Thanks a lot for the video! With mine the delay got that bad that the speakers wouldnt turn on at all anymore. Swapped the capacitor and they are working like on day one again!
@producerdiaz18069 күн бұрын
Hi hello i have a question I was given the left sode if e4.5 and when I plug it in and power it on the blue power light won't go on and and makes a rapid pop noise donyou have any clue on where thr problem may be ir where i could start looking? I pulled out the amplifier but i don't see anything that looks out of place. Thank you in advance!
@FixYahTv9 күн бұрын
@@producerdiaz1806 i have another video similar to the problem you are having.. check it out on my channel.
@producerdiaz18068 күн бұрын
@@FixYahTv what's the link if the video or title? I wanna make sure I'm watching the right one.
@chetvoxx9 күн бұрын
Galing Sir. I found your video during my search. I have a 16.4.2 that doesn't have input signal. Do you know which can be the problem? I also have 24.4.2 , this one , channel 5 has no input signal. AND, the board doesn't have Audio output. No Sound going to the speaker. Can I ask for your expertise. Salamat.
@FixYahTv9 күн бұрын
@@chetvoxx about sa 16.4 2 na ka hang ba ang GR nya? If so subukan mo muna ifactory reset using old version of macbook dun lng kasi sya gumagana. Di kasi sya narerecognized ng mga new version.. then iupdate mo yong firmware sa pinakamababa hanggang pataas.. dapat walang laktaw. Pag di parin umobra try to replace the 3 pcs 5volts regulator sa DSP.. if wala prin it means DSP is defective na.. about nman sa 24.4.2 nman.. its a Pre-amp issue.. may SMD resistor dyan n 100 ohms malapit sa potentiometer baka sunog na kaya walang signal napumapasok .. pwd rin yong amp ic nya ang sira sa ch.5 ang may problem.
@chetvoxx9 күн бұрын
Salamat ng marami. Hindi ako marunong ng electronics pero susubukan ko. Unahin muna yung 16.4.2. Binuksan ni misis just to look inside. Do not see any leak sa capacitor. Yung pang update ng firmware siguru muna ang gagawin ko. Then factory reset ko. Thank you
@user-bm1lo7cb8q17 күн бұрын
My Eris E4.5s. stopped working after a short power cut. Appears to be the same damage. Too expensive to return to manufacturer and pay for the repair. Not worth fixing. I wonder how many have had this problem?
@dmitria684714 күн бұрын
Experienced the same the day before Yesterday in central Europe, so I can feel your pain ) I was searching for repairing instructions, but then, watching this I decided to save my nerves and time. This is obviously a Design flop of PreSonus. I also Googled a bit and yes, we are not alone. PreSonus rolled out and advertized the 2nd Gen, where they put a glas fuse in the box. So, this might seem as rework, but they basically mean by that, that the problem may pop up again (and this is halfway a temporary solution). Not good. One might want to look for something else.
@cycobeez22 күн бұрын
hi can you fix fire wire issue studio live 16.4.2. GR meter full red
@FixYahTv22 күн бұрын
@@cycobeez try to modify your board by replacing the 3 pcs 5volts regulator with 7805 regulator..
@cycobeez22 күн бұрын
@@FixYahTv thanks man. can you make a video of it? a lot of people will be happy
@leandretanph23 күн бұрын
sir pwede ko din paayus un ganyan ko
@FixYahTv22 күн бұрын
Just contact Modular Display Inc po sir.
@tommyviolinistfromcabo693126 күн бұрын
Saludos desde Mexico. Mio no suena solamente en audífonos me parece que se daño tda 8920cj que es la salida de amplificadores
@arthurbautista325227 күн бұрын
Sir gumagawa ka ng module ng das audio monitor?
@ortakehinfatronardolewvidurel29 күн бұрын
same here, the lowESR 1000uf caps were fat, waiting for some new ones to arrive...
