Great video, I hope you have enough room for your top shot.
@Betterthanbought.Ай бұрын
Yaa couple ppl wondered that. These are our high speed setups specifically for trolling for wahoo. I packed it on there but new it wasn't as tight as it could be. Once we got to the keys i let out about 3/4 of it hooked to a num4 planer doing 8 knotts & cranked it all back in only used a half gal of sweat😅 & then i had plenty of room for my 50' wind on. Was a gamble i knew it was stuffed but i wanted every inch i could get & it worked out. Good eye man you have a clue unlike alot of the commenters that just dont understand or even care to ask what the setups used for. lol. A guy using a shock cord & cigar weight wouldn't use a topshot or wind-on or even wind on the shock cord so he could stuff it real good. But ppl dont ask or understand most times. Tight lines to ya my friend & be safe out there🙏🙏 appreciate you stopping by the channel👊
@andykjohnsonjohnson7622Ай бұрын
It's called a R-clip , Because it looks like the Letter "R" , good information video tho 👌.
@flattenthecurve8623Ай бұрын
Shouldn’t you be using American Made line on your American Made reel?
@Betterthanbought.Ай бұрын
Absolutely & with your wallet i would. We're not all rich & unfortunately for me i have to wait for the sales. This was a killer deal so on it went. Its quality line regardless. Does matter to me i buy alot of usa products but i cant always do it man🤷♂️. Sorry to disappoint ya👊
@USMC130FEАй бұрын
I sure miss your videos.
@USMC130FE2 ай бұрын
I really wish I could contact you as I have a bunch of questions about a lot of your videos!!! Love the content!!
@osamachakik73652 ай бұрын
I like your video nice and informative i just think you should change the rod running braid i wouldnt use that rod the wheels dont work well with braid maybe change it to a strong rod with just the holes instead of the one with the wheels would be alot better for trolling and turning youre lures will straighten up quicker
@Betterthanbought.2 ай бұрын
Ya i agree most full roller setups dont work well with braid especially with the xtra wide reels. That said these rods have a different wheel setup than most so the line cant get stuck beside the wheels like most setups do. Its made/designed specifically for braided line & i have never had a single issue with any of them. We actually have a few of these setups & fish them hard. I have had them for several yrs now & couldn't be happier with them. There specifically setup for high speed trolling for wahoo mainly with plainers & not used for anything else. Mono is too thick for this application it causes too much drag aka line scope stopping baits/lures from diving deep at h8gher speeds. The thin braid is a must have. But to each their own my friend. I appreciate you checking out the channel. Tight lines & stay safe out there👊🙏
@davidgrochmal60232 ай бұрын
I just put a150 lb braid on my penn 309 for fishing of the holyoke bridge for stripers and shad plus sometimes you hook onto a monster sturgeon I wish I would have known what I just learned so far my biggest striper is 50 lbs 10oz unbelievable fight when your a 100 feet off the water I lost a 12 to 15 foot. Sturgeon I played for 3 hrs then broke me off I was heartbroken. That's why I went to 150 lb test I was using 80 no more that my fish story but true !!!!!!!!!! Thank for the information!!!!!!
@anakngdagatfishingtv3 ай бұрын
sir what material are your molder are made?thank you
@93Tillinfini3 ай бұрын
R is the same thing. You can also buy the “grease buddy” for the Mag and PTO side. It goes on the tube you showed on the PTO side and a bolt with a hole in the mag side. Then you can grease them with ease.
@THLedgar3 ай бұрын
Look up teamhardlife his anaconda knot he made with hollow core braid doesn’t not slip
@Betterthanbought.3 ай бұрын
I follow him already but haven't seen that knot. I will most definitely check it out. Appreciate the suggestion👊🙏.
@nealskelton14253 ай бұрын
Great job. I'd like to thank you for taking the time to make this video.
@MIHfishing5 ай бұрын
Where is your reel seat? You got to have that .
@Betterthanbought.5 ай бұрын
Its in the reel box. We live in maine & we fly all this equipment to the keys in the belly of a jet each fall. Once down south everything gets setup properly. Thanks for stopping by👊 tight lines
@MIHfishing5 ай бұрын
Hell yea bro thanks same to you.
@arsenuts4115 ай бұрын
As others have posted great video it would be helpful to get the pipe lengths as I would love to make a few.
@stansvrlinga67505 ай бұрын
What species are you trying to catch with these 7/0 in-line double hook rigs?
