Northville Lumber

Пікірлер

@TeHaCe420 15 күн бұрын

Hardie boards are a joke. Its like Kia pretending to be Mercedes. Fake stone, fake brick, fake wood. Yall look like clowns putting this stuff on your houses

@MattFerguson26 23 күн бұрын

4:10 I'm trying to figure out, how do you finish the last/top board?

@rudyardgomeas6042 Ай бұрын

where do you find joint flashing. I've looked at every store and not one sells it.

@christypage9311 Ай бұрын

what is the cost of this slider unit

@briandevany860 2 ай бұрын

Is that information card accessible?

@clarencejackson5284 2 ай бұрын

Thank you!

@anthonyrampolla3884 3 ай бұрын

what should you do with the top of the trim if no caulk?

@lv2691 4 ай бұрын

When I installed Hardi-Plank 20 years ago, they recommended a 1/8 inch gap between butt joints! Now I get to re-caulk every few years.

@joeswheat 3 ай бұрын

The product went through some changes, I think. They did have some issues a couple years back, I think.

@kevinstearns2071 4 ай бұрын

You really need to make inside and outside corners I think the corners are the worst looking sticks out to me really bad been tiling for 30 + years and whenever I do the stacking stone I miter the corners because I just hate that stagger look

@jaysinner313studios 5 ай бұрын

i installed james hardie on 1 of the oldest houses in plymouth mi james hardie threw the homeowners a block party the house was like 128 years old we found old plymouth lumber underneath that the owner framed and put in his house cool deal

@charlesmauney3998 5 ай бұрын

all products expand and contract with temperature, there should be a thermal expanction number. For Hardie Boards: Coeficient of Thermal Expansion (COTE) per ASTM E228 is: Longitudinal COTE = 6.7X10E-6 in/in ° F Transverse COTE = 7.65X10E-6 in/in ° F. So for a 10' board it would be 0.0000067in/inF * 10'(12"/1') * 100F = 0.0684". So a 10' board with a change of 100F will change 68 mills (34 mills at each end). Not sure how much the nails will attenuate this change.

@dumbdems 5 ай бұрын

Idk how some of these pros try to say that bs. Everything moves just how much.

@diverdave4056 6 ай бұрын

my oh my I repainted my friends house that had Hardie prepainted siding all 4 sides of his house were different colors due to the amount of sun shine they got over a 12 years period ...it went from dark forest green on the north side of the house to a pale yellow color on the south side of the house...and who ever installed it - left plenty of wide gaps between the boards ... So are you SURE they don't expand and contract ? He nearly cried when he saw how nice it looked with new paint on it

@dumbdems 5 ай бұрын

They 100% move!

@diverdave4056 5 ай бұрын

@@dumbdems some of the gaps were a 1/2 inch wide !

@dumbdems 5 ай бұрын

@@diverdave4056 dang, didn't know they moved that much tho!

@diverdave4056 5 ай бұрын

@@dumbdems maybe it wasn't installed correctly ?

@dumbdems 5 ай бұрын

@@diverdave4056 seems like it, hard to be sure without looking but I'm sure they didn't look for studs and just nailed to the osb which isn't right.

@devonbradley3395 6 ай бұрын

Caulk dam huh

@ctc6960 7 ай бұрын

Hi, How did you install the cocktail rail?? Is there a special tool or screw to do?? Thank you in advance.

@rickeyjohnson1392 7 ай бұрын

$5500

@mikec0502 7 ай бұрын

What about post installed from above, still code approved for hurricane clip replacement?

@toyarj37 8 ай бұрын

How often does this stuff need to be recalled? Nobody talks about that. Is t composite better?

@lindalester9151 8 ай бұрын

James Hardie recommends using some very expensive caulk called Quad Max. It's a caulk that you can not tool. It also comes in the colors of the siding you pick. It's great quality, just very difficult to install without making it look like a 5 year old did it.

@oliverdiaz4029 8 ай бұрын

I work at that company in Saint Louis Missouri

@raymondngo9436 8 ай бұрын

Are you going to be able to ramp around top half moon window??? thanks

@kencole6154 9 ай бұрын

Our subcontractor failed to nail the James Hardy sliding into the studs. They randomly nailed it into the OBS, most nails missing the studs. A suggestion was made that the nails could be bent over on the inside of the wall. Is this practice acceptable or would it impact the warranty?