@ortakehinfatronardolewvidurel29 күн бұрын
I'm here learning repair and tagalog...my eris4.5 suffered from bad caps, anyone who takes the back off should use the oportunity to swap the 1000uf 25v caps(2) as I've seen a few go bad.
@HOALANTHUCLEАй бұрын
Giá nhiêu
@victorborgaily9976Ай бұрын
How did you get the parts? I have exactly the same unit with that problem? Contact info pls?
@pepzisko13Ай бұрын
Sir saan po ang exact location nyo baka po pwede magpagawa nalang sainyo. Salamat
@FixYahTv29 күн бұрын
@@pepzisko13 just contact modular display inc..
@DanteWilliams728Ай бұрын
Is this board good as the Allen & Heath SQ 6? I’m trying to decide which one to get. Thanks.
@yairaristabaez218Ай бұрын
Can you do one about the lcd screen not working.
@paulrichards3928Ай бұрын
Who sells switches, for this model?
@FixYahTvАй бұрын
RS components.
@paulrichards39289 күн бұрын
@@FixYahTv Thanks. Raises one question. No catalogues, show, the switch back image with 4 pins. Is this the switch type? DP ON - OFF Cat no. R13 244A AAA docs.rs-online.com/af05/0900766b808a97c8.pdf
@user-kv5oi3vo7bАй бұрын
Hilo po mayron kau na fb kc maron sira na presunos..
@FixYahTvАй бұрын
@@user-kv5oi3vo7b anong unit sir?
@user-kv5oi3vo7bАй бұрын
Presonus Studiolive 16.0.2 po sir
@user-kv5oi3vo7bАй бұрын
@@FixYahTvpwde po ba makahingi messenger sir, para ma send ko po video sa presonus ko sir para makita mo po yung deffect nya
@FixYahTvАй бұрын
@@user-kv5oi3vo7b ano sir messenger nyo ako magpm sa inyo.
@user-kv5oi3vo7bАй бұрын
@@FixYahTv Shable Jayn po sir
@r2d2romo1Ай бұрын
Tengo el mismo problema con un modelo sceptre S6. En la PCB veo ligeramente sobrecalentado las terminales de un capacitor de 680uf a 50v, ¿podría ser el problema? Es un capacitor de la serie FC, solo que no he encontrado un datasheet para ver su tolerancia y ESR
@FixYahTvАй бұрын
You should also check the LF driver ..
@r2d2romo1Ай бұрын
@@FixYahTv sí, caray. Está destruido el imán del woofer :'(. Sabes si ¿presonus vende refacciones?
@user-kv5oi3vo7bАй бұрын
May facebook po ba kayo sir?
@FixYahTvАй бұрын
Modular Repaird Dept. dito nlng po kayo magmsg sir.
@2160pАй бұрын
hello, can you explain how to fix scratchy volume knob?
@FixYahTvАй бұрын
You have to replace the volume potentiometer if the volume knob is scratchy.. the part no# of the potentiometer.. RK097G 10K 6PIN variable Resistor rotary carbon film taper Potentiometer.
@2160pАй бұрын
hi can you explain what to do when turning the volume knob causes crackling?
@FixYahTvАй бұрын
The problem when the volume causes crackling is corrosion over time. Wear and tear from constant use.. to fix it is to replace the volume potentiometer..
@jenifercabulay6175Ай бұрын
Bossing pwede malaman address ng shop niyo ipapagawa ko nga ang aking presonus 16.4.2 . Thanks
@FixYahTvАй бұрын
Modular Display Inc po..
@jenifercabulay6175Ай бұрын
Bossing pwede malaman address ng shop niyo sa Q.C. May presonus kasi ako na 16.4.2 na no power on.
@FixYahTvАй бұрын
Pm nyo po ako sa facebook.. Modular Repair Dept.
@jenifercabulay6175Ай бұрын
Thanks you
@elgenendig59742 ай бұрын
No sound po ang prblem
@FixYahTv2 ай бұрын
Check for speaker bka nasunog pag ok mman.. replace TDA ic.. yong nkakabit sa Heatsink if present ang power..
