Thanks sir for video but could please tell me can i clean it over replacing it
@AutoFixGuru4 күн бұрын
you can try with carb-cleaner
@daviddziadosz6 күн бұрын
If you drop the sub frame, you can remove gearbox, flywheel and repace rear main seal.
@yasiralsabeeh646 күн бұрын
Das Rückfahrlicht ist auf einem Gerät oder auf beiden Seiten erhältlich?
@robertpalmer58036 күн бұрын
If there isnt enough oil in the gearbox it will make a whizzing noise.... .......Bob...Paignton.......
@panumassisod98606 күн бұрын
ใช้น้ำมันยี่ห้ออะไร
@Franciscoman238 күн бұрын
Hello. Did correcting the level fix the noise your transmission was making?
@AutoFixGuru8 күн бұрын
hi , mine was fine
@Tinker_doll10 күн бұрын
Do you have to do both wheels? I bought my own parts and the Audi dealership wants to charge me $500 for labor but I have an appointment tomorrow and it’s going to be $80! I hope they do good
@AutoFixGuru10 күн бұрын
yes of course , both sides always 😊 good luck
@Tinker_doll10 күн бұрын
@@AutoFixGuru thank you!
@SairajPawar0912 күн бұрын
Can you tell where are these drain holes in ford everest 2014 model ?
@jaimyboy1213 күн бұрын
Hey Dude, i got some issues with my radio, i ordered it at audiovolt and i got it now for a couple weeks in my car and i did a factory reset bc it was slow as hell. No i got my buttons resetted as well and they dont work anymore. If i try to learn them in the dont stay saved. Do y got any solution for this?
@AutoFixGuru13 күн бұрын
i wonder why is it slow ? what is the ram capacity on your device ? Normally it should be able to learn buttons again . There is a specific menu for that. Maybe reset again ? let me know if something changes
@jaimyboy1213 күн бұрын
@@AutoFixGuru i bought that ddr4 one 64gb octa core one. Idk why it was so slow, i tried to save my buttons but they wont save for some reason. It says that it saved on a internal sd card but i go back to check the buttons nothing saved lmao. I tried to save it 5 times but nothing works. Do i have to put in an extra sd card?
@jaimyboy1213 күн бұрын
@@AutoFixGuru do you have discord or whatever, im dutch too and maybe we can discuss ab it?
@AutoFixGuru13 күн бұрын
try to calibrate your device , if you put all 5 fingers and hold it on the screen you must enter in calibrating mode , from there you can get to your buttons
@snam79014 күн бұрын
thx man that helped me a lot, like always
@dastanmirzayev713515 күн бұрын
link pls i want to buy it
@AutoFixGuru14 күн бұрын
link is added in description below 👍
@dastanmirzayev713514 күн бұрын
@@AutoFixGuru omg thank u brada
@invisibilty17 күн бұрын
Hello. What is the diamension of oil opening screw?
@ironpaiste19 күн бұрын
Why would you want to replace a clutch of a bullet-proof car ?
@AutoFixGuru19 күн бұрын
clutch was not that bulletproof 🤣
@ironpaiste18 күн бұрын
@@AutoFixGuru I'd say nothing on this car is. Stay way clear of Hyundai.
@Stew187219 күн бұрын
Might be a daft question, however - does the car have an electronic hand brake? If so do you not need to disconnect it beforehand?
@AutoFixGuru19 күн бұрын
good question , you re correct , you need to release e-brake also , I've missed this step in the process of edition
@Stew187219 күн бұрын
@@AutoFixGuru is it only possible by using an OBD tool?
@AutoFixGuru17 күн бұрын
there is a trick with battery as wel
@MoAli-vh8uo20 күн бұрын
Don’t put that colour oil out green original power steering better steering helps the suspension too
@Lucia-Sosa28 күн бұрын
Thank you!!!
@T-Square29 күн бұрын
Thank you.
@sametvarc61129 күн бұрын
why are you replacing the pvc valve? what was the problem
@AutoFixGuru29 күн бұрын
pvc valve didn't do it's job
@sametvarc61129 күн бұрын
@@AutoFixGuru I would be happy if you answer. What are the symptoms of PVC valve failure?
@AutoFixGuru28 күн бұрын
rough engine idle, rich or lean fuel/air mixture, whining noises coming from the engine when accelerating, and poor fuel economy
@sametvarc61128 күн бұрын
@@AutoFixGuru Here is my problem. thank you for replying❤
@vinreytan406229 күн бұрын
Please make for XLT 😢
@teocritor492629 күн бұрын
Hi thanks to your advice now I'm almost done with the job and I just have to close the panel. Can you please tell me the size of rivets I have to use? Thanks
@AutoFixGuru29 күн бұрын
hi , i just measured one and it comes to 14 mm in diameter . Hope this will help
@mohamedanaskp2910Ай бұрын
thanks❤
@Cornpop-147Ай бұрын
as i was changing my lock anyway i thought i would have a tinker with the none responsive lock, i found if leant over to the passenger door and pulled the interior handle and began to toggle the interior lock button on the dash. Somehow i heard a mechanical click and i felt it through the handle too. Well what do you know, the door opens and closes as it should. it doesn't respond through the remote or dash button but did lock on the door button and released to open from the handle. I've changed my lock and all is good now. I thought this tactic might work for someone else whilst they wait for their new lock mechanism to arrive.
@phvdberghe6861Ай бұрын
Hi, heb je nog andere snufjes en weetjes om aan de Mercedes B W245 te werken?
