Can you put this straight on top of a concrete roof? I’m wanting it on top of my out building.
@delbut29 ай бұрын
what about non 90 degree corners?
@SouthernSheetingSuppliesLtd9 ай бұрын
Sadly, there is only the 90 degree corner option available. We could make a custom metal flashing to suit if required. Of which we would need dimensions and angle needed.
@stanos116810 ай бұрын
🤫👎
@assuredroofing7686 Жыл бұрын
Definitely not easy to fit. The clips are so tight they take your fingers off!
@evanoliver44 Жыл бұрын
Hello sir thank u for video ,,for how many years we can do the maintenances for this type of steel?
@SouthernSheetingSuppliesLtd Жыл бұрын
Hi Evan, maintenance can vary between material finish and location, i.e if your near the coast you will need more maintenance than in-land locations. Our leathergrain coating has great durability and requires less frequent maintenance.
@ZussieMakesit Жыл бұрын
Wow! really good video! thank you I'm working on an awning roof with corrugated metal and this is Gold info, I've been trying to piece together what it all entails and this really helps!!
@SouthernSheetingSuppliesLtd Жыл бұрын
Thank you ZussieMakesit, reallygood to hear our video helped you. Have a great day.
@BM-wt3po Жыл бұрын
It creates big noise when raining.
@yanniszachos2250 Жыл бұрын
Are clips not required to secure the planks on the battens? most of the installation videos i've seen they same to use clips but wondering if these are necessary after seeing how you do it? Thanks
@GazlarW Жыл бұрын
What is the fire rating of the cladding ?
@SouthernSheetingSuppliesLtd Жыл бұрын
Hi GW, our composite batten cladding is B rated, which means it is combustible due to it being a wood plastic composite. Hope that helps. Here is a link to some further information: www.southernsheeting.co.uk/batten-cladding-product-page.html
@GazlarW Жыл бұрын
@@SouthernSheetingSuppliesLtd Thankyou for getting back to me I’m looking for something which will satisfy the requirements for Building Control for fire safety due to my garden building being less than a metre from the boundary Your product looks great 👍🏼 but unfortunately for me I can’t use it
@SouthernSheetingSuppliesLtd Жыл бұрын
@@GazlarW Hi, have you thought about using another cladding material like fibre cement based which is fire-resistance rating A2-s1, d0 with 50-year life expectancy. We do two types and are both approved for building control, the aesthetics are different but might be worth looking at. www.southernsheeting.co.uk/weatherboard-product-page.html
@GazlarW Жыл бұрын
@@SouthernSheetingSuppliesLtd thanks I will take a look 👍🏼
@jannicks.1685 Жыл бұрын
Hello, Could you be so kind and tell me the name of the animation software that was used for this excellent video? Thanks in advance.
@SouthernSheetingSuppliesLtd Жыл бұрын
Hello Jannick, we had an agency create it for us, so unfortunately we dont know, sorry.
@vivekproja3629 Жыл бұрын
Very good
@zyord8159 Жыл бұрын
Hi, I'm planning on using these on a shed that has a chimney, do you think silicone roof flashing works well with this type of panels?
@SouthernSheetingSuppliesLtd Жыл бұрын
Hello, if you referring to a steel flew coming out of the roof the answer is yes, the dektite pipe flashings work well however it also depends on the size of the pipe and how far down the roof the pipe is exiting. It is quite common to use what we call a ski slope flashing in the industry, this comes down from the ridge and passes the pipe by say 300mm for example, it bridges the corrugations of the sheet and you would need to insulate under the flashing and use a profile foam filler to block of the end however it gives a much flatter surface for the dektite to be fixed too, no need to mould it around the profile and it also eliminates the pipe becoming a dam in the valley of the profile. There are other things to consider with any roof penetration as this increases the chance of a potential leak later, it may be worth considering doing a side exit and running the chimney out of the wall and up.
@giedrel.1756 Жыл бұрын
Why is there the hieroglyph of "х*й"?
