Линейку между деталью и сверлом, прижал чуток

Станочный парк есть, а ума нет🤷‍♂️

Jajajaja y cunado saca el centrador del taladro debe quitar el cilindro a perforar y estamos en la misma... Jajajja

Il problema è se il diametro è inferiore

Get a lazer Pointer, put it level now you got a dot wow that would work

Какая чушь!

Це щоб срать не хотілось

This is how a simple thing can be made complicated

Und wie bekomme ich den Bohrer rein

Какой же бред

Schon jemand aufgefallen wie schräg das Holzstück oben im bohrfutter hängt 😂.?

Чуть мозг не сломался от увиденого.

so if you can't find center, build yourself a jig first, and of course that jig requires you to find center multiple times, so you'll need a jig to make that jig. Also after you find center, you get to then reposition everythjing because you've chucked up the jig and you'll have to remove that for the drill bit. This is the dumbest video I've seen today.

250 полуляхов из 250

Криво. Не по центру.

The most idiotic video!!!!

It's far easier than that. Use a thin piece of metal like a feeler gauge between the bit and the workpiece. Move it beck and forth. Whrn it is horizontal you are over the centre.

Mantab

Congrats... Now, prove your work useless by moving the wood so you can reinstall the drill bit 🤦🏻‍♂️

.а можно было на сверлильном станке (в первой стадии) в металле насверлить отверстий разного диаметра - вот и универсальный кондуктор, а не одноразовый, как этот... ;-)

センターずれてて草

Harbor Freight sells a measurement tool like this for 77 cents

Environment divided by 2

그냥 디지털 엥글게이지 하나 사자....😂

If you already have a miter saw, why in the world would you bother with this jig? You have a perfectly good power tool capable of making cleaner cuts. This is a waste of time, magnets and wood.

But to find the center of the square block he just used a pencil

Wiertlem do metalu w drenie !!😢

🙃

Pretty good idea except you need to put you block into a drill press vise and bolt it to your drill press table so it doesn’t move once you have it set.

A pencil and a straight edge, a series of lines, done. This is overkill.

Nice tool, but easier with ruler

That's a long way for a shortcut

Пустая работа.

You can tell it's going to be unnecessarily complicated when he pulls out the glass.

Good idea thank you

Do you know what a wooden clamp is? Your safety procedure is pitiful. And you're showing others how to do it WRONG. I know. I taught woodworking for over 25 years.

So now You are ready to drill your hole. So you need to remove the center, Finder, and. to do that you need to remove the dowel so you can take it off the drillbit then you don’t have the center anymore

Qué pavada!

Useless garbage

Yea, in order to find the center of a pole you first buy a whole workshop. Absolutely commendable solution!

Не факт

هنر نزد ایرانیان هست و بس دربست نزد دزفولیان

Это дешевая азиатская подделка на центроискатель от Евгения Чернеги.

А ещё, можно просто ровно просверлить. Если не паркенсон.

Приблуда-Хороший совет для начинающих!! И очень плохой совет по склейке!! Неправильно соеденили-волокна в одну сторону смотрят-выгнет дугой!!

I subscribed to your channel, and had a look. You have a lot of things for all us novice woodworking to contemplate and make life easier. Thank you so much.

Wow, that was absolutely fantastic to watch. No distracting talking, straight to the point. Thank you so much for sharing that with us. I will definitely be making those Jigs. Thumbs UP

И так под каждый диаметр сверла

정중앙에 안꼽히는데요 ?????

PBI seems to be PBI cleaner. Some liquids used for nail cleaning. Has 70% alcohol in it.