@yxngxkidd2 ай бұрын
Where Should I find That Capacitor Please Help I’m from India 🇮🇳 please Help
@FixYahTv2 ай бұрын
You can order it on RS components online.
@mightymightyironhead2 ай бұрын
Thanks for making this video. I have the Eris 4.5 and they have been acting strange for a while now. At first there was static when i turned the volume knob, then they started to take time to power up, maybe 5 minutes before the blue light came on and i can hear sound through them. Now they have started to not power up at all some days and if i leave them, maybe they will power up the next day. I searched around and a lot of people have the same issue with these speakers and i had a good idea that it was the capacitor, after watching your video i am more sure about that.
@FixYahTv2 ай бұрын
I'm glad my video was helpful😊
@StoriesOnWheels92 ай бұрын
Can you please share details of the switch- how many amperes, voltage etc - i am finding one which is 4 pin rocker 6A 250V AC DPST ON-OFF Black Round Rocker Switch....is this a correct replacement. Many thanks.
@FixYahTv2 ай бұрын
its 4Pin 6A 125/220V AC DPST ON-OFF Rocker switch Snap-in.
@StoriesOnWheels92 ай бұрын
@@FixYahTv is it ok, if it's 250v. Not finding 125/220v?
@FixYahTv2 ай бұрын
Yes sir.. its ok..👍🏻
@slumber71832 ай бұрын
Hello. Thanks to your video, I found the cause. Thank you. Can I use spst instead of dpst?@@FixYahTv
@FixYahTv2 ай бұрын
Use only DPST switch for safety.
@Logiser2 ай бұрын
Exactly the same problem, thank you
@FixYahTvАй бұрын
Glad it helped
@sabrinarebh3382 ай бұрын
Its not the switch for me 😭
@FixYahTv2 ай бұрын
Try to watch my other video😁
@Logiser2 ай бұрын
I have a problem that my speakers make a popping and booming sound, regardless of volume pot
@FixYahTv2 ай бұрын
Check my other video 😉
@rossdaveyentertainment2 ай бұрын
Wow. That can't be more than 5 years old and it looks ancient. Build quality? Or misuse?
@FixYahTv2 ай бұрын
Misuse it is 😢😭
@JMTransportServices2 ай бұрын
Sir pwede po makahingi ng exact address & contact# po ng shop nyo? mahina po kasi output ng right ch ng 24.4.2 na unit namin,, dalahin po namin dyan..
@junardtucker3 ай бұрын
Where can I get the lcd to buy?
@FixYahTv3 ай бұрын
You can only get it on presonus authorize service center..
@gyangjisik3 ай бұрын
Thank you. The symptoms were the same in the same model as the video. I saw this video and fixed it.👍😍
@FixYahTv3 ай бұрын
Glad to be of help.. 😁👍🏻
@FixYahTv3 ай бұрын
I hope you also support my channel.. thank you😁✌
@nikkimariano71354 ай бұрын
Boss tanong lang pag gumagana naman pero nawawala wala yung sounds ano dapat checkin?
@FixYahTv4 ай бұрын
Check mo sir mga connection, minsan lumuluwag dahil sa vibration. Check for bulging capacitor.. check mo din sir yong TDA ic bka nagooverheat.. lagyan mo ng bagong thermal grease. Check mo rin yong speaker if good pa bk mababa na sa 4 ohms. For now yan muna sir ang mga dapat mo icheck.. sana makatulong..👍🏻
@ashiqahamed77404 ай бұрын
Hello! I’m having a similar problem in my eris 3.5 just going around KZfaq looking for fixes
@FixYahTv4 ай бұрын
What seems to be the problem?
@ashiqahamed77404 ай бұрын
@@FixYahTv similar to this actually, my active speaker, left side was not giving loud output like passive speaker and then yesterday it just stopped giving output. To make sure it was isolated to left speaker I removed the red/black connector wires and played audio only in left, It was playing audio with very small soft volume even with volume knob turned to max. If it’s anything similar to the problem in this speaker I suspect it must be a blown capacitor, sir
@FixYahTv4 ай бұрын
Try to replace bulging capacitors. Sometimes capacitor leaks and causing weak and sometimes buzzing noise.
