Пікірлер
@kbrownnn7420 Ай бұрын
Good video bro 🌟🌟🌟🌟🌟 + 🌟
@Derpherppington 2 ай бұрын
I build same as yours but mine got stuck when it got a little bit of lip left . I didn’t have a centering cone so I’m not sure if a little big off center affecting the last bit it did remove and put in the first lip fine. Does anyone trouble with low profile 17” tire. For 215 - 45 - 17
@TheTrevor1024 4 ай бұрын
Really don’t know how this makes it any easier, it faster just using the bar. Imo
@Mars-comedy 8 күн бұрын
Well you won't gouge the shit out of your rims this way
@duke792 6 ай бұрын
Are you selling these?
@anthonysalonek9462 10 ай бұрын
bearing race
@rodrigobarbirato1427 10 ай бұрын
do you sell this part separately?
@enricopolazzo33 10 ай бұрын
No, not selling these. Just a diy project I’ve shared.
@crazychickenfarm1475 11 ай бұрын
There is a tire in the way
@atifmuhammad47 11 ай бұрын
Idk if you read my comment but can you make one for me. They have no welding machine or welding experience. I know there are available online but they are expensive then the tool itself.
@bluemax229 Жыл бұрын
I've watched probably 50 videos on this type of duckbill accessory for the HF tire changer. Yours will be the one I make. If you knew me, you would appreciate that comment even more!
@enricopolazzo33 Жыл бұрын
Thanks. Note the angle is not necessary and I’ve just squared everything up in the more current version. But I think the materials I’ve listed will get you a really good result.
@markschulz1975 Жыл бұрын
Great video. Thanks for sharing. Is the tire machine bolted down to the floor?
@enricopolazzo33 Жыл бұрын
Yes some 1/2 inch concrete anchors with 3/8 bolts.
@inthelandofmilkandhoney457 Жыл бұрын
I like this design better with the sliding cross shaft and the angle adjustment. Wish I would have seen this video earlier 👍
@josegonzales777777 Жыл бұрын
Hello there is it possible you can make me one how much is gonna be
@still-DJ Жыл бұрын
That's the best working/designed mod I've seen on KZfaq. Great job Dan!
@ocmacman17 Жыл бұрын
Uhh, since there is no narration, can this thing do 19 or 20 inch low profile tires ???
@enricopolazzo33 Жыл бұрын
Narration is overrated. I think it would work
@jackpuskar1856 Жыл бұрын
Wow, looking forward to using mine. Thanks!
@Cheezeball99999 Жыл бұрын
That looked ridiculously easy. I've probably changed fifty tires on my HF manual changer, and fought every one of them. Scratched more than not. Goodness, I need this.
@sunnypepino Жыл бұрын
looks simple when you do it other not so simple
@sunnypepino Жыл бұрын
what angle is that duck bill mod is ?
@thomashorn9152 Жыл бұрын
What state are you in, maybe I could come by and pick one up in person..?
@cjespers Жыл бұрын
Well done, thanks for the video. Bought duckbill from your link. The angle you put on the duckbill is a game changer! Thanks again.
@gergemall Жыл бұрын
Where do you buy it ?
@gergemall Жыл бұрын
Brilliantly done and many thanks, I need to change several tractors ties , a travel trailer and some other one . Very grateful 😊
@acke26 Жыл бұрын
you dont need a duck head. best way to not scratch or damage the rim edge is simply to turn the rim upside down with the face pointing downwards. Just cut a hole in a rubber mat and place it on the top surface of the harbor freight tire changer. When working on the backside it doesn't matter if you get some minor scratches
@SevenFortyMotorsports Жыл бұрын
Nice, use lube though, raw dog can tear the sealing bead up.
@chipjumper Жыл бұрын
What gauge should the square tubing be? I'm looking online and I see the 1-3/4" square tube comes in 14ga (.083" wall thickness) or 12ga (.120 wall thickness).
