Is the antifreeze needed in a tropical climate? never gets close to freezing (0C/32F) here.

What's the smaller of the 2 wires you disconnected?

how to get the arms to go lower to the ground

Huge thanks sir

Thank youuu

Thank you for documenting your Gen 2 inverter research. I just dismantled a 2nd gen and have everything. Do you think it would be possible to run the inverter using the factory HV cpu with the imobilizer and key, or should I skip all of that and just go with an openinverter board?

Lol a couple hours... bruh

Made my day! I was trying to pull a trailer and it kept swaying. This helped in figuring how to tighten the turnbuckles to keep everything tight. Also not fun trying to keep the rear blade from swaying. Thank you!

Which company this load test? Did you have any link to buy?

Great video. Thanks!

0:24 Make sure you careful with that power supply. Its not a charger. Cool video, I've burned many power supplies before learning i need a charger in the middle. A nice rc charger will do

Disgusting

Is it turning in reverse ?

Wonder if you could work the big gear back and forward until free… since is like just debris…instead of replacing pump…looks like 4 screws to get gear cover off…

Thank you very interesting I learned something new!

Great video

That's great! The boat itself makes more sound than the motor. I had considered doing this to my boat motor when it got toasted (see my channel) but I think I got 'er pretty close to put back together. I love your videos. Keep it up!

Fascinating videos on the VOLTswagen. I've been brewing the idea of using a Q211 MGR for the front drive of a diesel 4x4. Not sure if i'll be able to wrap my head around it after watching your videos, none the less i'll keep trying to make a plan for it.

I could not get mine apart like you did. I think the one I put in is China junk. so I get to do it again.... But I think that I fixed the old one with the silicone spray. it has a lot of rubber inside it. thanks for your movie.

if you spray silicone inside the pipes it will turn easy again. the motor should also be sprayed with electoral cleaner to get the carbon out and it will work again...

By disconnecting those 2 harnesses, is that sufficient to remove power from the brake caliper piston or does the negative battery cable need to be removed also?

Should not touch bulb bare hand

I hear that if you empty the gas tank on metal tanks it rusts from the inside with these Hondas and the fuel lines will break and be brittle

Do you know what size the o ring is?

Would this method work for my ‘05 Outback?

You are venturing into Tim's territory there.

What about sealing the screw holes?

Very clever!

You are the best brother, thank you 👍👍👍

Have any good snow yet? Looks like another mild winter here

That was a good idea. THANKS!

Thanks Buddy 😊

Thank you!

Thank you, I’ve been tryin to figure out why my brush hog is crooked.

The red triangle and I can hear the fan just started today

Hi if I can hear my fan does this mean I need a new battery or it just needs to be cleaned

You have mine beat by $25, but mine is way more secure. kzfaq.info/get/bejne/oL99Y9uLnbrbkXU.html You have an update video? 13:15 BTW the whole reason you have to use a 15AMP fuse in YOUR system is because you are using different wire gauges, goin up and down in size. You need to be using a uniform gauge for this sort of stuff. For any wire that is for that actual motor you need to use wire that does not restrict the flow of current. it looks like you are going from 16 AWG to the motor, then feeding the relays (87 and 87a) with 18 Awg, then the fuse holder looks like a 20 AWg wires them back to the battery that is at least a 16 AWG.

Hola me puede ayudar mi carro ya le remplace la pieza pero sifue arrojando el codigo ademas note que no llega luz al conector de la bomba osea que no logra encenderla😢

You may find adjusting the scraper bar first then place the shoes accordingly is the easiest order … that is the reason the shoes have so much adjustment travel options.

😂 *Promo sm*

Hi! Excuse me, sir. I'm trying to connect the weather vane to the ESP32 unsuccessfully. Could you provide some guidance on the connection?

Thank you for the video! I have load test my 2012 camry battery cells with an old headlamp bulb known as h4; all calls were holding 7.45 volts range and I had meter on for 20 seconds for each cell. If cells are showing capacity where it should be then what should I check next to fix P0A80 fault code? Thanks

What lake is that?:

I've never seen an electronic boat motor before 😮

Beautiful!

How do i get my bottom link Lower, it is 2inched to high

will this work on 2012 and are there led equivalent bulbs?

POS cars

As someone who works for the Subaru assembly plant in Indiana, I will never purchase a Subaru

Thanks for sharing