I am glad the video helped you. Thanks for your comment.👍

@@HowToSaveMoneyOnCarRepairs Я уже поменял, всё получилось, спасибо!👍

did you have to take off all the engine mounts?

@@samboon3424 No you don't have take of all the Engine Mounts. Just the the Engine Mount that Covers the Timing Belt. You jack up the Engine by putting you jack under the Sump. The Sump on Peugeot and Citroën Vehicles is specially reinforced for this purpose. Buy a Haynes Manual for Peugeot 207, there is plenty of useful information in there..!

@@HowToSaveMoneyOnCarRepairs Ah ok thanks for clarifying. I do have the haynes manual but it says 'Do not jack the whole car up from the sump,' but then says in the timing belt section to 'jack the engine up from the sump.' So it contradicts itself. Guessing it just means the engine can be jacked. Did you use a block of wood on top of your jack to support?

@@HowToSaveMoneyOnCarRepairs also is there any point in locking the camshafts if you've gotta remove them to get to the cylinder bolts anyway?

@@samboon3424 Nope just follow The Haynes Manual, if you have any doubts...! The Authors are more than Qualified and you won't go wrong, thanks for your Comment and best of Luck..! 👍👍

Go watch somebody Else then Mate, Okey..! 🤔🤔😇😇

It should go all the way in, unless there is dirt on the driveshaft Splines. Also if you have taken off the inboard (Inner) CV Joint then you must make sure (The Spring that is fitted in these CV Joints) is put back. That Spring holds the Driveshaft in Place..on Citroen and Peugeot Cars...!🤔🤔😇😇👍👍

Glad it helped you.😇👍

I agree the Video is Good, Make sure you Subscribe..! Thanks..!

The Camshaft (Sprockets) are secured by Bolts..! Once you remove these bolts, you can slide (The Camshaft Sprockets) off..! If they are a little bit stiff, tap them with a RUBBER HAMMER. A Haynes Repair Manual is a better Reference for all this..! You can Buy Them on Ebay...! 👍👍

@@HowToSaveMoneyOnCarRepairs I have the manual, but they are not really specific about it. I got hem off though. The exhaust one was easy. The intake one was harder because they have put a 38mm plug on it. Probably just because not everyone has that at home. :)

@@HowToSaveMoneyOnCarRepairs What size spanner did you use to counteract the camshaft when you loosened the bolt

@@samboon3424 Hi, i losened the camshaft bolts when the Timing Belt was on. All the spanners you need are in this Set, Buy, US PRO SPANNER SET 14PC COMBINATION METRIC 6-26MM RING OPEN WRENCH SET 2277

The Sealant i used is V-Tech Vital Red RTV Sealant. Heat Resistant to 365C. You can Buy it from Euro Car Parts, Machine Mart OR Ebay. Good Luck with your Repairs.

Ok..!

Me neither..! These are African Roadside Mechanics, trained from 10 OR 12 Years Old by their Master. Most have been deserted by their Parents and left to fend for themselves. They sleep on their Masters Floor...! They have little or no Schooling, they have been trained by their Master to do it this way. Their techniques you mentioned, will make the Brake Pads wear Prematurely and unevenly. Also make the Brakes unbalanced. The cardboard will perish almost immediately and make the Brake Pads Rattle in the Carrier..! So defiantly not done to Manufactures Specifications. I am guessing they want The Customer to return for additional repairs and pay more Money..! 🤔🤔

Buy a new One..! The unit comes with a new seal, so that should solve your problem. They sell them on Ebay..!

@@HowToSaveMoneyOnCarRepairs thank you very much for the tip buddy! I already buy original from fiat with code, manufacture, but it hasn't any seal, nether glue or silicon or rubber seal xD

Headgaskets are a known problem on these Cars. This causes Oil Leaks from the Headgasket at the front of the Engine. If your Car has as many faults as you say then I would suggest you Scrap It and invest your Money in a New Car...!🤔😇👍

Glad it helped you, watch my other Videos..! Thanks..!

