That part has nothing to do with the evap system.i can see a lean code being set tho.
@mariosalazar76643 күн бұрын
Thank you so much for your clip, well done and keep up the good work.
@hanitwfikКүн бұрын
I really appreciate your kind words. 🙏
@octaviousricks36193 күн бұрын
mine blows on floor and defrost and little on outter vents but the filter been changed as well
@hanitwfik3 күн бұрын
If you just replaced the filter without blowing air inside the filter box, you might have some tree leaves and dust blocking the system. Otherwise, you could have a door blend actuator problem
@octaviousricks36192 күн бұрын
@@hanitwfik but which door actuator the one on the driver side
@octaviousricks36193 күн бұрын
how did you fixed it.. i have a 18
@FranciscoGonzalez-ou4jv4 күн бұрын
Hi do you where os the coolant temperature sensor is ? Can you please help me out with this .
@hanitwfik4 күн бұрын
Here's a link with a photo repairpal.com/estimator/lexus/ct200h/engine-coolant-temperature-sensor-replacement-cost
@FranciscoGonzalez-ou4jv3 күн бұрын
@hanitwfik thank you so much Sr , i really appreciate it.
@Knightowl9165 күн бұрын
Customer said his car doesn’t start or crank after he shut it off when this happend to him what could bit be ?
@user-qo9qe2wx5r6 күн бұрын
감사합니다
@hanitwfikКүн бұрын
물론이죠
@Roger-il8iw7 күн бұрын
I’ve noticed this on all the 5-0’s. If it’s not the battery, it’s usually that you’re not letting it prime long enough or using cheap gas. The 5.0 need premium. It’s a performance motor.
@snap-off53837 күн бұрын
Nice workboots!🤭
@hanitwfik6 күн бұрын
They are!😂
@723lion9 күн бұрын
2024, vertical video on KZfaq.
@kingsosaaahah9 күн бұрын
Did it work after u installed that part
@dannysimoni10 күн бұрын
That connection is a bitch if you have big hands
@rafaelnavarro885710 күн бұрын
Changed my bank 2, still have bank 2 check engine light , what could it be ?
@hanitwfik10 күн бұрын
You even replaced the wrong one or wiring problem or a blowing fuse . What code do you have?
@rafaelnavarro885710 күн бұрын
@@hanitwfik P0330 Code P0330 indicates a fault in the Bank 2 Knock Sensor 2 electrical circuit for a predetermined period of time. That’s According to my check engine
@rafaelnavarro885710 күн бұрын
@@hanitwfik was told bank 2 was the passenger side , I have a 07 Tahoe 5.3 ltz , changed it, still have same code
@rafaelnavarro885710 күн бұрын
@@hanitwfik what fuse could I check ?
@hanitwfik9 күн бұрын
@rafaelnavarro8857 bank 2 is the passenger side . Let's do this if you have a scanner when you erase the then started the car dose the check engine light stay on or comes on right away or how long did it takes for the light to come on ?
@papitb390410 күн бұрын
Do i have to disconnect the started to do this?
@hanitwfik10 күн бұрын
Nope
@papitb390410 күн бұрын
@@hanitwfik ok thanks you
@hanitwfik9 күн бұрын
@@papitb3904 you more than welcome
@amado115611 күн бұрын
u didnt say shit ..no help at all waste of time
@hanitwfik10 күн бұрын
"I’m sorry you didn’t find the video helpful. I try to provide valuable content, and many viewers have found it useful based on their comments. If you need more specific assistance, it might be a good idea to consult a professional mechanic directly."
@joeaverage402912 күн бұрын
Th spark what is bad??
@joeaverage402912 күн бұрын
The what is bad?
@velizarmilutinovic294712 күн бұрын
ARE YOU DRUNK MECHANIC ? You sound drunk Also most transmissions DONT HAVE DIPSTICK
@stevemassari833916 күн бұрын
Hi. I have the same issue as you. Did ur old resistor work the motor at all before you changed for new?
@hanitwfik16 күн бұрын
Nope
@raghunathan431918 күн бұрын
Only thing good is the diagram.the rest is I dont know what?????
@buddy0h19 күн бұрын
I hear lots of people say they still drive with this problem, will this damage my engine?
@hanitwfik19 күн бұрын
of course it will keeps grinded your camshaft and the rocker arms then the dippers might blocking the oil screen .then you gonna have a misfiring problem it will damaged the catalyst convertor
@kevinsouthall210020 күн бұрын
Crap video , camera all over the place, why bother.
@robertpias791021 күн бұрын
Thank you man!!!
@hanitwfik20 күн бұрын
you are welcome 🙏
@KPCC22 күн бұрын
What about on a 22 Chevy equinox
@diljotsingh740923 күн бұрын
How much is the price for the oil cooler gasket job?
@hanitwfik23 күн бұрын
you know all shops and mechanics has different prices but to me if you have the same engine in this video i do it for $600 to 700 labor only
@Ahmedahmed-lu6vx24 күн бұрын
So u put the short wire in the upper one ?
@hanitwfik24 күн бұрын
correct
@Ahmedahmed-lu6vx23 күн бұрын
@@hanitwfik thank you so much
@Ahmedahmed-lu6vx23 күн бұрын
@@hanitwfik where can i get the diagram from?