@enricopolazzo33 Жыл бұрын
I use .120
@chipjumper Жыл бұрын
@@enricopolazzo33 I ended up just buying the $90+18 shipping kit from eBay. The materials to build this is about $50-60 (or like $5 if you scavenge a scrap yard). I don't have the time to gather the parts for cheap so I just bought the already-welded kit that's ready to rock. I still might entertain your design if the one I bought sucks.
@jamesdean5677 Жыл бұрын
@@chipjumper Which one did you get and how does it work?
@warrenwarburtonesq.6884 Жыл бұрын
In the comments, you have noted that you have made these that you sell. Are you still selling this duckbill attachment?
@enricopolazzo33 Жыл бұрын
Hi. Sorry not at the moment.
@mistersniffer6838 Жыл бұрын
Still selling the kit?
@enricopolazzo33 Жыл бұрын
Sorry not currently.
@trueitbycjtruitt9546 Жыл бұрын
Thanks brotha for marking the metal for me in my kit , it was very helpful, I noticed that yours has double the lock down bolts it it necessary to have ? Oh and wear did you get that little cone peice that goes down first before tightening the rim down
@enricopolazzo33 Жыл бұрын
Glad you’re happy with it. Just the one bolt is enough.
@SantaWoods Жыл бұрын
Absolutely ingenious, I know my next project thank you very much. I am mounting to my hitch receiver to free up space in my overcrowded garage
@enricopolazzo33 Жыл бұрын
I take no credit for the design. Glad I built it though as it’s been used a lot already. Note the angle is not necessary.
@larrynarvaez455 Жыл бұрын
Why did you put the duck bill tube on an angle? Is that a 45 degree angle?
@enricopolazzo33 Жыл бұрын
It’s only about a 15 degree angle but the duckhead is not on any angle. I had welded the flange on to counter that out. Angle is not necessary.
@rolandrepairvlog4420 Жыл бұрын
Amizing 👍👍👍
@JaydonRose Жыл бұрын
Clever design.. thank you for sharing.
@mickhallam1554 Жыл бұрын
What angle do you have duck head bar at. Many thanks
@enricopolazzo33 Жыл бұрын
It’s about 15 degrees but was unnecessary. The ones I’ve built since then had no angle.
@VinSpacker 2 жыл бұрын
Great video brotha! I encourage you to get outta your shell a little and speak, I know it's intimidating but hey, do it for the content! We won't judge you!
@kmadd818 2 жыл бұрын
Your mod makes it looks effortless, I noticed your tube is angled is that necessary for good results? Thanks for the link my duck Bill is on its way and at 13$ that's a steal!
@enricopolazzo33 2 жыл бұрын
The one I used in the video had the angle, but it wasn’t necessary. I’ve built and sold several after this one without the angle. The parts list in the description was what I settled on. Had good results with it. Good luck with yours
@johnbaptist7476 2 жыл бұрын
Hello friend Where did you get the duck head & the silver rod please . Thanks for response 🌾🌿🍀🍃
@enricopolazzo33 2 жыл бұрын
Hi. All materials are listed in the description.
@Travis32441 2 жыл бұрын
What machine is that. Starting road side assistance and I been looking around d for something cheap to start with.
@thatrandomproject6652 2 жыл бұрын
Smooth!
@robgonzalez4044 2 жыл бұрын
What is the biggest size tire/rim can you use to change on there?
@enricopolazzo33 2 жыл бұрын
I’ve never done anything larger than 18 but based on measurements it should work for a 22 with no problem
@Mikeyhoncho1 2 жыл бұрын
Hey Dan I am interesting in buying this kit. Let me know thanks
@enricopolazzo33 2 жыл бұрын
you can email me [email protected]
@rockyfjord3753 2 жыл бұрын
Your craigslist link says 'expired.' Where to get instructions for welding parts together?
@enricopolazzo33 2 жыл бұрын
I have one weld your own kit available to ship, in case you’re interested. I haven’t had time to put more together recently. I typically buy the metal from metal supermarkets.