@TzNuts 2 ай бұрын

You are screwed when it expands.

@terramoo6936 9 ай бұрын

Not a fan, installed on a few houses, its not forgiving, our boss said he's not doing another job with it. At least the 4x8 sheets with battons. It scratches easily, repairs are difficult to make look nice. Off cuts are landfill bound. Take longer to install. At least for us.

@charlesgornowich7874 9 ай бұрын

I had a new house built and they said Hardie siding was the best. Now it whistles in the breeze and rattles in the wind. Should have paid the money for brick. What a nightmare....

@BuckHein-kl8gy Жыл бұрын

It shrinks its whole life.. Every job always shrinks up. Dont believe me go look at 5 to 10 year old jobs. Its garbage

@usa5439 11 ай бұрын

So what's the best siding then

@EdurtreG Жыл бұрын

Also to be used for a loftfloor?

@jamesfoley2658 Жыл бұрын

I’m glad I’ve been doing everything right but it’s good to know the clearance numbers so you sound more professional when a homeowner asks

@21gonza21 Жыл бұрын

Don’t you have to face nail the window trim and edges?

@richmickiewicz8234 Жыл бұрын

I need help with the OPPOSITE. I have a screened in porch and need to renail the screen so I am trying to remove the trim boards. How do I do it? I can send you a pic but the board (hardie plank) has hardieplank siding up against it. I GUESS there is caulking between the board and the hardieplank so should I use a razor and then try to pop the board off going north to south using a claw bar ??

@nofyfb123 Жыл бұрын

I checked your site and did not find the info you are showing - no instructions, no flyer, not directions. What am I missing? I mean other than those listed crucial pieces of information.

@decks4less Жыл бұрын

Try www.jameshardie.com/

@krobusek Жыл бұрын

He said James Hardi products don’t expand and contract?!?? WTF?!? 2:44-3:03 How are they exempt from the laws of science?

@2tmbrown Жыл бұрын

Price?

@johnleblanc6310 Жыл бұрын

Could of actually showed paint application instead of that.

@derrecktarr2099 Жыл бұрын

Should you install hardie when it's 20 or lower outside. It's been 12 degrees lately and gets up to 25.

@dumbdems 5 ай бұрын

What's your summers get up to? He's 100% wrong about thermal expansion on Hardie

@sw6065 Жыл бұрын

Ordered 9 pieces of sample Hardie Board invited 4 different contractors who attempted to sell me various vinyl products, as soon as I asked if they were trained skilled to install Hardie Board with homeowner references not 1 gave me a straight answer but I heard 3 of them say if water saturates the underboard unfinished side over time the Board will fail breakdown and mold. These were licensed NJ MIDDLESEX COUNTY companies only 1cstated that he had installed it. So citizens I took 3 of my samples placed them in a 5 gallon bucket filled it halfway with water left the bucket outside with the boards inside for 2 weeks exposed to rain . I took them out after 2 weeks straight submerged in water. NO CHANGE IN THE BOARD. April 2023 Hardie Board is going up on me home.

@brassmule Жыл бұрын

I used it for an addition on my home in 2008, and as an accent wall on the front as part of that remodel I did. It's 2023 now and it still looks brand new. I clean/low-pressure wash it once a year, and I've repainted (new paint color as the reason) once in that time frame. The stuff is great. Just be sure to use a rain screen behind it! Don't just slap it over top your house wrap. Use a rain screen! I also nailed mine every 8 inches hoping for a bit more wind uplift resistance since in my area we do get some regular high wind gust conditions.

@AnnmarieHillDVM 11 күн бұрын

@brassmule what's a Rain screen?

@rollinmckim4719 Жыл бұрын

Very informative and great graphics, Thanks!

@colossalmayo1642 Жыл бұрын

where can i get a print out for that sheet

@maddierosemusic Жыл бұрын

I'm sure you can contact your local lumber yard (not Home Depot) and ask them for one.

@Zomfoo Жыл бұрын

It’s a remarkable failure of design that the blinds when retracted are not fully hidden by the top rail.

@DonnieKluck Жыл бұрын

Are you able to install Versetta stone without using screws in certain sections? Only wondering since I was looking to redo the surround of my fireplace and was going to stone over the insert metal. So was wondering if there is a way to do this with Versetta stone.