@AutoFixGuruАй бұрын
hi , zoals?
@brendaneze6092Ай бұрын
Does it have some FORD programmeable module installation (PMI) function on it
@darkizofficialАй бұрын
Thank you <3 !!!
@IuLiU149Ай бұрын
5w-30 for 1.4.I-VTEC? honda manual says 0W-20. Why 5w-30?
@AutoFixGuruАй бұрын
0W-20 OR 5W-30 , you can choose
@ladislavbattyanyi1318Ай бұрын
what name it’s that oil
@AutoFixGuruАй бұрын
sry i don't remember
@ladislavbattyanyi1318Ай бұрын
orr any picture from bottle
@MoAli-vh8uo20 күн бұрын
Don’t put that colour oil out green original power steering better steering helps the suspension too
@tommyboi0Ай бұрын
I replaced my actuator with no change, any advice on wiring and how that might be affected. I think everything ohms out to my ECU but then again I'm going to double check. Had a weird wiring issue with my map sensor at the wheel well where the connector attaches driver's side that cleared my flashing glow plug light
@AutoFixGuruАй бұрын
have you tried to scan for faults?
@tommyboi0Ай бұрын
@@AutoFixGuru yes, the fault code is P2016
@AutoFixGuruАй бұрын
are the connectors in good condition ? sometimes they go bad too
@tommyboi0Ай бұрын
@@AutoFixGuru Well the signal wires seem to be good but I'm going to back probe the ground side, just had an issue with that so it very well could be the issue. Will report back. Also fun fact computer probes they use for Arduino boards and bread boards work really well with back probing the ECU
@AutoFixGuruАй бұрын
👍let us know where you've got with it
@JonasLutete-g6xАй бұрын
pls help my behend doors all they are locked and damaged inside now i cant find a way to open as it damaged inside pls help me!!!
@AutoFixGuruАй бұрын
try to use air pumped pillow on the edge of the door , to make space so you can hook with something
@ekay8791Ай бұрын
why are you whispering? hard to hear you over all the water leaking noise in the background
@AutoFixGuruАй бұрын
i was afraid you could hear me 🤣🤣
@khmerMosaicАй бұрын
Looks like you over cut the the bed liner 😅
@Twinturbo_Ай бұрын
At mercedes they suck the oil from the oilpan.
@AutoFixGuruАй бұрын
what do you mean ?
@Twinturbo_Ай бұрын
@@AutoFixGuru from the top with vacuum
@AutoFixGuruАй бұрын
it is not the best way if you ask me
@Twinturbo_Ай бұрын
@@AutoFixGuru i know, but they do
@Drag596Ай бұрын
I think that same year Mazda 3 with 2.5L engine has belt tensioner below. Everything else looks the same but for tensioner, passenger front wheel has to be removed and plastik cover around wheel.
@megabaneen8057Ай бұрын
Thanks
@barenekid9695Ай бұрын
That is one Seriously Poorly engineered GM..Why even Bother? Send it directly to the crusher... Do Not pass Go.
@AutoFixGuruАй бұрын
🤣
@teocritor4926Ай бұрын
Hi , I am trying to make the same repair. Thank you very much for this helpful and nice tutorial !
@AutoFixGuruАй бұрын
glad i could be useful 👍
@black-catmusic3619Ай бұрын
How to set the cylinder back?
@AutoFixGuruАй бұрын
you can see it in full video
@pablo123bАй бұрын
nice review i have the topdon bt800 its well made, reliable and has free lifetime updates too
@rahmanibragimov2804Ай бұрын
Thanks for the guide!
@dastanmirzayev7135Ай бұрын
Wow amazing
@BassicVIC2 ай бұрын
No pressing the piston? No cleaning? No lubrication?? Sorry but I think there’s quite a few steps missing here.
@ImMatMАй бұрын
what happens if you dont do all of this? what can go wrong
@joshrawks212 ай бұрын
What is that part you first started to disconnect? Never seen that on a 9³ before.
@AutoFixGuru2 ай бұрын
LPG injection
@Arz002 ай бұрын
Mechtayu o mazda 3 mps, no boyus’ chto motor razvalitsya :-(
@AutoFixGuru2 ай бұрын
я бы не сильно переживал за мотор
@Arz002 ай бұрын
@@AutoFixGuru esli chto, pomozhesh?)
@AutoFixGuru2 ай бұрын
👍
@bakuiphone35572 ай бұрын
Bu salnikiñ nömresi
@antoniocutrona24792 ай бұрын
Bella
@scumtronic2 ай бұрын
Idk how you guys are yanking these out without undoing the motor mount and jacking the engine up for clearance. Took for fucking ever to just get the pulley out of there. Unbolting it was easy but there wasn't any room to yank it out without it snagging the pump or hitting the body.
@HaydenSchreierАй бұрын
strange mine came right out without taking motor mount off. im uploading a video to my channel in the next few days
@1967jensskov2 ай бұрын
Hello I have changed my temperature sensor, but get no reading in the display. I think I have a bad connection or a broken wire. do you have an overview of the wiring diagram and terminals where I can measure? 2006 Meriva A 1.3 CDTI
@AutoFixGuru2 ай бұрын
hi , have you tried the fuse ?
@1967jensskov2 ай бұрын
@@AutoFixGuru no, haven't checked the fuse. Don't think the temperature gauge has a fuse on its own? could there be another temperature sensor that controls the temperature gauge?