I used this product on my Lexus es300/2000yr - 310K miles.. fixed the slipping problem...

Can I come to you so you can do it for me

Did this fix work?

I noticed its a 5 pin relay but the relay socket only has 4 wires?

So same thing happened to my truck won’t start at all

So same thing happened to my truck won’t start at all

Excellent video Thank you much.

I'm looking to put one if these in my '16 ram and being able to see it in the bezel is exactly what i wanted, any updates on how its working out long term?

Would this work on a 2017 ram 1500, 5.7? I recently replaced the fuel pump worked for a week then truck stoped turning on. Fuel pump turns on I can hear it but truck won’t turn on. Had these codes on the truck P025A P062A Once fuel pump was replaced codes went away but truck doesn’t turn on, thank you

What gauge wire / type is needed for the hole? I plan on doing this soon. TY.

Well done. Great step by step and clear viewable video instructions. Thanks!

Did ours yesterday drill 1/8 hole clean it put short sheet metal screw in hole. And only snug it a little.

Am getting mad at the used car I bought.. after driving it for a month,it slips to neutral when driving it.its a Toyota auris semi automatic 07. I changed the fluid and it was normal. After some days , it happened again. I will need to off and on the car before it will engage again in the middle of the road. Am Even scared to drive it now. I took it to the mechanic and he checked and said he can't find anything 😢 that I should keep on driving it and if it occurs again I should bring it. Can Lucas do d job?

Sir I can kiss your ass. You saved me a lot of time. Need to do this to my dad's car and i never did one on GMC terrain before

clever.. maybe just tap the plastic intake and screw the screw straight in

We're could I buy the relay

What type of JB Weld did you use?

That is awesome. Got the chain. Just gotta find some pipe!

The problem with the 2.4L ECOTEC is the piston ring tension was too low. Nothing you have been would help. Except replacing the ring.

Awesome job, thanks for sharing this video

I did the 2 cam shaft position sensors or what ever they are called, the intake and exhaust and I also pulled the intake and clean the PCV valve and I have to add oil every other week. I check it every Sunday and sometimes it's low like 1/4 or 1/2 QT, but it is EVERY time. We need to find a good fox for this. So thanks for sharing this video. So you drilled a hole above the PCV valve so you can clean it when ever you want without having to take the entire intake manifold off right? Do you have a video on that process? Of drilling out the hole and setting the screw?? So you can remove the coil pack and plug and drop the B-12 Chem-tool directly down there??

If you are able to renovate this old car back to life, please do so. It will take a pile of work and heaps of money. Best wishes to the one who does.

Why do you keep saying the timing belt was changed? That engine uses a chain, not a belt

I have one and i love mine

If my fuel pump is priming, with the key in the on position, could the relay still be the issue? I just changed my fuel pump and it ran fine for a few days but now I have a crank but no start. Fuel pump is priming like normal but no fuel comes out of the line when disconnected from the fuel rail.

Hi nice video can i know you cut the wires or split from harness? Also you remove fuse of fuel pump in tipm permanently ? Its same wires on 2015 ram 1500 ecodiesel?

You sound like you would wait until the frame had rotted into 3 or 4 pieces and then spritz it with Rust Check on the way to the junk yard just so you could say "I told you so!"

How often do you expect to clean this hole? This orifice cleaning probably only needs to be done infrequently under most conditions, maybe just alternate oil changes, as long as it really gets done. I’d skip the JB weld. It’ll work ok on cleaned roughened surfaces, but is unnecessary here IMHO. Drill & self tap a tight #10 stainless screw right in there with locktite, and if it ever strips the plastic from R&R-ing, tap in the next size. OR if you eventually must re-tap too big, then result to JB weld as necessary. Just get really clean, roughened surfaces.

I thought that the oil control rings were stuck and letting oil go past into combustion chamber on the Verano, equinox and terrain 2012-2017 ?

Yes i would keep it

Will this work on a 2015 equinox?

Instead of JB Weld and a nut, Just use a rubber plug in the hole you drilled

May 11 6:00 am I can clearly hear you say 86 is sliced to brown wire but in the video it looks like it’s just connected to brown wire that goes to black connector in fuse box. I don’t see 2 brown wires in the splice Please help

May 11 6:00 am Looking @ video Is the brown wire spliced to 86 or just connected to brown wire that goes to black connector in fuse box I don’t see two brown wires in the splice Please help

9:15 am May 10 Would this apply to 2015 ram 1500 as far as the colour of wiring goes My fuse box looks exactly the same as yours & the fuel pump fuse is in the same location

Don’t crap your equinox JB it I got JB weld and duct tape holding my Chevys together 😢😅

Try using Yamalube Ring Free Plus shock treatment of 1 ounce per gallon of gasoline.

I wish you had shown how you put the bolts back. That is a lot of money to spend for one bolt. I was not taking it to a shop though. My battery is charging. My Harbor Freight was out of the single battery, battery chargers. No other Harbor freights close enough to spend the time and gas to go travel where there was a store that had one in stock. I hope they aren't selling these out for another line of tools and ending this line of tools. Something I have seen them do before.

Boy como adivinaste que estába el hoyo de pcv ahí exacto?

Could you have used a silicone plug instead of the JB nut/setscrew?

Putting your daughter in there was cute plus I love learning about fixing my daughter's car.

My friend thats for this video youve saved us alot of money in the long run

With that big of a tractor it should pull them out without a problem. Going to make one for our Kubota B2620 to see how it works, Nice video.

Putting a 3 or 4 ft tall, upside down T made of 4x4's or even just an old tire on a wheel under that chain/rope will allow the pulling force to lift the tree/brush upward instead of horizontally across the root system. Anything with a well developed tap root can put up a good fight either way.

Great, innovative fix for a design flaw. Good work. thanks for sharing.

Well don t know why you cut the chain . Not the way I saw it done

This is a creative and useful video. I live in FL have a 2017 I bought new but now has 100K plus. I noticed some oil consumption issues and this issue sparked my interest in maintaining the car myself because I need it to last. My intake was full of oil, plugs had oil on them etc. While I cleaned the intake, your video showed me that I need to take the time to “vac out” the bottom of the manifold and more importantly you came up with a plan to be able to prevent the problem repeating, which I am very appreciative of.

Where did you purchase the part?

chevy announced a bs quick substitute fix… they suggest you buy an oil cap with a pressure relief valve in it to save the rear seal from blowing out. I bought it.. but my oil always smells of heavy gas and its always black. gonna have to do this trick for longevity purposes. and my oil filter is always caved in on itself.

Great video I have the exact same problem