chance of doing what you're doing. That looks like the right size and paper in many instances. Good video otherwise.

is this the rear drivers side or the passenger side

Torque specs for plugs? Torque specs for surge tank?

Thanks for this video bud. I watched it step by step as I did my wife’s van. You saved me some $$$. Cheers.

You look like my friend Pancho . Cool video

Aparte de chistoso well explained video! Thanks man!

from where did you get these brake shoes? hard to find the one with hardware attached!

Yo I just did the same fuel pump swap on my 94 pickup. I was inspecting all the work while my truck was running and the fuel pump seems decently loud, is that normal? Is consistent humming sound but I never noticed the fuel pump make sound before. Thanks for the video!

Hi can you share the link for the transmission that you bought

About to replace my gasket for my BMW