General Principle

Пікірлер

@peteharrison9816 5 күн бұрын

I’ve been doing that for 45 years and balancing at home

@generalprinciple5921 4 күн бұрын

@@peteharrison9816 awesome.

@tombruce6398 8 күн бұрын

Dude you are the man great video for farmers like me thanks a bunch

@generalprinciple5921 7 күн бұрын

@@tombruce6398 I’m glad it could help!

@Bigfeats1337 15 күн бұрын

Ironically, I’m changing a tire on a 1968 case 430. I noticed your tire is quite wider than mine. What state are you in? Why is your tires so wide?

@generalprinciple5921 15 күн бұрын

@@Bigfeats1337 well I was in Florida and the tire were just on there when I got the tractor but were definitely too big.

@Bigfeats1337 15 күн бұрын

@@generalprinciple5921 That makes sense. Thanks for the vid. Used the backhoe to break the beads. Have one side half off now.

@generalprinciple5921 13 күн бұрын

@@Bigfeats1337 I take some practice but it totally doable. I had 16.9’s x24’s on my swamp buggy and had to do quite a a few out in the woods.

@Bigfeats1337 13 күн бұрын

@@generalprinciple5921 I bet that is fun. Assuming swamp + tire = muddy tire. I don’t mind the mud, but I would rather play in it than work in it.😉

@generalprinciple5921 12 күн бұрын

@@Bigfeats1337 yeah it was a great time in my life. Had a camp and buggy for 25 years.

@stephenhawkins6389 18 күн бұрын

Excellent

@generalprinciple5921 17 күн бұрын

@@stephenhawkins6389 I’m glad it helped.

@lorettaackerman4290 25 күн бұрын

Great video!!

@generalprinciple5921 25 күн бұрын

Thank you

@alexsbikesandmotors 25 күн бұрын

Last video stevie was 8 now he's 25 lol cool ski any way

@generalprinciple5921 25 күн бұрын

Thank you yeah it’s been a little bit since we posted

@justcatchem 25 күн бұрын

Sweet video!

@generalprinciple5921 25 күн бұрын

Thanks

@carlrudd1858 26 күн бұрын

You seem like a great guy. Next time record AFTER the wind storm. ;-)

@generalprinciple5921 26 күн бұрын

@@carlrudd1858 just the norm sometimes. But thx.

@derekmckay7397 27 күн бұрын

Now, I know I heard you advise folks to start at the stem side and move their way down - which is correct - but you didn't follow your own advice. Worked out ok, but visuals are everything to some people, and the risk to damage to the stem/core is higher not starting to seat/unseat tires at the stem. Otherwise, solid video!

@generalprinciple5921 26 күн бұрын

@@derekmckay7397 typical. Probably just wasn’t paying attention!1

@derekmckay7397 21 күн бұрын

@generalprinciple5921 happens to us all, brother. Folks don't give DIYers enough credit - a tire with a sidewall as tall as that tire you're removing is no joke to remove. You truly make it look much easier than it is...I just did a set myself today - it's not a fun job!

@generalprinciple5921 21 күн бұрын

@@derekmckay7397 it’s not to many that will put out the effort!!

@generalprinciple5921 15 күн бұрын

@@derekmckay7397 no it’s not. And thank you.

@rudolfyakich6653 Ай бұрын

Excellent to see Stevie in action

@generalprinciple5921 26 күн бұрын

thank you

@garybaker8212 Ай бұрын

This guy is great.

@generalprinciple5921 Ай бұрын

Thanks

@thesillybilly Ай бұрын

The wind in the video was almost unbearable. But thanks for the tips. You wouldn’t think that putting a patch on was that hard till you have to re-do one for the third time. lol

@generalprinciple5921 Ай бұрын

Glad it helped . Yeah I can’t control the weather.

@ThisIsNero-du8zg 2 ай бұрын

15:30 Lmao The finger waving "NO"' after the spin

@generalprinciple5921 2 ай бұрын

Glad you liked it 🤣

@bigboybuilder77 2 ай бұрын

Can you post whete you sourced the cvt transmission? I'm assuming the engine is from harborfreight?

@generalprinciple5921 2 ай бұрын

Yes sir it was eBay but all that is in the video I believe.

