Is there no way to connect TX/RX for CANBus transceiver? I ordered a few of these because esp32 has plenty of IO, only to find barely any of it is exposed to use. Just the I2C and no SPI or TX/RX?

Thanks for the detailed video, Do we have Tutorial for integrating Arduino with 42D CAN module. I have a project with this requirement would really really appreciate your reply on this.

Hii really appreciate your detailed video, May you please share one with Arduino and CAN for 42D series of Motor drivers.

when i choose the board type its starting download something and the ENDSTOP field doesnt appear . how to solve this problem ? my board is mks robin nano v3.1

Clave WiFi Marlin esp es 12345678

Since when is a 72V battery a 6S? When i connect the 72V battery after installing no limits firmware the 75200 doesnt work at all. My BMS shows a short circuit. Controller not working. No connection via USB possible. 52V works.

Hello, how to add speed control to this?? i would like to use a momentary switch to trigger the start of a motor where the speed is set with the help of a potentiometer (as long as i hold the button, the motor rotates at the set speed, releasing the button stops the motor). I have connected the potentiometer to ADC1, GND, 3.3V, but where to connect the momentary switch? Thanks in advance for your help

Hate these robot voices

rip wifi?

How to flash it via WiFi? Is it possible to do this?

How to flash it via WiFi? Is it possible to do this?

for me impossible , still getting errors

can i use it with mks ups and pwc on mks robin nano v3 board ?

Is it support mks pwc 3 in klipper? Thanks

Hi MKS Team Could you offer any link for me that's giving some instruction to hook up external drivers on Cartesian SKIPR board.

Is there a version that works also with the CAN interface? Not like the low level Cangaroo?

I've got 2 issues with TMC 2209 and MKS DLC32. Need to know what configuration needs to be applied to avoid step motors jump steps. Someone who can copy&paste best config for nema 17 step motors?

Hi, i'm trying to set my five TMC2209 (X,Y,Z1,E0 and Z2) to UART mode and i don't know in which pin i should connect the fith one (doesn't appear on this video). Can you tell me in which pin i have to connect the wire?

esse tutorial funciona na mks tinybee ?

Can we use mks pwc with this?

Three-axis board with only two-axis control. What a piece of junk.

does this work with co2 laser?

excelente aun sigue pasando esto hasta en la version mks l v2.1 y con esta solucion se puede corregir el tema. gracias

I'm trying to configure the vesc tool so that I can use a potentiometer on the adc2 input, so that it works as a pedal-assisted power regulator on my bike, I use an accelerator on adc1 and a common cadence sensor, but it is dangerous to use the assisted pedal if you are using a profile with a lot of power, my intention is not to need to use a smartphone to change the profiles but just a way to change the assistance...

I'd like to know how a NORMAL person who isn't a programmer is supposed to know how to navigate all this information. I just want to restore the factory settings that I screwed up when I tried to flash grblhal onto my MKS DLC32 V2.1 card for my homemade CNC table. Good lord this stuff is a nightmare. Why can't it just be a simple "click on this and upload it" type of situation? How can you expect a normal guy to understand all of this crapola - which is one link after another leading to more and more files and folders and 404 alerts for failed links. Why do you need three tools to do one job - and why do you need to see a million different files and folders when you just want to perform a basic task? Holy Crapoly.

Mine just fails on build, somethin about FPSTR being defined twice, although not sure how

My vesc tool does not detect the 75300 but show the 75100 When run detect motor, vesc automately disconnect. Can u help me

Is the display a necessary component to operate the board?

Does your z Axis move when you adjust the "probe Z Offset" ? I have TinyBee and i cant get the Z axis to move to set the offset. I tried everything in this video. No joy Is there something about the board that wont let that work? Or does any one have a Marlin config where it actually works ? need for 3D Touch, Creality CR-10. I like the board. it be nice to get that to work.

I'd love to see how to connect this to an esp32. I am happy to see the MKS ESP32 FOC. I will start there, then maybe I will learn to program this board.

What button you use? Is impossible to make it work

Is possible to turn off the esc with button right? What button?

The hp84200 died on my after two days using very low amps do buy this escs guys

Is there any example for the CAN version?

How to connect BLTouch to the motherboard

is it compatible with the bigtreetech skr mini e3 v3?

I bought a flsun q5 and the board had turned out to be complete junk ad 3 yrs ago now they never responded back to help or troubleshoot or replace. The board is taken out now and no longer works. The section for the ribbon insert no longer holds ribbon for screen.

the solution definetly isnt to set the maximum offset higher, but to level your bed.... if youre printing a part at like 150mm, youll have around 1.5mm skew in it in the Z, /=| where the | is the top layer and / is the bed....

Could you link to the text file you are using for this config? I've spent all day typing in commands from your videos - and I'm still not getting anything out of my ODrive Mini V1.0 board. The documentation just links to a page in Chinese, which google translate only partly translates into English. The Git Repository only has some of the files shown in videos. I could really do with some help getting this running! Perhaps you could work out how to use it with the ODrive Web Gui? That makes the setup easy.

es compatible la pantalla ts35?

What happen with the website? 502 bad gateway error

Your videos are about as useless as your cheap knockoff boards

Is it compatiable with Tinybee?

Hi, is it compatible with MKS Robin Nano V3 motherboard? I have TMC2209 driver and simple Nema17 motors, and I would like to switch to closed loop motors.

o sea q no se puede usar via wifi con tu pc personal. xq se desconecta del wifi...jaja

Can we use key?

I have just put this on my K40. Lightburn does not detect it at all yet LASERGRBL does and can operate it (roughly but it moves). Any ideas?

no sale a cuantos volts trabaja esa controladora

hola, queria saber que controladora tienen para poder usar dos motores de hoverboard como motores de posicion, trabajan a 36v

hola, queria saber si ese shield me sirve para unos motores de hoverboard a 32v