Yes, he was a Good Man.👍👍

It is force of habit broh...! WD 40 Prevents damage to bolts and makes them easier to undo. It also prevents Rust that is why, you are seeing me use it here. Every Mechanic has his way of doing things. I believe my methods are within the Guidelines..! Have nice day, mate..!🤔😇👍

It was a successful job performed to Manufacture Specifications and the Car is still on the Road Today. Driving as the Manufacturers intended. So I will ignore your Comment, Mate..! Maybe I will get One Of your Women to Help me next time, ok..!🤔😇👍

@@HowToSaveMoneyOnCarRepairs Hahaha. That's the best response to that

@@niquedegraaff I always reply to Comments. I am on youtube for the right reasons to interact with other People and share knowledge. The Sealant i used is V-Tech Vital Red RTV Sealant. Heat Resistant to 365C. You can Buy it from Euro Car Parts, Machine Mart OR Ebay. Good Luck with your Repairs. 😇😇👍👍

Ok, glad to hear that..! 👍

Hi, i think it should be the Same One for your Fiat Aventura. Check your Local Parts Supplier. Thanks and Subscribe..!👍👍

Yes, you can get better Access, if you Jack the Car Up...!

Remove the Old Bearing and Measure it with a Venier Digital Caliper Micrometer. This will give you The Diamensions for your Alternator then go to RS Logistics and order what you need. Like and Subscribe, Thanks...!

@@HowToSaveMoneyOnCarRepairs wanted to have the bearings on hand before starting the job, thanks.

There are (3) Different Makes and models of alternator fitted to this Car..! in order to get, the Correct Bearing Dimensions for your car...! You will have to remove the Old Bearing and Measure it. The alternative is Replace The Whole Alternator..! 👍👍@@MegaEvoluzione

Great, glad it did...! That is why, I make the Videos. 😇👍

Hi, thanks for the advice..! I will look into all those things and in the mean time Like, Comment and Share My videos, to help me achieve 1,000 Subs.

I don't know, i take my time and do it right then check my own work afterwards..! 45 to 60 Minutes, i would say...! 🤔🤔😇😇👍👍

@@HowToSaveMoneyOnCarRepairs Rocketman 🚀

These Peugeots are Notorious for Head gasket failure around 80,000 Miles..! Maybe that is the Cause of The Engine warning Light..! I have one to sell Maybe you would be interested..?🤔🤔

Can’t be the head, scan returns code P0138 and P0141

Ok Replace both 02 Sensors then but Peugeot and Citroën Cars have a Leaking Head Gasket Fault. @@mzwakhegiftsimelane2680

Great video, where did you buy the tester that wiring was ok?

Euro car parts, just type your registration number in and the right part should pop up...! 👍

@@HowToSaveMoneyOnCarRepairs thank you!

Don't forget to Subscribe, Thanks@@sarahco

Did you put dirty oil back in the car?

Sold the Car 5 Years ago, so that is not possible..! Check out some of my other videos for inspiration..! Thanks.👍

All bulb sizes are in SUBTITLES in the Video. If you watch it fully, mate..!😇

You can google it to find out but the General Rule is, you start with the smallest resistor and gradually go up until the Airbag light goes out..!

Thanks for your Comment..! I just do them to Annoy People..!

Hi, glad it helped you. Thanks for your comment and Subscribe to My Channel, thank you..!

I don't know French but i will answer this one time. This Video Shows the Procedure for 1.2, 8 Valve Engine and 1.2, 16 Valve Engine.

I have a Special Tool, that Props up against the Drivers Seat and brake Pedal. I will show it next time, i do Brake Lights..!

@@HowToSaveMoneyOnCarRepairs Brilliant, I presumed something similar !!!!

you can put your smartphone camera on the ground and record a few-seconds video when you get into car and test the lights

@@PinkeySuavo crap. Yup. Stupid me. Great reply. Course you can. Thanks

@@zzhughesd I just tried it today, it isn't most comfortable but isn't bad idea :D Also, on other video I saw someone put a plank between the pedal and a chair to block the pedal, it could work too, but using camera for me was much simpler :D No problem!

You can Buy them from ebay or rs-online.com Just measure your old bearing so you get the correct size.

There is only (1) Screw for this Lock. It is just under the Rubber Seal (As you can see in the Video). You need a Torx Screwdriver, can't remember the size but you can buy a set of (8) for under £30. The Car belongs to Me and thanks for your Comment...!

@@HowToSaveMoneyOnCarRepairs Good oh just one I have torx kit in tools - one more shot at it!

​@@HowToSaveMoneyOnCarRepairso