@rollformingmachine1 Жыл бұрын
our manufacture various kinds of roll forming machine for producing the following products. Such as Roof Tile, Wall Panel, Roofing Corrugated Sheet, Floor Deck, C & Z Purlin, Highway Guardrail, Sandwich Panel, Container Board, Car Panel, Roll Shutter Door, Downspout, Decorated gusset, Steel Pipe...etc.
@mdakterhawlader2123 Жыл бұрын
এই টিন আমি আমার ঘরে লাগাতে চাই
@harshayaliwal2971 Жыл бұрын
How did you make this sir
@harshayaliwal2971 Жыл бұрын
Which app or Web site
@billytobin76952 жыл бұрын
Excellent insight, than you
@clairezhao60432 жыл бұрын
good video
@sharadsharmaa2 жыл бұрын
Thanks very much for the info. Great animation, to the point!
@SouthernSheetingSuppliesLtd2 жыл бұрын
Thanks Sharad! Glad we could help :)
@metalsupplier8542 жыл бұрын
we export roofing sheet to al;l the world, if you need, contact me
@philotis18962 жыл бұрын
why cant the fixings go through the raised corrugations parts Water doesnt tend to flow there ?
@maryellis36612 жыл бұрын
Should the screws not be on the high points?
@SouthernSheetingSuppliesLtd2 жыл бұрын
Hi Mary, If you screwed on the top of the profile (high points) it would compress the profile, possibly bending it. You'd also need a much longer screws to reach the wood/metal. Hope this helps.
@maryellis36612 жыл бұрын
@@SouthernSheetingSuppliesLtd I was told on the hight points as water runs down the low points and can get in where a on the high points water cant run down ?
@SouthernSheetingSuppliesLtd2 жыл бұрын
@@maryellis3661 Hi Mary, No its a common misconception that you have to fix on the crown. It is absolutely correct to screw your main fixings in the valley as the neoprene washer on the fixing needs a hard flat surface to bed in correctly. Hope that helps :)
@anthonyday62842 жыл бұрын
This has be a big help Thank you
@SouthernSheetingSuppliesLtd2 жыл бұрын
Glad we could help
@shreyashnaik99762 жыл бұрын
Can we apply this over asbesto sheets?
@kerkezz2 жыл бұрын
What about residential buildings? Why only industrial and commercial applications?
@nickreid52972 жыл бұрын
Never, ever, put the screws in the valleys when laying down a roof. They belong on the hill tops--for reasons which are too obvious to spell out.
@duncankingston502 жыл бұрын
Nick - This is worng advice. Special saddle washers should be used if fixing through the crown of the sheet to avoid denting. Please refer to a number of manufacturers installation guides on box profile. You are however correct if fitting corrugated profiled steel sheets.
@nickreid52972 жыл бұрын
@@duncankingston50 OK, I'll qualify my advice. In practical terms, there is never a case for putting the screws in the valleys, even for box profile roofing. Don't allow anyone to do this to your roof unless you can be sure they will be around in twenty years time to fix the damage caused when the washers fail. And some of the the washers will fail because roofers always over or under tighten some roofing screws. My objection is that the video shows this as 'the' way to fix roofing sheets, and does not warn users of the potential pitfalls. It's simply a risk roofers don't have to take.
@007alztruli2 ай бұрын
@@nickreid5297 You haven't warned users of anything either. Too obvious to spell out? What sort of comment is that? If you have something to say, say it, or keep it to yourself
@nickreid52972 ай бұрын
@@007alztruli OK, I'll spell it out for you. If you put screws in the valleys, water will eventually leak through, rotting out the roof structure. This will happen if the roofer over or under tightens the screw, or years down the track when the washers deteriorate.
@ainhat.Ай бұрын
@@nickreid5297i think the tricky bit is that with this box type cladding you have a flat top not rounded like with corrugated sheets that means you can not tighten the screws enough as the flat will pull down, an arch has more structure. Therefore you will bend it and the washer wont sit right and wont be pinched right. My 2 cents anyway. I am installing my roof in the next few days.
@adam_lux46912 жыл бұрын
Great vid
@maryellis36612 жыл бұрын
How do you stop water going back under the roof at the gutter?
