Wondering if you have any thoughts on the depth required for a water table? I built a small CNC machine that I plan to attach a plasma torch to. I've almost got it ready to test but I'm working out a few bugs. The machine itself is made from v-groove aluminum extrusions and running Nema 17 motors. I can easily carry the entire 1000mm x 500mm frame and gantry setup. So it's going to be quite portable. I want to build a water table in the garage so I can place the machine on top of it and do a cut whenever I need to make a part. I was thinking of using an old refrigerator door as a water table. I'm just wondering how thick of a door I need to use to prevent the torch from blasting through it. Checking out your other videos right now and subscribe. Thanks for the info.

Saurais tu si 10 ans après, le site est toujours équipé stp?

What size extrusion do you use... like is it 30mm 40mm 1.5 inch etc

Hallo! Super Video! Ich möchte das bei mir in Mach 4 implementieren, woher weiß die Steuerung auf welchem Pin dein Schalter im Floting Z ist?

Sir , plz tell me How to configure the floating head micro switch in the mach 3 to sense the initial height ??? Plz reply. ..

Very nice machine! is it all open loop position control? What is the THC controller, and what is your max rapid traverse speed?

quisiera construir un cabezal flotante en casa, puedes compartir los planos @Mitch?

Place scribe sir

What port do you connect the limit switch to?

What port do you connect the limit switch to?

Hi what plasma cutter are you using

Just use twisted wire wheel cup angle grinder attachment. Will perfectly remove slag in seconds.

you forgot to say you need to change the refhome to false for g31 probe

Hi mitch i am trying to set a floating head in my plasma but i use LazyCam for creating GCode. Do you know if it possible to configure the Z Offset in that program, or it is only possible in SheetCam. Good Job and Vielen danke

Hello, great video. Can you send me the whole script from the postprocessor. Find that very interesting and would like to try that with me. I would the gladly the email address of me then by PN communicate. Thank you and greetings from Germany

we've been working with a plasma cnc for almost a decade now and the best way we found so far is this type of disc ran at lower rpm let me know what you think www.scule-austria.ro/disc-stern-gbs18024-pentru-slefuire-3917293.html?gclid=CjwKCAiAnvj9BRA4EiwAuUMDf60wwMN0LvKC7sZNGnl4dFveiEs0VC_llkKV2vcqBFDeChrgez6cixoCJS0QAvD_BwE

Big Help Mitch, love the way you organized this to be totally accessible with the minimalist slide system above. this is my go to guide. thx

Which thc did you used

Hey Mitch not sure if your gonna get this message but this is Jordan Miller from when we were kids. Nice channel dude.

great video...scribes are essential for making metal brake reference lines

This post works only in mm, my machine Is in inch, i can use this post?

This post work only in mm? My machine works in inches.. when you edit this post Is in inches?

Hello friend, can you please share with us which software do you use to make the G-code ? Thanks

hi! nice build! Can I ask how much the 8020 costed you in total of your project?

how to use M31 instead of G31 for mach3 probing ? can you please let me know . there is a problem with run from here action when you use G31 this is my Email [email protected] Many thanks for the great video :)

How do you start the cut? My handheld Plasma cutter needs to touch the metal once to start the arc, how does this work on the machine?

Where did you source your board material and the pins they rest on? Nice build!

Hi friend!! Exellent work You can pastme tve postprocesador?

My question is you operate a 4x8 CNC Plasma in a one-car garage?

Where did you get those plastic fittings and small valves

Nice job....I like it!! 👍🏻🚐✌🏻

donde cocigo el post?

I like it! Are you using 80x20? Can you do a video of how you collapse the whole and part of the structure? Moreover can you describe the join point for frame and legs and slidies in detail?

Great idea! How did you attach the rails for the pull-outs? It would be great if you could show the whole setting up? Is there anything attached to the van itself?

How do I wire the switch

Nice job! Are you doing it yourself?

Really nice work on the Plasma Table . Do you still have a PDF of the electrical system available

Does the foot switch turn on the light and the vfd?

program i use is universal gcode sender

HI I USE ARDUINO FOR MY CNC PLASMA AND I WANT MAKE floating head can you help me

THINK YOU IS NICE VIDEO

how exaclty do you set that up on mach ?......are you using a macro or something? im thinking about using sheetcam for my cad but im a little confused as to how the probing and then setting its self to clearance height will work...can you offer some insight?

Hi, I need help !!!! How do you connect the swicht of the automatic 0 on the board and on the Mach 3? I have a floating head and I do not know how to connect the swicht and I can not use the machine. I think I'm going crazy! Thank you very much and I send you a big hug from Argentina.

hello!...i had a question....im building a plasma cutting cnc machine on my own and i want to make a floating z torch head in order to probe where my material is and set the ztorch to pierce height........im not sure if this action is created in the mach 4 i am using, a special script you have to type out with gcode and include in the gcode generated from the part in cam software or what?........i want to first understand what exactly is needed and how i all works together, also what type of cam software would you recommend for plasma cutting out parts? thank you so much

Hy,how many hp motor?

Hey, you dit d great work with your plasma table. But i got a little question to you: Which output do you use for the engraving pen? do you made different tools with different offsets in mach3? we are using mach3, an powermax45 und proma thc too 😉 thanks for your time greets andreas

A guy I know who made his own table cut the supports just a little long , they have to be bent slightly to fit in there , it kinda makes a wavy look , this way he supports last longer , when he does a lot of straight lines , it wont line up exactly with the supports

also.. lead-ins lead-out.. lead-in.. perp .02 lead-out none. that tit at the end of your cut will go away. overcut of .05+/-

Man.. your pause after pierce is really long! arent you getting dimples at the pierce point? Especially on thin sheet youll melt a lot of material and never get a good clean shape. I know a lot of times this doesnt matter but on lines with no lead-in and really small holes, youll see that a pause of more than 1 sec will blow a big hole.

Good day Mitch Greeley are good your videos you can do me the favor of passing me a file of code that generates in sheetcam my mail is [email protected] thank you very much