@Betterthanbought.4 ай бұрын
There for pelagic trolling lures used for Wahoo Mahi Marlin, Sailfish ect. Personally i just use them for Wahoo but we always pick up mahi also. They help prevent short strikes/misses when high speed trolling. Good for squid skirted & mylar skirted lures. Cant run double hooks with anything flashabou skirted they'll tangled up bad you'll want a single hook far back for flashabou. Hope that helps. Apologies for the pathetically slow reply.
@kylehodges37295 ай бұрын
What rod is that?
@Saltwater_Odysessy5 ай бұрын
Sounds like you are from Maine or Canada.
@buster91dg5 ай бұрын
Does anybody know the correct amount for the PTO side? I just rebuilt the lower end but I had a hard time getting the inner pto bearing. So I have a little bit of Isoflex left over that I’d like to inject in.
@Betterthanbought.5 ай бұрын
10-15 ml is what it is said to be correct for a refill on the pto side. Ive done 10ml without any problems. Just dont overdue it or force it in otherwise you risk blowing out the seal. Good luck.
@Alex.rus.786 ай бұрын
А вертлюги какой мощности(lb/кг.) ?
@walawayneila67636 ай бұрын
I love this ❤
@billmyers85726 ай бұрын
Great video thank you
@Betterthanbought.7 ай бұрын
Anytime man. Just realized i responded from my other account my bad. Happy Holidays to you & yours my friend.
@mitchelsanborn23957 ай бұрын
Do you pull your seal off before you add the grease so that the pressure from pushing it in has a place to go? I’ve heard about the inner seal for the outer bearings could blow out. I’m about to grease my bearings on a rev 500, and was just curious if I had to worry. Basically I’m wondering if I’m able to just put the grease through that port you show, while turning over the motor slowly, with the seal on
@thegreatgreennorth99837 ай бұрын
No concerns unless you put too much in there. Dont force it go slow & slowly rotate as you said. Keep the isoflex inside/warm it will make things much easier. If your concerned put in half what they recommend go on a good ride then add 2nd half👍 Ppl that just force it in quickly or use too much can definitely push it past the seal & cause major issues. Follow the guidelines you'll be good to go. Now if your super fussy & have no problem yanking the clutch then sure drive a acrew into the seal pull it wipe out all old grease then do it from that end & replace the seal. But again dont overdue it or when you go to seat the new seal hydraulic pressure will blow the inner seal out as your saying. Sounds like you have a good idea about it all so i would suggest doing whichever way you feel most comfortable with👊 Thanks for stopping by the channel & happy trails my friend.
@mitchelsanborn23957 ай бұрын
@@thegreatgreennorth9983 thank you, I appreciate the input!
@marcbrazzers5 ай бұрын
@@thegreatgreennorth9983what about injecting half of grease slowly into the nipple side with the seal off (while turning motor slowly), and then the other half putting into the face of the outer bearing (once the old grease is all wiped away). At same time, it replaces the old seal that can potentially leak air and blow the motor. Also, I wonder why they didn’t add a nipple to the MAG side? Is it because there’s only one bearing on mag side?
@northofhwy81807 ай бұрын
Thx for making this video.
@mattsalvadore66397 ай бұрын
Would this same theory also work for 2003 600ho/800 motors?
@d.customs31755 ай бұрын
Yes
@christopherromina54458 ай бұрын
By doing that way the line won't come out right way one side will fill more, get a fishing machine to put line on, it will be faster
@thegreatgreennorth99838 ай бұрын
You can use what you'd like but this is how i spool all our reels always have always will i dint like a rushed job. Its tight the line dont dig in we high speed troll planers with these setups you couldn't possibly put anymore tension on them😅 if they where going to dig they would have & there wouldn't be a 65lb wahoo on my wall my friend. You do you, machine away my guy👍👍 ill keep stackin it on proper slow n steady👌
@livebaitfishing40308 ай бұрын
Such great videos wish you were still making videos!
