Thanks for sharing! I have the same one that won't turn on, so starting with the switch!

Same compressor, same problem. Thanks

Appreciate the video. You saved my sanity with your tip on the shims!

Thanks…nice video

Picked up one at a house clean up, same scenario, no power, did exactly what you did(used speaker wire tho, all I had) wahhlaaahhhhh, vrrrrrroooommmm...Thank you so much for my new to me mini compressor

The best video explanation of all the ones I saw . Thank you. You saved us a lot of money.

I still come back to this video when looking for lattice install.

Great video - especially how to insert spring back into place.

You’re a wonderful teacher!!

Thx homie...that did it😊

My brand new Samsung dishwasher won't drain never had this problem with bocsh.

Thanks. I never thought about expansion and cotraction.

My Samsung is not making ice do u have a video for that

may i know the same parts work for Samsung model RF28JBEDBSR?. thanks.

New subscriber here. I am learning ho to install a seal cock in my pump house wall Shark bite is an option for me. Just trying to evaluate long term affects such as leaks. All the best from north Texas.

Do you have to unplug the dishwasher ?

I live in Scotland how do I get one ??

I have the same model and noticed the water LED is not as bright as the ice LED - I have the same issue. Is this normal?

Informational, not instructional .

Great video great tips

Thank you so much!!! I had the exact same problem. To find the loose piece down the drainage tube drove me crazy, but I got it eventually!!!

I'm going to be turning my gate into a fence with a small gate

You didn't deburr your copper pipes, the Sharkbite o-rings will get damaged.

That's a very wide(8ft ?) fence gate; will it hold over time ?

Well shoot. I plugged mine in and it wouldn't start I checked everything. I finally realized that it was full of air and as soon as I started using it it kicked on. This probably would have been a better secret. lol.

Thanks! All I had to do was watch your video, return to the basement and as I was feeling around the switch to see if I could remove it, the machine turned on! Thanks again!

I grabbed a paper clip and now I'm drinking coffee!!! Thank you!!

Thank you so much! This is exactly the unit I had and exactly the same problem. I just took the switch apart and cleaned out the sawdust, reassembled, and it works perfectly!

Great tip. Thanks. I did same and it worked great

Great video. I just replaced mine on my Samsung refrigerator. The part that was the most difficult was what some others ran into... removing the control panel. Here is what I did: Remove the philips head screw. Put on a pair of gloves. Put as many fingers that will fit into the chute where the ice comes out, in front of the water dispenser tube. Grip only the black plastic piece where the ridges are at and not the smooth round chute part. Pull out and slightly down and it should come out. It took a good steady pull with some force (hence the gloves) and not a jerk. Again, the key is to grab only the black plastic with the ridges where the ice comes out. No other tools were necessary other than a small screwdriver to lift the tab on the power quick connect. To replace the spring: Look at the hole on the left side of where the new plastic panel clicks into. There is kind of what looks like a numer nine shape in black plastic. Inside the square shape, above and slightly to the right of the large hole, there is a tiny rectangular hole. That is where the long spring end goes. Put the spring on the new panel first, aligning the small end of the spring in the slot in the panel (you'll see it) then angle the whole thing so that you can slip the long end of the spring into that tiny rectangular hole and then insert the peg from the panel into the big hole. Then push the other peg on the panel into the opposite hole. Gently prying the plastic helps, but I didn't need to. You might hear a snap. If you do it right, the spring will sit exactly where it needs to be and the panel spring back when pushed. Reattach the power quick connect and snap the control panel back into place. Replace the screw.

Is this the Veranda lattice/cap products sold at Home Depot? If so, what color is this? Thnaks.

How about if there’s no clog or anything? Everything works no water pumping through the pipes

THANK YOU for posting this! I swapped a new one in about 5yrs ago and it just broke. Mind you, this is now a weekends only car. I said NO WAY am i putting ANOTHER one in....just like the damn cracked dashboard issues. Sheesh!

2024, apparently 10 years since your video. It worked! I just got this yesterday as a 2x hand-me-down (dad>Grandma>me) I didn't realize it was this old! I decided to run some vinager thru before using it. Lots of debris came out. Then it stopped brewing I thought I broke it😅. Of course it was the 10y/o debris that came loose and clogged the needle. Gracias from Mexico #My1stKeurig

Your camera is horrible and makes watching nearly impossible.

Can u increase tempersture

Thank u video was super helpful 😁

Awesome! Best video I've seen for this issue

This totally saved the machine. I guess when you open it, it gets a reverse drip with grounds which back flow into the machine. The grounds build up over time at a 45 degree turn. When I took the screws and pulled the needle cap, the whole thing came out. The needle cap is just attached (micro zip tie) to a silicone 45 deg elbow which then connects (secured by micro zip tie) to a hard poly tube running atop the head and then down the back of the machine. I was able to re-insert the needle cap. The elbow slipped back on to the poly tube with a little persuasion. There is no ziptie now at that connection though - you simply can't replace or re-fix a zip tie in that area. It's within the machine and impossible since there is no room. Still, without the zip tie the machine is running like new with no leakage that I can see. I am not worried, silicone retains it's shape and properties fairly well. No swelling on contraction Judging by the silly small amount of build up which prevented the machine from running, this a very low pressure system. All things considered, I am fine without the ziptie as I know it will likely not affect operation and this problem will happen again which will warrant future servicing.

It IS loud alright!!!!!

It was going great,until the music started. Please lower the volume.

Thank you for this! The pipe in my wall potentially busted during the freeze due to the outdoor spigot being frozen before I could drain it. Ive never done something like this and knew a lot would go into it. This video was very informative and gave me the confidence to attempt it on my own, thank you for not sparing any details as there is a lot that goes into homeowning and teaching someone should be equally as informational!

Thank you so much John, I ordered my part and you were great, wonderful detail. I was able to slow it up a bit for me and take some green shot snaps, because I would not be able to remember with all the interrupts in my home while trying to fix the level with all the small detail. Again, thank you so much!

Thank you for posting. I also have a shitty Samsung dishwasher and this saved me a lot of money. It was the rubber check valve. No one wants to work on these at all.

if you wet/sponge the edges of the tape it will seal so the stain won't bleed through on the edges. Let it dry before staining. I think that's why they call it frog tape.

Samsung has by far the worst fridges on the market

Sir one question what model number yours have. I would like to know i have one that it has a fuse that keeps blowing it, any thoughts on that Sir. By the way thanks for the tip how to check a switch.

Thank you!!! Worked perfectly.

I have to admit I was somewhat skeptical when you couldn't replace a handle whether you would be able to replace the faucet assembly without destroying your house.

Thank you!