@lowcountryjeeper 2 ай бұрын

Thanks for this video! Need to patch two tubes

@generalprinciple5921 2 ай бұрын

Hope it did you some good.

@generalprinciple5921 2 ай бұрын

Glad it helped.

@Surroundedbyevil368 3 ай бұрын

I really like this idea thanks for sharing all of your Tech tips.

@generalprinciple5921 3 ай бұрын

Thanks

@Surroundedbyevil368 3 ай бұрын

Wow super cool really got the gears turning in my head and the little Gearhead looked like he'd been doing that for years.

@generalprinciple5921 3 ай бұрын

Thanks. Planning VW tdi swap for it next but the little Kubota,s been good though.

@user-rv3wi2sw8w 3 ай бұрын

took the air fuel piece out and didnt notice the spring right away, couldnt find where the hell its supposed to go. youre the man!

@generalprinciple5921 3 ай бұрын

Well… I’m glad it helped.

@alecmacpherson9838 4 ай бұрын

No ground reference on the AC side of rectifier?

@generalprinciple5921 4 ай бұрын

It’s been to long but I don’t remember. I’d have to look at it again.

@alecmacpherson9838 4 ай бұрын

@@generalprinciple5921 would you mind bro? It looks like you paired up the 2 wires on ac side to rectifier. And on dc side +ve to light and -ve to frame(GND)

@generalprinciple5921 4 ай бұрын

@@alecmacpherson9838 yes the ac from the stator went to the 2 wires of ac side of the regulator and the green wire was ground on the regulator and the red wire out went to the positive side of the light. That is all.

@EnglertRacing96 4 ай бұрын

Looks good but id never swap a real keihin or mikuni for a china clone.

@generalprinciple5921 4 ай бұрын

Yeah I wouldn’t normally either but it is a bigger carb than stock and I used oem jets I have had no problems with it. And I was a lot cheaper then a oem bigger carb

@EnglertRacing96 4 ай бұрын

@generalprinciple5921 ah well thats a good. In my videos, I've got a friend for your 100! My 1980 cr80

@generalprinciple5921 4 ай бұрын

@@EnglertRacing96 o sweet I’ll check it out

@RobertSmith-pi3lx 4 ай бұрын

I like the way you work with your son brother that reminds me when I was young and working with my dad

@generalprinciple5921 4 ай бұрын

Thank you! I only have one shot it so I’m gonna try.

@jodyprice420 4 ай бұрын

Nice vid. Look lot kooler if ya had a dual sport number plate light. That's what i plan do to my daughter 04 xr100r

@generalprinciple5921 4 ай бұрын

Thanks. my dad likes those.

@alb2571 4 ай бұрын

Would of love to do that with a son of mine! Glad you did

@generalprinciple5921 4 ай бұрын

I really enjoy doing this stuff with my son . It’s real gift from god. We just pulled VW 1.9l tdi to reporter this same truck. I’ll have get the video out. Thanks

@bike23august 4 ай бұрын

Can you explain again the woodruff key mod? So you shave 0.3mm from it to increase timing by 2 deg. But wont the flywheel have play in it after?

@generalprinciple5921 4 ай бұрын

They make an offset key but we’re impatient. So ground our own and turn the flywheel up against it and then torqued done the flywheel. It could move but hasn’t and son has really tried.

@waqaszafar8513 4 ай бұрын

Nice work both by dad and son. Cute little guy assisting his father, looks great❤

@generalprinciple5921 4 ай бұрын

Thank you but not so little anymore.

@MrBruce0777 5 ай бұрын

When you get the tire spoon and first start to get the tire off the rim most all people want to set the tire spoon real far away from the first tire spoon..I was so glad you showed to place the second tire spoon just a few inches away from the first spoon....Plus I found yesterday doing my tire that is the magic spot to get your tire spoon into it has a little type void.....Many thanks for showing a different way to remove the back side.... After 20 plus years of the tire being on the rim it is a fight battle to break through rust and severe tire stiffness.

@generalprinciple5921 5 ай бұрын

Good , I’m glad it helped!

@molobo1 5 ай бұрын

Just rebuilt a V2003T Kubota for the second time, My compression is low (about 260 PSI)and hard to start cold. All new rings pistons and standard bore sleeves, and had the head and valves pressure tested. How did you break in the rings?

