Another great Job Mr. Tony. Thanks.

You talk to much bro

You forgot to say no with the index finger after showing the wrong method!

This will make a 2mm hole sir

Children go over center too sometimes. Once they get running, screaming and loolling, it's hard to snap them back.

orbital motion.

lmao, love the needle printer sound :D Isnt that metal spike right through the insulation a huge headpipe? I'd imagine to make the middle part of that tube out of an insulator material

“maybe you see where this is going” I don’t.

Your vise grips need their phase coil adjusted. Probably about an 1/8 turn CCW...

Why is an Acme lead screw (I'm assuming it's Acme, anyway) bad for a CNC conversion, and why is a ball screw better?

i did. i needed to see this

That would cut way faster with like a 600 grit grey SIC stone than with the diamond.

Very impressive!

Your gas hinge system is under load all the time whether open or closed at 30 lbs. What about a two point indent system as in the socket retainer on a ratchet wrench. A small ball bearing backed by a tiny spring?One detent for open the other for closed and the spring pressure on the whole mechanism is microscopic.

Hello! Could you help me with where to buy a clutch for the x axis? Thanks!

Didn’t do the taste test! Would a silicone rod braze to it?

Is pulsed welding and setting the inductance the same thing for us rookies

Good info

Amazing work! Watched it 3x now, instructions unclear, stuck at 3:59! You changed the position in the camera cut and I always get lost on that part

Why not make a steel piece that will last?

“They”, big condiments don’t want you to know they are going….. ***over center***

Thank you this was the perfect info I needed to design a fire arm my self <3

slerpo

3:59 Official name: "Unstable equilibrium." Sure, the math checks out... for now.

Old Tony, what if the double cut pruners had parallel jaws ? Besides costing more...

So, I thought this sounded like you but somehow different, a bit more raucous, slightly more vulgar and significantly more nonsensical. Your voice has taken on a more New York accent than I remembered, the family component wasn’t there but the Star Trek allusion was right there! Also, your production is more TV and less KZfaq….. I must say, I really enjoyed it and at once wasn’t sure if it was you as I was watching on my phone and it wasn’t as apparent as on my desktop. If this is the new This Old Tony, I approve!

You my friend.... are the epitome of what public board of education should be searching for to educate our children. Unfortunately they are more concerned with finding morons to train our kids to be culturally inept.

I know this is old and I’m watching it again… but I’ve always loved when you cut off a line early and never address it. It’s hilarious and one of those small touches that’s kept me coming back for years.

Maybe you can get the 220 amps out of it if you connected it to 480v. But we all know that none of us have that in our garage.

We’d love a video about gas struts!!!

Not trying to tell you how to do your job or anything but you can add small pneumatic caliper/disc with light pressure to be applied towards the end of the rotation if in rapid or constant during feed rotation to apply some resistant force and if need be, edit ur C value or whatever letter it is to compensate for the amount you're short/long radially. Same thing if you're using one of those manual tilting rotary tables, even though they use a worm gear they still jerk due to backlash from time to time and either spit the part out at you or snap the endmill off, best way I found to alleviate that is tighten up the brake (cheap ass little undersize thread bolt in an oversize threaded) hole as much as possible but still be able to turn the hand wheel, and you can mill at half a snails pace at least. juuust a thought..

I needed to see this video. Always been interested in how this works. Thanks so much!

But how could you use singular and pluraral in the same context. Is this how it use to be or is it a joke I just don't get ?

I love you man. You are one of the best at explaining how things work using humor and clear explanation. Bill Nye look out!

Bondhus... That allen wrench set looks a lot like the icon set at harbor freight...

Thank you Dan Gelbart. ;)

Even this video is a learning experience. Now I know why Americans refuse to give us in the entire African continent anything. You are held captive by your government!

I have welded cast iron many times,special cast iron rods,no problem

Poison ivy? Giant hog-weed? And plenty of other delicious plants will do that, just be happy it wasn’t in your eyes.

I have a ligament in my knee that kinda works like this now that I'm 40.

You could make that broken piece out of steel plate and it would never break.

Wow I can't believe this came out 7 years ago, time flies when you're having fun.

WAIT! Did he just say “marbles of engineering”? KZfaq should have some method of rewinding these dang shows. Maybe I could write them a letter to have Tony back it up a little. Anyone know their mailing address?

It’s been a while since I over explained something to my wife!

कोई बताएगा कि सच में पीस फट जाता है

Old Tony - can we have a Maho update?

Over center knees on a leg press

They're called "closures." I worked for Zeller Plastik and I think they had the patent on the "butterfly hinge."

Dave 😂

Could I grind some old dull files into lathe tools? Are they the right kind of steel?