@billmyers85728 ай бұрын
Super good info. Thanks a lot
@jamievalleau22429 ай бұрын
Fantastic video! Thanks for the detailed explanation
@fernandonogueira77719 ай бұрын
Thank you very much for that valuable teaching
@tylorbyington76029 ай бұрын
Doing this can blow the inner seals, cant it? The middle red ones
@thegreatgreennorth99839 ай бұрын
No isoflex doesn't reach the inner bearings ever those 2 are oil bathed. Please watch the video you will see how there all seperate. Pto and mag sides get isoflex only. The inners get bathed in 2 stroke oil constantly. Hence why those rarely fail. Using more isoflex than is recommended can damage the inner seal for outer bearings by creating hydraulic pressure just dont overdue it theres clear amounts specified for each yr/model simply follow that & your good to go👍 also make sure your buying real isoflex from a (dealer only) Hope that helps clear things up👊
@jayfavel44478 ай бұрын
@@thegreatgreennorth9983 Great explanation about the outer bearings. The 2 center bearings aren't in an oil bath, they are lubed from the oil injection. Only the water pump/oil pump gear/bearings are in an oil bath. Check out a shop manual and you'll see that they spec to add 50ml of oil to that cavity when assembling the engine. Also if you look closer at the crank in the video, you can see where the red center seals are located. They're on the wrong side of the bearing if they're meant to keep the bearing in an oil bath.
@thegreatgreennorth99838 ай бұрын
@@jayfavel4447 ya im well aware i could have/should have explained that better or worded that differently for sure. Good clarification👍
@johnchase39209 ай бұрын
Any pics of those after a few days trolling, some wahoo, tuna and makos? None of my used ones look that sweet!😁
@Betterthanbought.9 ай бұрын
Absolutely do go ck out my Instagram been in the keys for past 2 weeks been cleaning up. We only fish 2 wks a yr down south & those baits are brand new im not sure where you got used from. My Instagram is Thewoodworker1. 16 tuna 2 wahoo 9 mahi 3 cudas bonitas bunch of reef n trash fish. 1 week offshore. We do a family trip with our kids so don't exspect alot. The kids can only take so much before its not fun anymore & its their vacation too. More about memmories than anything. But go have a look just let me know your ig handle & ill approve you👊
@davidguel90599 ай бұрын
How many inches is a that pipe in the video and how many pounds does it come out to be? I know you mentioned 10 pounds for the large one but just wanted to make sure on the length of the pipe, thanks!!!!
@exasperatus200210 ай бұрын
How long of each pipe, makes what size weight?
@flygirlfishingerica480810 ай бұрын
Awesome video thank you so much
@paulsuarez820110 ай бұрын
Good job
@chrisanderson454411 ай бұрын
Great job explaining! I have an 800r and will be doing isoflex soon. Thx so much. You're a great teacher!!!
@Betterthanbought.11 ай бұрын
Make sure you get real isoflex from a dealer. There's tons of imitation crap labeled as iso but its not the same & will cause issues. Have a helper turn the engine over by hand (plug wires removed) as you do the mag side it will help get it spread through more evenly. Just 1 slow rotation as you squeeze in the isoflex. Thank you for stopping by the channel & happy riding this yr man👊 hopefully we get some major snow🙏🙏
@jordanlynch81859 ай бұрын
Thanks for the clear explanation. I'm also servicing an 800r I just don't see the access nipple on these blocks. Only have 4 ports on carb side of motor. 2 oil and 2 air pulse lines. Great trick with the ziptie and rotating motor to check for access to bearing.
@larryjohnson559711 ай бұрын
Yeah I’m interested in buying 4 rig and ready how much money
@lonnieberg66211 ай бұрын
I'm sorry folks this made my head hurt. It's a deep drop lead not a classic car
@thegreatgreennorth998311 ай бұрын
Some of us take pride in everything we do sorry if thats odd to you. You can use a cement block for all i care my friend🤷♂️ That should be easier on your head to figure out👍
@glynnmaddox454611 ай бұрын
Have you ever considered using thimballs on the split ring or barrel swivel crimps?
@r.bouth.645711 ай бұрын
Is your pipe tapered to get loose after cooling of or when it cools down it do get small in diameter enough to come out of the pipe..
@Betterthanbought.11 ай бұрын
Straight, undented ,clean ,thick wall aluminum pipe. Like you say the lead exspands when hot then contracts just enough to fall right out. Oil the inside up and quench it in water quickly like i show on the vid. That quenching makes your lead a lil harder also. If you have any questions just hollar. Make you some up👊🙌🙌
@r.bouth.645711 ай бұрын
@Betterthanbought. talk me some about the weight you use to fish in very deep water and what kind of fish do you fish at most deep waters...have video's ot it ?