@generalprinciple5921 5 ай бұрын

30w diesel oil, heat cycles of 10-20 minutes a piece then cool down. And 2 to 3 oil changes. Then good diesel oil.

@jimjenkins3226 5 ай бұрын

great that you include you son. Kids today seem to not know much of anything related to mechanical.

@generalprinciple5921 5 ай бұрын

Thank you . We do try!

@TheKuhner13 5 ай бұрын

Mine was missing the spring and flat washer on the fuel mixture screw. I re-assembled from a new kit in this order: spring, rubber washer, flat washer. Is this correct?

@generalprinciple5921 5 ай бұрын

No . I m sure it’s spring ,washer then o ring.

@TheKuhner13 5 ай бұрын

Thanks. I was able to change it easily. Also had to replace the cracked carb manifold and install the new idle needle. Runs pretty good now. Thanks for your help/video@@generalprinciple5921

@generalprinciple5921 5 ай бұрын

You bet.

@TRUBLU13 5 ай бұрын

Great job 👍🏼

@generalprinciple5921 5 ай бұрын

Thank you.

@TRUBLU13 5 ай бұрын

@@generalprinciple5921 no thank you helped immensely 👍🏼 been on a binge of your other videos great content

@generalprinciple5921 5 ай бұрын

Glad it helped.

@daysend1341 5 ай бұрын

Super awesome. I've been checking the channel Do you have any more updates on the truck? Definitely got my sub let me know if there's a finished video I'd love to see a dyno run on that. I know it's not crazy horsepower but the torque has to be great.

@generalprinciple5921 5 ай бұрын

Sorry no dyno runs but I’m sure with this indirectly injected b2203 it’s not making more than 35-38 hp but, it does 30 mpg can run 75-80 mph rung out but it like 45-60. I think there is a finished ish video out however I’m waiting on a manual injector pump for a VW 1.9 tdi I have and I’m probably going to swap it in sometime soon.

@vicosee4439 6 ай бұрын

Gentlemen my respect

@generalprinciple5921 5 ай бұрын

Thanks

@tubyou788 6 ай бұрын

Please what song in the start of the video . Thanks

@generalprinciple5921 6 ай бұрын

Simple man by lynyrd skynyrd always a good one!

@kmetyko 6 ай бұрын

Thank you. Really helpful. 👍🏼

@generalprinciple5921 6 ай бұрын

I’m glad it helped!

@dennisyoung4631 7 ай бұрын

Oh, one of the bigger engines.

@generalprinciple5921 7 ай бұрын

I kinda wish but this is what I had on hand and it’s not doing to bad except maybe could do a little better on mileage. Doing 30 mpg all the time. When time permits might do a VW tdi swap.

@dennisyoung4631 7 ай бұрын

@@generalprinciple5921 I meant,”one of the bigger Kubota engines.” Have seen a lot of smaller ones being used in vehicles recently.

@generalprinciple5921 7 ай бұрын

Yeah but it seams the larger ones are harder to come by on the used market and the v2203 is pretty popular.

@dennisyoung4631 7 ай бұрын

@@generalprinciple5921 no, meant 3 cylinder items of ~ 20 hp. The 2203 is about twice that powerful when normally aspirated, as well as having much more displacement compared to, say, a 722 or 903.

@generalprinciple5921 6 ай бұрын

Well the v2203 I have is an older indirectly injected one that made i think 33hp n/a.

@bartjohnson8139 7 ай бұрын

Congratulations on a successful build! My grandson and myself are about start an electric to gas conversion. I also was gifted a 48V cart with 8 deader than dead batteries. I had no idea how much batteries had gone up in price! So with that in mind, coupled with wanting mo power, well gas it is! We’ve got frame rust to contend with also. Our cart lived in Bolivar, Texas, at the beach. So rust rust rust! I’ve been pondering whether or not to do a complete axle swap, with an new axle assembly and engine tray mounted to a new swing arm frame or not, but man those $$$ are piling up! I was wondering how you managed the chain tension with your engine/transmission on a rigid frame mount going to a spring mounted axle. Thanks for sharing.

@generalprinciple5921 7 ай бұрын

I just copied a gas cart style engine tray and you also can build a spring loaded chain tensioner like a motorcycle if you feel the need to. Good luck.