@Hedgehodge- Жыл бұрын

if you rabbit a cut on cornerboards do you still need to caulk if the cut ends are sitting inside the rabbit? If so there is no point in me doing rabbits on the corners. Thanks for all the info

@sstupidsstuff3453 Жыл бұрын

No. Rabbeted trim eliminates the need for caulk.

@Hedgehodge- Жыл бұрын

@@sstupidsstuff3453 nice! Does it make it difficult to do if say rabbit a window and corner? You have to slide the siding down above the window to get it in there right? Which in the future if ever removed a piece between there you'd have to cut it out and caulk that one or remove everything to top of window , is that right? Or just rabbit corner and not window so it comes out easy of needed?

@sstupidsstuff3453 Жыл бұрын

@@Hedgehodge- it depends on the length of your Hardie board. For example, a longer piece like a 10-ft would have enough flex you could probably get it into the rabbets where you may not be able to do that with a smaller cut. I don't have rabbets on my window trim, only corners. The windows are caulked but not the corners.

@Hedgehodge- Жыл бұрын

@@sstupidsstuff3453 thank you, I was thinking of doing this since windows are done but not corners. Coravent into rabbit area and trimmed down to prevent bugs and then rabbit corners .

@BrightthgirB Жыл бұрын

Do you caulk under the siding

@maddierosemusic Жыл бұрын

NO!!! Not on this not on wood either.

@harryl7946 2 жыл бұрын

Having a new house built now. The Hardie board on the rear of the house has ‘bows’ above ⬆️ the windows. About 5 or 7 courses. 🤔 Is this an issue? Inspector said they might lay down after it ‘dries’ or ages. We have 11 months after close before I get anal. No other areas of the house have ‘bows’ in the planks. Builder is reaching out to the installers about this issue.

@robdawg1017 Жыл бұрын

Hardie plank should not bow and there is no drying or curing time. What likely has happened is that the pieces were not trimmed to the correct length and wedged into place resulting in a bow. Hire another inspector that knows what he’s talking about for the 11th month warranty inspection. The builder should fix this.

@lucastone2 Жыл бұрын

That’s funny! My last window guy said the sun would fix the windows he installed bowed, I never knew the sun could fix bad window installation. Sounds like your guy is doing the same. Most likely bad framing or plywood sheeting pushing out on that one part of the wall. The hardie will conform to the shape of what behind it, and no it won’t fix itself over time.

@dumbdems 5 ай бұрын

That Hardie is just following the wall. Good luck!

@benzun9600 2 жыл бұрын

gauge size of flashing? thanks

@kevincearley3304 2 жыл бұрын

Where can we get that installation guide ?

@decks4less 2 жыл бұрын

Try the Hardie Siding website.

@apriljohnson421 2 жыл бұрын

I was hoping this video would show what blade to use to cut it and what type of nails to use to install it...

@TzNuts 2 ай бұрын

It's a 4 tooth hardy blade. They are like 50 dollars

@TzNuts 2 ай бұрын

Make sure u wear a mask cutting this material. It creates fine concrete dust like a volcano and will affect your Breathing. I do siding and I don't recommend this garbage. It's heavy and only comes in 12 pieces instead of 16. It makes for twice as many buttjoints. ONCE AGAIN THIS MATERIAL IS GARBAGE. Go with 16 foot laminated press board pre painted. 👍

@susyandiza 2 жыл бұрын

I have a current hardi plank install. It is only primed hardi because the installer lied and said my county did not allow color and then when I discovered the lie they said it would be another 5000 for the colored planks (I was already charged 34550 for 1700 square feet of siding installation). So only one has come to do the job which I am ok with but I don't think the job is being done correctly. There are gaps between the siding and the trim and I can place all my fingers between the bottom window gap and the window. There is also large gaps between the gable trim and the siding and some of the top peak siding if literally flapping out at the edges. The top of the horizontal trim also has a 1/4 gap. They don't include caulking with the job so I am sure they will tell me to just have the house caulked when I finally call to complain tomorrow. Oh, one last thing. The but joints have large gaps between them so they caulked them without using the joint flashing. Am I being unreasonable saying the job is being done incorrectly or is this how the install should be.

@randomrazr Жыл бұрын

what did u do

@cengeb Жыл бұрын

1/4" is spec, butt joints are 1/8" and must have flashing at each but joint...look at Hardie insturctions on teh web site

@toyarj37 8 ай бұрын

34k for 1700 sq ft imma get vinyl. Lasted 31 years no issues