@rockyfjord3753 2 жыл бұрын
@@enricopolazzo33 Thanks for offer; low on money at the moment, but may well like to get when I am able. Can I contact you through this YT channel? What cost for that kit, btw?
@rockyfjord3753 2 жыл бұрын
Prety slick. Where can I buy those additional parts?
@ericallen9038 2 жыл бұрын
The cut list in the description i think has an error, 1 3/8" tubing will not give you a sliding fit over the 1" tubing, you'll want 1 1/4" tubing with .120 or .122 wall.
@enricopolazzo33 2 жыл бұрын
I think it’s 1” schedule 40. I will double check, thank you
@arobjavan9481 2 жыл бұрын
Can this be used for motorcycle tires ?
@enricopolazzo33 2 жыл бұрын
No I don’t think so, but I’m pretty sure there are mods for the HF motorcycle tire changer out there.
@ronaldfutch508 2 жыл бұрын
That's great, and very professionally demonstrated, thanks for this helpful video.
@trueitbycjtruitt9546 2 жыл бұрын
if your planning on selling this setup how much would it cost , just curious 🤔
@enricopolazzo33 2 жыл бұрын
I have been selling the fully assembled unit for 165 and a weld your own kit for 75. Plus 16.10 shipping. Either option includes the duckhead. I’m currently only selling the weld your own kit. Don’t have much available free time to build them.
@trueitbycjtruitt9546 2 жыл бұрын
@@enricopolazzo33 that sounds like a great price, you use PayPal? If so I will order one tomorrow
@enricopolazzo33 2 жыл бұрын
@@trueitbycjtruitt9546 sure there’s a Craigslist link in the description you can contact me through there and I’ll send the info.
@dorsey1966 2 жыл бұрын
I've tried the Craigslist link and it says post has expired ? What now I want to buy a fully assembled unit please help
@bobmcl2406 2 жыл бұрын
This looks like an excellent but simple approach to improving the HF tire changer (Princess Auto up here in Canada). I really appreciate you having shared your build list too, as I see you prefer not to ship outside the US. Thank you!
@peaceblessingsall3889 2 жыл бұрын
👊🏾👊🏾
@1776FreedomNow 2 жыл бұрын
are you selling those? i dont have welding equipment. but i need that mod
@enricopolazzo33 2 жыл бұрын
Yes I’ve made and sold a few, but an updated design without the angled arm. See the link for the Craigslist ad in the description.
@1776FreedomNow 2 жыл бұрын
@@enricopolazzo33 yeah I can see the images. did you use something to center the wheel?
@enricopolazzo33 2 жыл бұрын
@@1776FreedomNow im using a bearing race to center the wheel and it seems to do fine. There are better centering cones on eBay.
@mrfoshobroful 2 жыл бұрын
@@enricopolazzo33 This setup looks really helpful thanks. I ordered a few parts based on your description. Would you have a description of a bearing race centering cone on Ebay by any chance?
@enricopolazzo33 2 жыл бұрын
@@mrfoshobroful I’m pretty sure the one I’m using is a front bearing for a 2004 sienna.
@Reloadeez 2 жыл бұрын
Alright we have came this far, who is the crazy sob that's gonna mount a gear and little electrical motor on this and make it semi automatic.
@LairdScooby 2 жыл бұрын
I did this to my own tyre changer in 2019, still working on the motor for the bar and also a bead-breaker on the bar - reckon i'll have to post a video when i do!
@Reloadeez 2 жыл бұрын
@@LairdScooby Please do, I have some ideas on how to do it but none that I like. I converted the bead breaker to a cheap 2 way piston air cylinder, makes breaking the bead easy, just pull lever and the piston breaks the bead.
@blackout7615 Жыл бұрын
The government will ban it if it becomes semi-automatic. Anything that sounds scary makes it a weapon of war and the people who choose a new gender will get their electric cars in a bunch worrying about how it will affect their next abortion.
@anthonysalonek9462 10 ай бұрын
torque multiplier