My aunt runs this restaurant. Really good food

will this actually detect engine knock properly by relocating it to the top? doesn't the knock sensor need to be in a specific location? would this only help remove any engine codes?

Does this actually work, and will this stop any codes coming up?

Off the Wall Michael Jackson in the background too!

Hopefully bought the whole jar after just putting the raw dog hand in it 🙄

What great farts are made of.

Pickled eggs are so good

Have fun shitting your guts out today

Bout to smell ripe in there lol

Love it! True Americans!

You rock man, thank u

Watched another video that said a bad EGR sensor can clear up a P0327 code if knock sensor is replaced and still throws code.

Great vid! Some fyi if you replace the sensor with an aftermarket sensor, alot of people report having issues with the cam sensor afterwards. You should replace both at the same time. This vid explains why aftermarket sensors have the issues they do and why it causes that problem kzfaq.info/get/bejne/htCWYNeSyL6znn0.html

You didn’t even show the one you connected to 😂

You never show where the wire comes from on the big harness end? Geesh

So, you "yanked that freakin' plug out a there" and sprayed the jet. Great! So, you've drilled it out, now what? You wrecked it.

Does the knock sensor cause the transmission to act weird? Mine sometimes jerks into gear, sometimes not always. Took it to mechanic and the code was pointing towards knock sensors and tps. Got the tps replaced but not the knock sensor.

Relocating the sensor does NOT do the job, waste of time. REPLACE it properly with an OE replacement, it's not difficult just time consuming. Any organied DIYer with motivation can do this, go watch sarah n tuneds video on this.

Thanks to you my engine is running as new. Go figure why Tohatsu has hidden the idle screw behind a plug!!! Cheers, Richard

What did you have to do with the TPS? Just replace it?

Just what I needed and the engine is finally running at idle again.

Dude! Your the best

John, turn your camera horizontal. It appears we are watching a stick video, tall and narrow. Reason is obvious, you are holding your camera vertical. Notice, every TV screen, computer screen, movie theater screen is orientated horizontal, better known as wide screen. Also, we as humans see our world considerably more horizontal than vertical. Your video has the left one-third and right one-third cut off, that is why I named it the stick video.

I had the p0328 knock sensor code so I relocated it to top of the motor like this and now I’m getting p0327 code..what gives?

what year of maxima? i have an 02 xterra need to relace the sensor.

I looked for this. I still know you brother. Keep living YOUR life, your way! Happy you are happy!!

Thanks Jon, great video...I took my Merc 3.5 carb off & cleaned but idle was still a little rough. I pulled what i thought was the idle jet (also has a spring loaded jet w/ 2 turns) but i think it is the pilot jet, a bit confused. What is the difference in the two? Also, i have a consistent hesitation on throttle up (hiccup) from throttle start position, any thoughts on that problem? Thanks for the help.

Hello, Jon. I realize this is an old video. You are probably the most knowledgeable person that I've stumbled upon in all of these different videos that I've watched of relocating the knock senosr, that's why I am going to ask you my questions and hope that you respond. Question #1: Do I have to use a knock sensor from a Maxima? Or can I use the correct one, relocate it, and just use like a spade connector or something similar? Question #2: Some people have stated that the shielding in the coaxial cable needs to be twisted together, crimp a ring terminal on, and grounded to the engine. Or is it grounded on the ECM side? The shielding is there to intercept electromagnetic energy and shunt it to ground, correct?

Thanks you Jon, great video. I have the 2.5 HP but it's identical to yours. I also found the vent on the gas cap did not work since new. Took the cap apart, and I found there is a blue rubber plug in there that blocks air flow from the vent. Caused a vacuum in the fuel tank and prevented gas flow.

Add 2nd Street Lunch in Roanoke Rapids, NC.

Hopefully someone has an answer for me. So when I opened the coaxial cable, I have 2 wires. A white and black or red, I’m not at home so I can’t remember. I’ve tried connecting just the white. Nothing. The other. Nothing. Both, still get the knock sensor code.

Jon Durham for President. You saved my sailing season. I followed your instructions to the letter and my Tohatsu 6hp long shaft now idles perfectly. I can now motor in and out of a very crowded mooring field without ramming every single boat. Thanks!

Thank you

I have never eaten there but they look like good hot dogs and make Warren’s look embarrassing by comparison.

So awesome and I am so glad you two are so happy. Miss you, but your happiness is most important!

Wanted to ask is the knock sensor still performing on the the xterra

Okay cool

I may sound stupid but I literally just picked up the exact outboard and for the life of me I can't seem to get it to turn, the transom mount will tilt but it won't swivel, u got any tips for me ?

Do you have a part number?

Thanks for the info i been having the knock senson code for a while now and i just saw your video... will do this thank you!!

Love it

Excelente amigo, justo la información que buscaba, sobre el tema de la concion, ya que veo que unos tienen dos cables otros solo uno. Disculpa no escriba en ingles pero mi escritura es muy mala

Will it pass a smog check in these relocation?

That's a great looking hot dog!! Going to try this place. Thanks much

I've wasted 1/2 day waiting for someone to give a ride to get pig tail end to relocate my knock sensor and here I come across your vedio where you explained about 2 wire or 1 wire to the sensor and you explained it very very well on how to just use 1 wire damn if I would've seen your vedio earlier I'd be done.

All the way!! With coleslaw!! That's all the way! Enjoy

Currently going through this. Other videos have left out a lot of useful information that you covered. Thank you! 👍🏻

How do you set the pilot jet or does it even needs to be adjusted?

Thank you so much for making this video! I have a hangkai 6.5 HP outboard motor and it's a copy of the mercury/tohatsu outboards. Your video actually covers the issue I've had with my carburetor. Thanks