@GrimYak4 ай бұрын
San shop mo sir? may nag ganyan akong issue pero nung tumagal di na talaga nag on. yun lang pag iniinit ko yung power IC gumagana naman ulit pag hindi mo tinanggal sa saksakan. pag uwi ko sa bahay test ko yang cap na yan. napalitan ko na rin yung 2 25v 1000uF kasi bloated na.
@FixYahTv4 ай бұрын
Novaliches QC po sir..
@GrimYak4 ай бұрын
@@FixYahTvthanks! Texted the number. You dont fix the 3.5 daw, palit daw. Thanks na lang.
@FixYahTv4 ай бұрын
Saan nyo sir nabili unit ninyo?
@GrimYak4 ай бұрын
@@FixYahTv I brought it with me from the US. but that should not matter. I have an MR4 on order which based on reviews is better than the Eris =.
@FixYahTv4 ай бұрын
I see.. kaya po pala di nila tinanggap yong unit ninyo kasi di nabili dito sa pinas.. ang tinatanggap lng po kasi nila is yong binili sa mismong supplier dito sa pinas. Pasensya na po pero i hope my video help you fix your unit po..
@frandyjoseph28704 ай бұрын
Hey can you show me a place to go where I can buy the fuse please
@FixYahTv4 ай бұрын
You can order online.. T 3.5A.
@frandyjoseph28704 ай бұрын
@@FixYahTvthank you so much keep up the good work
@jaztal48594 ай бұрын
Hi, thanks for video, I'm currently using Presonus Eris 4.5,and it has a not loud but very noticable static hum sound, and I searched the presouns forum but not really helpful. Can you tell me if I should open it and replace some parts?
@FixYahTv4 ай бұрын
If your unit is under warranty you should send it to your supplier but if itis not. Try to replace bulging capacitor near the TDA ic.
@estebansuarezmarenzi11354 ай бұрын
I have the same problem in my Fender Champion 40. I will check for cold solder points tonight. Thanks for sharing!
@FixYahTv3 ай бұрын
Did it work?
@warblo5 ай бұрын
Same thing happened to mine. Ah man, this is annoying
@warblo5 ай бұрын
What would of been great if you had the whole video unedited. for me to watch. As i haven't done this kind of thing before. do you still have the whole video?
@FixYahTv5 ай бұрын
Sorry man.. i dont have it anymore.. just replace all the bulging capacitor and thats should fixed the problem.
@warblo5 ай бұрын
@FixYahTv no worries man. Just wanted to see what you used. I noticed you put some brown liquid around the capacitors. What is that? Also, you used something to glue the foam back on. Things like that would be really helpful to know.
@FixYahTv5 ай бұрын
You can use RTV silicone adhesive.
@warblo5 ай бұрын
@@FixYahTv thanks man
@Fabioaria5 ай бұрын
Which is the model of the Display, please ?
@FixYahTv5 ай бұрын
Thet are called SL 1642 LCD 192x64. But you can order it on your Presonus supplier only.
@Fabioaria4 ай бұрын
@@FixYahTv thank you
@stagelifeeventmanagement48585 ай бұрын
Hi dear I have a problem my 32ai presonus last 32 Channal have no audio after input
@FixYahTv5 ай бұрын
Can you gave me more info about your unit?
@stagelifeeventmanagement48585 ай бұрын
Ya sure Yes, yes, man, once it happened that I was in a show and there was a problem of power fluctuation, the earthing was very high, so I was checking the income with the tester, and by chance, the auxiliary input was in the wrong channel. On the channel number 32, as soon as I put the tester on it, it has shorted the negative and positive, so a slight spark and the IC of the channel went off.
