thank you for teaching me how to weld my yes

Thank you for this video. I appreciate it.

It’s also to allow ratcheting on a fixed square torque wrench.

IS this the same road that C.W. MCall sang about?

Sort of sad to see the Kamala ads begging money on your video.

Just just a little bit thicker wire & a bit longer distance and move whole hand towards the weld and ur golden. Non feeding technique needed and you can focus on other more important things like keeping a tight arc

thank you for the video sir, did you end up keeping the ez window? when you fold the soft top down do you not have to zip/slide the pieces into place? like you just fold the legs in, close the door and take off? i have a JK with zippers and was just curious if i have to zip her up everytime ? thank you!

looking good

Great experience! We were on a honeymoon roadtrip when we discovered a problem with our shocks. Taking a chance, we called and spoke to Neil, who went far out of his way to help us. After speaking, he got the parts overnighted and we drove from NM to meet him and finish arrangements. Not only did he do a fantastic job on our Jeep, he made it happen the next day! We paid a reasonable rate, which was so helpful. We were able to finish our dream trip, going off road safely and with confidence. Additionally, Neil went out of his way to point out local trails and campgrounds. His advice allowed us to see fantastic local sights we would have missed without him. Thank you, Neil!

nice, we just did that on adv bikes 900. that was fun lol

Chief or Police in Teluride said " I want all you asshats to stop going on this trail !"

I had a fun time in my Dodge Diesel 2500. A big truck but it was beautiful. We made many four point turns. A Jeep in front of us tipped on its side and trashed the body. We stood him back and got him on his way. He bought us dinner that night.

Thank you I'm getting ready to do that I hate proportioning valves

What if the e lock move on reverse?

I had to reverse to get my JL rear locker to disengage; I thought the loud metal-to-metal "pop" that followed exploded the e-locker. However, all was good.

You said floor sheet metal next, at 6'3" I don't think it operate a pedal while inside a vehicle. I am lucky to get out. So, button or lift TIG only may work out for the best. I have never owned a TIG or used a foot pedal as best suited for bench work. u would think there both pro's and cons, but controlling amps is important. Mash the pedal to the full on and control amps at the machine. Also, keeping a Stainless Steel brush in zip bag to eliminate cross contamination. Factory exhaust is a 300 series SS forward of the cat and 400 series alloy in the back. Perhaps an exhaust shop is constantly pulling off near new tubing and tossed. Just bring a six-pack nice and cold. Free?

Is that a polara?

Been out of town, and off youtube a while, so just catching up. Looks like you have been busy, truck is coming along nice. When are you getting those cars from out west home?

Metala borrokan🇪🇦. A ver si haceis algo decente. In time⌛️. 🌹⬛️📜⚰️🚬.

I would like to hike it.

Awesomeness

Awesomeness

Awesomeness

Did that pass on a x l six hundred honda years ago

Awesomeness

The red modified at the end belongs to St. Peters pullin team. My channel keeps up with all of our pulls

My great grandfather made that road

Old school hot rod

Heck ya! Extra reach always helps.

Vinyl all the way man definitely will make the truck more unique!

My vote is for black vinyl

Vinyl in gray

For small DIY weldings, blow torch is enough to shielding gas. No matter where CO2 come from. When use gasless welder with gas wire, polarity must change.

problem is if you drive though mud or a pothole full of water , its actuator is going to fail

Does it work with 220v?

It’s exponentially easier if you use an impact 😂

The ratcheting socket is some big brain activity

Is that car on the right a Mercury Comet Caliente ?

How did you wire locker? Do you have wiring diagram? I am planing to use rubicon diff under jku.

Nice! Obviously need this set up to replace my fuel filter on my vehicle.... thanks for the showing this.

63 n 64

Down hill traffic has the right of way?

Good video but I beat mine up out with a framin hammer…Then again,I live in Gulf Shores,Alabama!! ~ROLL TIDE~

Larry thanks again for welding this for me. Had no idea how the oxidation could cause issues and never would have thought aluminum welding would required that much current.

Oooh... (Adds harbor freight cuttoff to list of things to get) 😂

My only gripe with the E locker is that it has to turn about half a turn to engage in disengage. If you’re not used to working with that, it can prove problematic in the field. I wonder what it would take to make an E locker be instantaneous to engage and disengage.

Great editing on this one!