Videos like this always make soldering look so easy. So you know what would happen if I tried to install that HuFlex? First, I would probably have big blobs of solder on the pads, shorting a couple of them. I'd have to fiddle around with them to get them all tinned like they should be, and it would take me 3-4 times longer than in this video. Then, when I try to solder it in place, I'd be moving the iron over the pads toward the chip, and the solder would refuse to go from the pad to the chip pins. I'd spend much more time trying to get it soldered in place and I'd likely end up with some of the pins shorted, so I'd have top spend even more time trying to fix that. In the end, if I even managed to get it working at all, it would look like hell, with big lumpy solder connections. I'm just not good at soldering. I found a PS2 Dual Shock controller in the trash, which had its cord cut off (scrappers cut the cords on things for the copper in them), and I had a couple spare cords taken from defective controllers, so I decided to fix it. It's a miracle that it works, as I ended up lifting a couple of the circuit traces off the board while trying to solder the wires to them, because I left the iron in place so long, trying to get the wires attached. I don't have fancy equipment, I just have cheap pencil style irons. I normally use a small, 15 watt one, but someone once told me that I should be using a bigger one that would get hotter and make things go faster. So I used a 30 watt iron to attach the cord and that was the one that lifted the traces.

Looks amazing! Hopefully they'll let us print our own internals so their queue isn't so long. I'd love to print my own! Happy to pay a healthy fee for that ability, too. BTW, what wireless NES controller are you using? It looks like an original?

Just stick a game genie in your NES, the games will work everytime. You can get em for 10 bucks no modifying anything.

Shame on you for playing in 16:9

Please use different music next time 😂

This is amazing, Tito! The video quality is always amazing. What is the tool that you use at 11:42? It's one of the first times I've seen something like that.

Neutopia and Bonk series are my favourite games from the PCEngine consoles.

At first glance i thought it was q Atari Jaguar.

Right, so gamecube on the DOL-101 without the digital SHOULD be on the cards for this little kit. Neat.

funny enough the first time I took any electronic apart I took my speak n spell apart and tried to hook it up to my TV because I wanted a NES so bad. First time I smelled the "Magic Smoke" of electrical fire. I guess I am lucky my gameboy had triwing screws that would keep me out of it for 20 years. I would have dreamed to have a gameboy that could hook up to a television. This is cool stuff.

A clear Ninten-Drawer would look really nice in that clear case 👍

The Ultra Sonic Cleaner comes in really handy for cleaning PC Engine boards which tend to usually be covered in old flux that is difficult to clean off with the typical IPA 99% and Brush. Another option is to replace the motherboard Pcb. I upgraded my PCE with a new Red Motherboard PCB from PCB Way, Turbo Nanza like RGB mod, Retro Game Restore Clear Shell, Jailbar Fix, new Caps, Modern 78SR no more heat, no more bulky Heatsink but it's only good for systems that use one voltage regulator. I do not recommend it for systems that use two regulator's like the Turbo and PC Engine Duo's, Genesis/ Megadrive Model 1 and the Intelivision which uses 2 7805's, 1 7805/7812. I also replaced the old brittle IDE like ribbon cable used in between the cart slot with a modern custom solution that uses a pcb with a flex connector along with the fpc ribbon. I socketed the Ribbon pcb to the motherboard so i can remove it in case i or someone needs to work on the motherboard again in the future, as the pcb slightly covers one of the main ic chips. That ribbon is usually the main cause for White Screen issues on the original PCE's and Core Grafx systems. The great thing about the Shuttle is it has the Cart slot directly soldered to the Motherboard like the TurboDuo. I hear you can still play PCE/Turbo CD Games off of an EverDrive HuCard.

dose game genie work with it?

ifixit also sells replacement parts for the switch, so even if the screen is dead you could just replace it, not risk getting your Nintendo / you banned, and still dock or handheld.

I think an important question that needs to be asked is if this supports any of the various ROM types (i.e. ISO, RVZ, NKIT, etc.)

