Thank you sir

Backshots😩

Thank you this was easy to learn

brother than you got my master test tomorrow

Very well explain!

Terrible audio bud

Thank you so much for pointing this out. This exactly what I was looking for. Thank you again.

This is the easiest rod to read. Tenths and direct read rods make my brain hurt.

Hey thanks for this I know it was nearly a decade ago - but if you're still helping folks - this helped me :)

On a calculator, .42 × 16 = 6.72 round that up to 7, so that's 14 inches and 7/ 16ths for every foot of run

Thanks

How much

Now I understand how to read joist span charts in my IRC book! Thank you

Trick question: what is a one half pitch common rafter. Is it 6 x 12 or 12 x 12?

People at my work have the highest ego and make you feel dumb when you don’t get it at first but you definitely do know how to teach thanks boss appreciate the video

Are we going to just not account for the 1st stud at the edge that takes up 1-1/2 inch? This like the 3rd straight video I’m watching that is making the same mistake unless I’m not understanding something…

Thank you so much for explaining some of the chart and making it understandable. Looking for part 2 now.

Best I’ve seen 👍🏻

Finish this one lol. I could have payed better attention in class

One thing i notice is you are not conidering a top plate at the apex to calculate the run which woul be the run minus half the thickness of the top plate which then gives the correct run. That way you have something to attach the rafters to.

Thank you for doing multiplication the same way I was taught! Very refreshing! Thank you for helping me!

How do you read 524.59 on a grade rod ?

Don't you have to take off more then 3/4 if the slope rises above a 4?

Thanks for your clear explanation. I needed to find this out for my DIY project. One does not have to attend carpenter's school for some years to be able to enjoy building something. Even non carpenters like to build. We do not know all the details so we need help. You were open minded and unselfish in sharing knowledge and special thanks to you for this. The world needs more people like you.

4:26 No overhang discussed and won't be in this video. Video then loops.

Great demonstration-wish you would have continued down the framing square to show valley and jacks

Thank you for this

Now im ready to be pipe foreman

Thanks for sharing your knowledge. It is nice to know this

Thanks buddy that was so simple to understand,, to think how difficult ppl at work made it

Hey Mr Donnelly I have a couple questions is there any way you could message me email I really enjoy your channel

sooooooooooooooo confused

Po0pp0pp

Omg 1508

5968 not 5768

Great and straightforward description. As a complete novice I feel like most anybody could reasonably operate a brake with these instructions. Thanks for recording.

I look at the numbers and I get overwhelmed. I take a few seconds to see what .88 x 16 = 14.08 means and I realize 14/16s it's 7/8s. Then I think to myself: "was that it?!" I'm drowning in a glass of water

Thank you for this video it's helpful for me

I have a run of 15 and it will be on a 7 what is my rafter length

To the point and very easy to follow, instead of some complicated equations 👍

Cutting to mark?

Good Info, audio is way to low...

That was a great explanation. That totally helped me for class. dont see your over hang video.

Had no idea Robert Dinero knew how to do flashing

Just what I was looking for. Thankyou

Great video, so are b, c, d so on FS and we minus them?

Qual o valor da máquina ? [email protected]

Bend an I channel. 9 inch strip. Mark at 3 and 6. Bend 90. Roll and make a Z bend. Roll again and hem the Z bend. Roll again and form the J bend. Spin the part and repeat. 90, Z bend, hem, J bend.

Thank you🙂

Thank you, good information