@Betterthanbought.11 ай бұрын
Weight will vary depending on the current, water depth your fishing & even your line thickness. Say your fishing in 500-600 feet with 2 knotts current 5lbs should be about right. Now get out into the Gulfstream in 3-4 knotts of current and say your dropping 1500-2000' for swordfish your going to need 10-12 maybe even 15 lbs to hold bottom in that situation without it scoping out & being 1/4 mile away from the boat. You don't need to be exzactly vertical with your line but kerp it close to it without too much excess weight. Takes lil figuring out/testing at 1st. Use a good braided line for this type of fishing its very thin & cuts the water much better. Wont scope out nearly as much as mono does meaning you can use less weight. When you drop let it hit bottom then bring it up like 20' & drop it again then lift into the zone you prefer/want to fish from there species will dictate where you run your bait height wise. Now just repeat that every 10-15 mins as you drift to make sure your still in your zone/depth range as bottom contour will be constantly changing most times. Hopefully that's the info your after my friend👊 its a basic idea but should get ya going.
@Betterthanbought.11 ай бұрын
@r.bouth.6457. I dont have any vids but ck out capt nick stanzyk his KZfaq is stanzfam he is a pro swordfisherman gives great info lots of vids for ya to see how it all works.
@larryjohnson559711 ай бұрын
Can I just buy them made up from you?
@ethancalvary147811 ай бұрын
Could u use bondo for the molds
@Betterthanbought.11 ай бұрын
People deffinatly do but how well it works im not sure about that. Try a couple tests with it. Maybe warming it will make it more fluid too.
@luxorbill26911 ай бұрын
Putting that ring on is pure magic! I spent a lot of time fishing the hooks thru. Great how to video.
@naturalmystics-kd9vt11 ай бұрын
Thank you so much I have to like your videos you are a friend
@Betterthanbought.11 ай бұрын
Thank you my friend👊🙏
@luxorbill26911 ай бұрын
Wow, surprised how easy it fell out of pipe. I used thin walled and it didn't come out. That thick walled is the trick.
@Betterthanbought.11 ай бұрын
Ya exspands more problebly use a lil oil also the 3 in 1 seems to work well but im sure any oil would do. Also no dents dings & file/smooth off the cut ends you should be stylin my friend. Thanks for checking out the channel👊🙏
@luxorbill26911 ай бұрын
Made 2 leads today based on your video. Could not pretty up the top like yours. Making sure very vertical is important like you putting a level on it. I eye balled it and just off plumb. Must be vertical and plumb. I use Stainless bike spokes for eye.
@stevequate1797 Жыл бұрын
What a damn good video short sweet to the point love it kkk lol o M 16:17
@a.p.i.7196 Жыл бұрын
Great video! What number spring rings are those? Also - what’s the advice on a smaller Yo-Zuri Bonita 6”?
@Betterthanbought. Жыл бұрын
Hey thanks for stopping by the channel. I use Owner hyper wire rings & swear by them💯 #11 on the 8" large bonitas and #8 on the smaller 6" ones. Those seem to match up pretty good. Try n keep your loop small also so it has less drag & wont effect the lure negatively. Those Bonitas can be finicky keeping everything tight helps alot. Happy fishing my friend👊 stay safe out there.
@genemiller5699 Жыл бұрын
Thanks for the video! Helped me out a lot. Just bought an 04 f7 and it didn't have a helmet plug on it. Wanted to hook one up but didn't want to splice into the headlight wires like a lot of other videos were saying to do. Found that auxiliary plug on my machine it's behind the speedo. Went to autozone and bought that extension adapter that you showed and spliced into that for a plug. Quick easy instal without having to cut into wires on the sled. Thanks again. Also should add I'm a fellow mainer lol
@Betterthanbought. Жыл бұрын
Happy to hear that man👊 Alot of ppl dont realize that aux cords in there waiting. By far the best way to go imo cheap & effective no splices to give you issues down the rd👍👍. Appreciate you checking out the channel & commenting man👊🙏
@charlieallen180 Жыл бұрын
Just use two crimp’s instead ither side
@Betterthanbought. Жыл бұрын
I have seen it done but im not reeling metal crimps through my guides no thank you. 1 chip & its over you'll break off everytime. Dont like wind on swivels either same problem guide destroyers. The loop is king imo its simple & easy to do👍.
@fishpraslin Жыл бұрын
Hi, really enjoy your videos, how do you attach the lure head to the mold floor? Thanks