Can i ask what flux you used when soldering? it looks nice a flowy with great results :)

PS1 comparability...? (doing a video on all PS1 link games, was going to pick up 2x)

Podia ter colocado o capacitor de cerâmica ou testado antes de trocar nem precisava trocar..

Is it possible to buy these mods fully made from your videos?

An hdmi mod for the ps2? Why not just get a ps3?

since this project has been abandoned, could you put the original video back up? the older shell is available on shapeways & components can be sourced, so people could still do the older mod if the older video were there to follow along with, but this version just isn't and may not ever be available.

Does this technically replace the original output module. I think my board has a faulty output as it's all messed up display

i have an ips scren on my sp, and battery life is pretty bad. only about an hour play time before the red light comes on with flash cart, maybe an hour & a half with legit cart. same story accross multiple batters from multiple sources, so its not just a bad battery. very frustrating. It's getting to the point that I'm considering going back to the ags-001 screen.

Does this work with flippy?

How do you get this version of opl, I can't seem to find it

Will there be direct backup support from disc to micro-sd?

Tito, you did a great job on the Shuttle. Insert applause here!

Didn't see it in the video, but if the WiFi asks for a password it's, mcpadmin. You can also find the information in the mcp start guide online.

Excellent work as usual, you're building a console collection that many would desire.

6:50 - Pop in for 3 minutes on each side until nice a crispy! Yum, fried PCB!

Great job!

Micro usb… really? Not USB C. Yes it’s a low power device but I don’t want to hang on to any more of those vestigial cables.

The PC Engine is such a weird beast. It's considered 4th gen, yet it's technically an 8 bit console reminiscent of a souped up NES running all games in an UNROM mapper configuration.

Anybody has a 3D printed replacement cover for a PC Shuttle ???

Is it just me or is this hilarious?

You know for a cm project a phase change thermal pad might be a better option for a flat pad style heatsink. No fuss with the perfect amount of paste, no mess and you might just get better temps! I've never seen you use it, I've used it on a few projects and each time it shows lower thermals than kryonaut. It's anecdotal but I like it

nintendo already stated that the pin connector was the problem years ago. problem was you coulnt get the part back then. had to send it in so they could do it and charge you. years latter they finally let you order them and do it yourself. then years latter you could order them on ebay for way cheaper

Love these type of videos. If you ever are out of interesting mods to cover for the time being, I'd always tune into a restoration video from you if it means a weekly vid is easier to roll out.

This kid is an engineering genius!

Great video. It may be useful to show how to remove those caps without using a automatic solder sucker. I recently re-capped a tg16 with a basic solder sucker, and it was a white knuckle ride the whole way. Those super narrow vintage tracks don’t take kindly to heat. Pcb quality has come a long way.

The image just does not work no matter which pi or sd card I use. I'm just flashing debian lite and installing it manually at this point...

are there any mods like this for the miyoo mini plus?

You got Mad Skills Kidd👊 is this a Turbo GrafX? I thought I heard you say Saturn??

Hi, Just a minor comment : this is indeed a fairly rare version, but not the rarest: there's the pc boy, which is a clone of ... the pc engine Shuttle ! 😁 I'm lucky enough to have one that works, more or less. 😅

14:34 3mm screw was incorrect 5mm screw is the proper screw 14:39 3mm screw was incorrect 5mm screw is the proper screw 18:18 3mm screw was incorrect 5mm screw is the proper screw These are the only errors I've found so far.

How do I update Swiss on the KunaiGC? I doesn't seem to want to stay on the latest version after power on/off.

I was enjoying this video right up to the point that you did not demo anything of significance on the console. I hope that there’s a better demo of it in the future.

I was enjoying this video right up to the point that you did not demo anything. I’ve significance on the consul. I hope that there’s a better demo of it in the future.

Those soldering tweezer things you have are incredibly cool

I think lining your screws up like that is a good indicator of OCD. 🤭