@wyattwyatt3844 7 ай бұрын

That is awesome grate work looks good

@generalprinciple5921 7 ай бұрын

Thanks 😊

@istp1967 7 ай бұрын

Great video. And great way to spend quality time with your kids; teaching them some real useful life skills! 😁👍👍👍

@generalprinciple5921 7 ай бұрын

Well thank you. He’s developed more skill than I had at his age !

@ebutuoyebutouy 7 ай бұрын

Awesome. Long time no hear. Thanks for sharing. Happy New Year.

@generalprinciple5921 7 ай бұрын

Yeah sorry about the delay. Retired, moved states, remodel house, built new shop, moved parents, moved in -laws and bought an am remodeling a cabin. So be gust but we’re up and running ish.

@ebutuoyebutouy 7 ай бұрын

@@generalprinciple5921 Congratulations on your retirement. Good of you to take care of the seniors. Happy New Year.

@generalprinciple5921 7 ай бұрын

Thank you happy new year to you too

@justcatchem 7 ай бұрын

fmf sounds so much better

@generalprinciple5921 7 ай бұрын

O yeah I love the way it sounds

@richardmauch1042 7 ай бұрын

How does it do on the interstate?

@generalprinciple5921 7 ай бұрын

It does ok it will run 70 pretty good

@wyattwyatt3844 7 ай бұрын

😲😲😲😲is thare more videos to come glad to see a new post

@generalprinciple5921 7 ай бұрын

O yeah there is more to come

@galehess6676 7 ай бұрын

Can also use a skid steer bucket to break bead.., just press down with bucket edge. Tire spoons, sledge hammer. It's never this easy :) Maybe if I practiced more. Can run a ratchet strap around the tire circumference to push bead toward rim and minimize air loss if inflating with compressor. On the farm, we spray 2s starting fluid in the tire, out over the sidewall, light and step back.

@generalprinciple5921 7 ай бұрын

Yes sir I have done all that it’s never easy

@sebastienlapointe3820 7 ай бұрын

Add a capacitor to the DC circuit and your light won’t flicker as much

@generalprinciple5921 7 ай бұрын

Yeah I may have to do that thanks

@generalprinciple5921 7 ай бұрын

That’s what his dad told him.

@MarshallSmith27 7 ай бұрын

I just bought an 89 in remlap and got it home to tuscaloosa. looking forward to cleaning it up

@generalprinciple5921 7 ай бұрын

Good! We had a good time with ours.

@jcbenson01 9 ай бұрын

Brilliant tip on checking float level with the clear hose. 🍻🍻

@generalprinciple5921 9 ай бұрын

Glad you liked it!

@tomjungnitsch1965 9 ай бұрын

Do you have a parts list you used.. like clutches and reverse box.. I have a family heirloom cart just like that one you have

@generalprinciple5921 9 ай бұрын

Sorry for the late response. Lifan 6.5 hp electric start engine (predictor or Honda .their all Honda copies) the reverse box I got EBay 2, 10 tooth sprockets and a 30 series torque converter from EBay as well. I think that’s the majority of it. Good luck!

@rogertaylor1589 10 ай бұрын

What is the make & model of the reverse box?

@generalprinciple5921 10 ай бұрын

Weeeell…. it’s been too long to remember but I do remember I got it on eBay.

@taemian 10 ай бұрын

For those of us not living in the 1970s, the high side wall is pretty much a thing of the past, which makes this video useless in the modern age. Unless you’re putting bias ply on, of course. Must be a jeep thing.

@generalprinciple5921 10 ай бұрын

Ok cool. Sounds like you got it all figured out.

@lynskyrd 6 ай бұрын

this video is FAR from useless, I just did my nephew's 2016 Honda CRV using this guy's techniques. Why don't you just stick with helping your wife fold laundry. And to the guy that made this vid-- THANK YOU.

@harveyroad6 10 ай бұрын

Thats not your first motor rebuild. Sounds great. Are you going to do a video on repairing the cylinders.

@generalprinciple5921 10 ай бұрын

Thank you. I’ve done a few. No I’m sorry it’s done and sold and I didn’t even think about that. Sorry.

Ең жақсы KZfaq

Пікірлер