Thanks sir for the pratical, I'm definitely sure it will help a lot of students including me.
@mrwise131527 күн бұрын
I am elated. Try and share the video and subscribe. Thanks
@patrickokpitan647528 күн бұрын
Neco didn't ask for metre bridge
@mrwise131528 күн бұрын
Yes they asked of constantan wire which can be Potentiometer or meter bridge. So any1 can serve
@patrickokpitan647528 күн бұрын
The voltage increases with length because of the cross sectional area. The cross sectional area of the Constantine wire in the meter bridge is different from the SWG26 Neco give
@mrwise131528 күн бұрын
The Constantine wire is not a problem. The main thing is to know how to connect the circuit.
@StellaJeremiah-js3crАй бұрын
Great.keep it up
@mrwise1315Ай бұрын
Thanks. Share my video and subscribe
@anitaovos339Ай бұрын
You have shown how you attached the pulley
@mrwise1315Ай бұрын
Is very simple. I used nail to hold it on the board
@Idoko_IfeanyichukwuАй бұрын
What's the current used in your experiment?
@mrwise1315Ай бұрын
I used voltmeter. No Ammeter in the experiment. So is the voltage that i am reading. Thanks.
@OlawaleMuhammed-oy8gyАй бұрын
Understood nice job
@temitopeoke9764Ай бұрын
There's something not clear to me, those lines you drew on the white paper, how do you come about it. Thanks.
@mrwise1315Ай бұрын
I used pen to rule it. The line obey equilibrant force
@AdepojuFaith-d2fАй бұрын
How ? I don't get it
@mrwise1315Ай бұрын
Go and read about equilibrant force. You will understand the diagram.
@ashayhemy3617Ай бұрын
Which principle of physics does this obey?.... Thanks for the effort but I don't think the experiment will be based on that... It has more to do with machine
@mrwise1315Ай бұрын
They is no principle attached to it. Is just equilibrant force
@daviduc7573Ай бұрын
Great work. But check the instruction given to teachers, the mass on the pulley should be 30g labelled W
@mrwise1315Ай бұрын
The fixed mass is not constant. So i can use 30g or 40g or 50g as the fixed mass depending on the question.
@enenchesunday2925Ай бұрын
Sharp and clear work!
@mrwise1315Ай бұрын
Thanks alot. Try and share my link and subscribe
@Jenny-256Ай бұрын
Nice one
@mrwise1315Ай бұрын
Thanks
@mrwise1315Ай бұрын
Don't forget to share the video
@mrwise1315Ай бұрын
Don't forget to subscribe Thanks
@AlphaProZambiaАй бұрын
Next time be in a quiet place 😢😢
@mrwise1315Ай бұрын
The place was a serene place
@AlphaProZambiaАй бұрын
GREAT ❤❤
@mrwise1315Ай бұрын
Thanks. Try and subscribe
@mrwise1315Ай бұрын
Don't forget to subscribe
@mrwise1315Ай бұрын
Don't forget to subscribe. Thanks
@mrwise1315Ай бұрын
Don't forget to subscribe
@mrwise1315Ай бұрын
Don't forget to subscribe
@mrwise13152 ай бұрын
Don't forget to subscribe
@mrwise13152 ай бұрын
Don't forget to subscribe. Thanks
@aondoaseerstephen61382 ай бұрын
My brother it's not advisable to use odd numbers cos
@mrwise13152 ай бұрын
You get your scale from your table. Very simple. You don't forg scale or assume it
@ezeugochi99112 ай бұрын
😊
@mrwise13152 ай бұрын
Don't forget to subscribe
@chrisapathy62022 ай бұрын
the deflection of my galvanometer is only in one direction what could be the cause?
@mrwise13152 ай бұрын
Check you connections again. Your connection is wrong
@splendidforum43532 ай бұрын
Thank you sir
@mrwise13152 ай бұрын
Dont forget to subscribe. Thanks
@mrwise13152 ай бұрын
Don't forget to subscribe
@user-hb4tk8eg2o2 ай бұрын
Wowwwwww
@user-hb4tk8eg2o2 ай бұрын
Great
@user-hb4tk8eg2o2 ай бұрын
Impressive
@user-hb4tk8eg2o2 ай бұрын
Cool
@user-hb4tk8eg2o2 ай бұрын
Nice
@PhysicsWithBen2 ай бұрын
Well done Sir. On point.
@mrwise13152 ай бұрын
Don't forget to subscribe
@mrwise13152 ай бұрын
Don't forget to subscribe. Thanks
@mrwise13152 ай бұрын
Don't forget to subscribe. Thanks
@faidahadeoye6532 ай бұрын
After the connection, the galvanometer deflected at both ends, but I didn't get a balance point on the galvanometer i.e the deflection was stationary on the galvanometer. Please what should I do?
@mrwise13152 ай бұрын
It will definitely reach the balance point. Hope you are moving the jockey from 0cm to get your balance point with that it will balance. But if you are moving it from 100cm it will not balance
@mrwise13152 ай бұрын
Try and subscribe
@bukkyakinlabi79072 ай бұрын
Bravo, how can I get the procedures to the practical?
@mrwise13152 ай бұрын
@@bukkyakinlabi7907 is on the video.
@udemejohnson9602Ай бұрын
Sir pls from what year did they get the question sir tnx sir I like your teaching
@mrwise13152 ай бұрын
Don't forget to subscribe. Thanks
@mrwise13152 ай бұрын
Don't forget to subscribe. Thanks
@eseyinoluwakemi4190Ай бұрын
My connection isn't working
@mrwise1315Ай бұрын
@@eseyinoluwakemi4190 . Check the connections again or you need to check the apparatus that you used
@eseyinoluwakemi4190Ай бұрын
Thanks so much sir
@mrwise13152 ай бұрын
Don't forget to subscribe. Thanks
@mrwise13152 ай бұрын
And i left it where the maximum current was achieved before starting
@mrwise13152 ай бұрын
It was adjusted before i started the experiment
@KennethBegold-jp1mw2 ай бұрын
Was that ur preferred condition?
@mrwise13152 ай бұрын
@@KennethBegold-jp1mw Yes. But after the connection if they is no deflection on both side,you need to adjust it and check again.
@KennethBegold-jp1mw2 ай бұрын
The rheostat was not adjusted at any time..does it mean u left it at a point where u get a maximum current