@hanitwfik22 күн бұрын
@@Ahmedahmed-lu6vx alldata.com
@Ahmedahmed-lu6vx22 күн бұрын
@@hanitwfik i learned from ur video and fixed my car by myself, its been 3 months no one knows whats wrong with it! Thanx allot ❤️
@jenellahern113126 күн бұрын
This is not the location for the SE
@joeboe479428 күн бұрын
I have this same truck but need to do the back door window. There is not a single video on the internet for a 2006 f150 extended cab rear door glass replacement. Can anyone help me
@hanitwfik28 күн бұрын
FOR SUPERCAB, WINDOW GLASS - REAR DOOR Removal and Installation 1. Remove the rear door trim panel. 2. Remove the rear door mounted speaker. 3. Remove the rear door interior moulding. 4. Remove the rear door watershield. 5. Remove the C-pillar below belt bracket bolt and bracket. - Slide bracket down to disengage from U-channel in door. - To install, tighten to 10 Nm (89 lb-in). 6. Remove the B-pillar below belt bracket bolt and bracket. - To install, tighten to 10 Nm (89 lb-in). 7. NOTE: Some vehicles may use rivets instead of rear door window glass-to-regulator assembly bolts. Remove the rear door window glass-to-regulator assembly bolts. - To install, tighten to 11 Nm (8 lb-ft). 8. Remove the rear door window glass. - Pull the rear door window glass out through the top inboard side of the door. 9. To install, reverse the removal procedure.
@hanitwfik28 күн бұрын
FOR SUPERCREW, WINDOW GLASS - REAR DOOR, Removal and Installation 1. Remove the rear door trim panel. 2. Remove the rear door mounted speaker 3. Remove the rear door interior moulding. 4. Remove the rear door watershield. 5. Remove the C-pillar below belt bracket bolt and bracket. - To install, tighten to 10 Nm (89 lb-in). 6. NOTE: Some vehicles may use rivets instead of rear door window glass-to-regulator assembly bolts. Remove the rear door window glass-to-regulator assembly bolts. - To install, tighten to 11 Nm (8 lb-ft). 7. Remove the rear door window glass. - Pull the rear door window glass out through the top inboard side of the door. 8. To install, reverse the removal procedure.
@t3yrАй бұрын
I did not understand what the leak was about. I have a Great Wall car and it has the same diagnostic code
@____HEISENBERG____Ай бұрын
is this the same as my 2011 nissan altima 2.5s ? My clutch won't engage.
@ramirogovea3092Ай бұрын
I appreciate you recording this and showing us. You didn’t show us the actual expansion valve and how to remove it. Thanks
@ronaldwade6716Ай бұрын
I’m trying to remove bank 2 sensor on engine How?
@youeweuАй бұрын
Thanks for showing you have to remove the alternator first for the 2013 V6! Did the manual say how long it estimates mechanic time? Guessing 2 hours because I would take 4?
@hanitwfikАй бұрын
If you work straight, it will take about an hour and a half
@junkevidenceАй бұрын
Thanks! Would love to see a how to video next!
@BetterToDIYАй бұрын
This is exactly what was wrong with mine. One wire was broken. Thanks for explaining how to test the sensor too!!!
@hanitwfikАй бұрын
You can test it with 12v. You should hear a click. Also, you can blow air by your mouth in the sensor tube it should be blocked, keep blowing, and then give it 12v. The sensor should open and let the ait go through. Good luck
@NicedeskАй бұрын
kzfaq.info/get/bejne/oNucmZmjqdWwe5c.html Here is a sample sound of a J35 with a bad front cam.
@DIYAUTOCARАй бұрын
Did you replace the AC o-rings when doing this also?
@hanitwfikАй бұрын
No, I didn't because I checked them they were good
@adrianxaxoАй бұрын
How many camshaft sensor each side?
@hanitwfikАй бұрын
2
@DIYAUTOCARАй бұрын
Did this fix the issue long-term? What brand of alternator did you go with?
@hanitwfikАй бұрын
Yes . And Denso is the best brand
@NewzviewАй бұрын
I am having the same issues on my 2018 Range Rover hse
@hanitwfikАй бұрын
I have seen it many times
@wechargАй бұрын
lol you sound exhausted give yourself some credit I don't think this was easy!
@phillipcornett844Ай бұрын
Id give 1/4 a like, for a 1/4 video
@jamesbowerman5477Ай бұрын
Worked for my 2016 Dart Rallye. Same problems but this worked. Thank you.
@jasontribendis5864Ай бұрын
Thanks for the video, it helped me swap out my daughters blend door actuator. Some of the video was hard to watch but you were informative and the key parts were clear to see
@KRS115Ай бұрын
This video is very useful and encouraging to do it myself and saving a lot of money. Thank you for the valuable content. Btw, where is your garage located?
@tylergarrett4668Ай бұрын
Did you need to reset the TCM (Transmission Control Module) after installing this? After changing my “shift solenoid”, I turned my car on and had absolutely no movement when I put my ‘09 Maxima into drive. It can’t shift at all now.
@yaroslavyaroshchuk6868Ай бұрын
Thank you very much for your video it’s happened same Acura MDX with my daughter Car. 😊
@hanitwfikАй бұрын
I'm glad to hear that. Thank you, and good luck 👍
@roberttrevino4581Ай бұрын
Could it also be a bad IPDM, if it’s not providing power to compressor?
@hanitwfikАй бұрын
Yes, because the relay is internal
@paulafanous8111Ай бұрын
After the rev the tec said It need to change the computer by new one can you tell me why thAnk you
@hanitwfikАй бұрын
whats your car make model . whats the problem . do you have any codes ?