@12vLife2 жыл бұрын
Why not residential? I am wondering if these 6" Nucor panels (or similar or thicker) can be used for new residential construction in Florida, USA for something like this: kzfaq.info/get/bejne/mbx0fM1iqdSuqGQ.html
@Papastomper2 жыл бұрын
Why to screw in the valley vs the arch? TIA
@osmanosman92262 жыл бұрын
Excellent.Helps tremendously for beginners.Effective,clear explaination with animation.No distraction with human voice.Great idea in tutorial .Iike the way it is presented in stages with tools needed to facilitate smooth work flow.👍👍👍👍
@XX-kf7mx2 жыл бұрын
@ 1:00 how come as the metal sheet increases in thickness their span distance increase, they should actually decrease as more weight would need more supports? Can you please explain this
@ParaBellum20242 жыл бұрын
The thicker material is more rigid, and can therefore span a greater distance.
@sullivanphilip2 жыл бұрын
Extremely helpful and well thought out video that provides all of the key information to do the job right
@SouthernSheetingSuppliesLtd2 жыл бұрын
Thanks Philip.
@pritam46352 жыл бұрын
Ji mera head room 160 sqaure feet ka hai. Length - 16 feet width-10feet To 10 feet. 3.5 ka colour sheet kitna lagega?
@VWApachey2 жыл бұрын
What are the costs of those sheets ?
@SouthernSheetingSuppliesLtd2 жыл бұрын
Hi Mark, if you visit our website you can see prices which are based on quantity. www.southernsheeting.co.uk/box-profile/c-263.html. Please do not hesitate to contact the team should you require any further help.
@vinodnarayanan72862 жыл бұрын
What is the price of the sheet
@foodlettuce072 жыл бұрын
service available in Delhi?
@m.natarajanm.natarajan97382 жыл бұрын
Manufacturing place with contact number & price
@Lookitout3 жыл бұрын
Wowo amazing
@naveendalal53173 жыл бұрын
Bhai prontol panel ka bnwana h koi no
@AnkushKumar-py2ef2 жыл бұрын
7248711431
@aravkumar5783 жыл бұрын
भारत में कहां से मिल सकता है
@kevinaldcroft62913 жыл бұрын
The only problem I see here is placing screws in the valley of the profile. I had a pergola attached to my house and the builders placed screws into the valley of the profile and most of them leaked. I did not realize what was happening until the timber fascia board of the house began to rot, by that time the damage was done.
@duncankingston502 жыл бұрын
If using the correct fixings with EPDM washers, tighteneted correctly, this should not be an issue. I would check the type of screw used.
@EelingStudios Жыл бұрын
I have to agree and have done many small roofs with these sheets and always fix through the ridges. My thinking like yours: If any fixing might leak then at least it's at the highest point whereas if fixed through the 'valley' Sod's law says it will be at the lower end of the sheet at the point where. most of the water will be, i.e. in the middle of a river. Likewise I've never seen the sense of fixing roofing felt with nails. If you search on youtube you'll find more than one channel on these sheets recommending fixing on the high points.
@glevesque52953 жыл бұрын
What do you do if the day you installed your roof the wind was coming from the west, and the day after it comes from the east ? Do you have to uninstall and reinstall your roof each time the wind changes direction ? lol
@edmtb16032 жыл бұрын
Yes. Yes you do.
@dmgladden3 жыл бұрын
Ive just done my conservatory roof using the 100mm (4") insulated steel sheets and really it was so easy and its so strong i have a span of 2.7m (9') with only end support and i can walk on it
@SouthernSheetingSuppliesLtd3 жыл бұрын
That is great to hear David and hope our video helped you. Have a good day :)
@MrAdrianten3 жыл бұрын
Any installers of this product in East Kent/ Thanet area please?
@SouthernSheetingSuppliesLtd3 жыл бұрын
Hi Adrian, many thanks for your comment and we can certainly help you with your question. If you would like to call us on 01342 315300 and we will be more than happy to help you. Have a good day.
@ranau51893 жыл бұрын
hahaha..screw wrong please.
@duncankingston502 жыл бұрын
You should fix the main fixings to the low part of the profile - the video is correct. This method avoids denting the crown and ensures a firmer fixing point as the screw engaes straight into the joist.