@stagelifeeventmanagement48585 ай бұрын
@@FixYahTv If it is possible that the input of that channel is actually when I plug it in, then the gain and its cue are running but the input is not inputting in that channel. The input is not working and there is another problem when today it happened. As soon as I do it, it is 32 by 32 channels. So that is probably a grounding problem
@delumario5 ай бұрын
Hi there, I had the same problem diode and transistor burned. I did the exact in the video and changed the components but the diode still burning. Any idea for the next step?🙏 Thanks
@FixYahTv5 ай бұрын
check also large filter capacitor for short or leaky.
@BonkeyMucket5 ай бұрын
I just got one of these and love it, but I also wanted to see what to do if the power goes out on it. Thank you.
@FixYahTv3 ай бұрын
Enjoy it
@renerioordeniza65825 ай бұрын
Hi sir hingi lng po ako ng tulong at advise sa inyo about sa presonus ko 16.4.2 laging SDRAM SELF TEST FAILED at at totally wala nang audio sound ano po kaya ang problema nito po. Salamat
@FixYahTv5 ай бұрын
Nagfirmware update po ba kayo at natapos po ba yong update?
@epaschenko5 ай бұрын
How to disassembly passive speaker?
@FixYahTv5 ай бұрын
Sorry to say but it is permanenty closed.. they put strong adhesive to close the speaker.
@epaschenko5 ай бұрын
@@FixYahTv A very strange decision. I think that in my copy there is something with a separating capacitor, because the high frequencies sound more muted than in the active one. At the same time, the output from the amplifier produces the same signal, I checked it with an oscilloscope.
@FixYahTv5 ай бұрын
You can check the back of the passive speaker and gently priy the speaker connector.. its has a capacitor in it.
@LeeFordDiYs5 ай бұрын
Sir may fb po kayo? Yung 16.0.2 ko walang input signal. Papaayos ko po sana. Leeford Planas
@FixYahTv5 ай бұрын
saan nyo sir nabili ang unit ninyo po?
@LeeFordDiYs5 ай бұрын
@@FixYahTv sa US po. After ko mgconnect connect sa computer FireWire sa universal control wala napong input signal lahat channels.
@LeeFordDiYs5 ай бұрын
@@FixYahTv second hand po nabili. All working naman po after recently lang wala ng signal lahat channels. Aside from that all functions working po.
@mavick25255 ай бұрын
Hello po sir. Sana ma pansin nyo po. Meron din po akong Presonus Eris E3.5 Ang issue po is nag cacrash po yung tunog nya, like distorting after some time of usage. Lalo na sa mga bassy na music. Pero kung bagong On palang po. Hindi pa. Dun palang sya mag sstart mag crash kung makatapos nang 1or 2 songs.
@FixYahTv5 ай бұрын
Leaky capacitor po ang problem ng unit ninyo.. replace nyo lng po yong mga nagbulge na capacitor and that should fix your problem po..
@mavick25255 ай бұрын
@@FixYahTv Ok po sir. Salamat.
@LeeFordDiYs5 ай бұрын
Hello po. Pano po kayo contactkin? Meron po kasi akong 16.0.2 bigla nlang humina yung output ng mga channels half yung volume compare nung ok pa. Thank you po. Parang naoverheat po may ulan po kasi tas tinakpan ko yung mixer Hindi nman po pinasukan ng tubig .
@FixYahTv5 ай бұрын
Check mo muna sir yong master fadee nyo.. try nyo sprayan ng fast drying xontact cleaner.. then sa likod ng mixer nyo po sa output Left and Right channel may dial knob po doon for output volume.. try nyo po pihitin.. minsan kasi dahil sa katagalan nagloloose contact yon kaya humihina ang output ng mga channels..
@LeeFordDiYs5 ай бұрын
@@FixYahTv maraming salamat po sa reply sir. Parang yung DSP sir. Pati output meter nasa 2bars lang yung led naka unity yung input meter n led 0. Pati fader locate Hindi na accurate. May Facebook po kayo sir?