Thank you for this video. Helped me replace my wheel faster

The board needs weights to make it level easier but cant do too much either

THIS DONT LEVEL CORRECTLY IT DOES MAKE LOW AND HIGH SPOOTS AND IT TAKES HRS NOT MINS. TRIED THIS 3YRS IN A ROW

Thanks a lot this helped a lot with my Fitbit inspire band. I was so frustrated on why it kept falling off thanks

I did exactly what you said to do and it works. Thank you so much. I even had the same tool. It's called a seam ripper.

Hi, how many bags did this take

What if you have a square pool

How many pounds of sand is this?

Do i need to replace the wheel if the error is uneven ground error? One slightly elevated than the other

Thank you. A similar thing happened on my Charge 4.Cleaning out the gunk fixed it, but the spring feels pretty stiff. Would it be worth taking apart the clasps to clean them and/or lubricate them?

I saved a few $65 ordering the right wheel for Roomba 500, 600, 700, 800 and 900 Series from the iRobot Canada site and then simply changing the plastic housing to fit a Roomba i7. I was however not able to remove the connector pad so preferred to cut the 5 differently coloured wires and then soldering them back on.

Doesn't sand wash away?

Thank you that was so simple😊

One of the clasps snapped n half so it needs to be replaced

Any idea where you can find the replacement part class for a Fitbit charge for? Not the band but the piece that connects the band to the rectangular device. Thank!

Does doing this invalidate the warranty or anything like that?

Should you tamper the sand before leveling it?

The area needs to be watered and tamped far beyond loose sand. Each upright of an above ground pool also needs a small 8x8” concrete landscape pad placed with the lower ring assembled and fitted. Aka you can’t use one section to place pads. Under the pads I would also dig out 6” and fill with crushed stone - with stone dust and water a few times to ensure it is settled completely. Some dog a foot - six inches of stone and stone dust and then top it with stone filled concrete. Why why why asked Nancy Kerrigan…. Google that if you don’t get it- once that pool is filled with 10,000 gallons of water….. ask google how much that weighs. Any upright without a pad block sitting on stone and stone dust watered in hard pack will sink in season one. When digging a pool site - dig the high side - strip the low of grass - never use the loose to build up the low side. If you need to do this you need to consult your building department for guidance. Pools will sink and settle far beyond your wildest imagination if they don’t sit on hard pack original ground with soil and grass removed. Each upright needs to have a landscape concrete pad under it. Once you have this done with a laser level that can light the base 160 degrees-- that will tell you where the pads need to be. Repeat for each side but I prefer to light up all and mark the whole 360 first. All pads must be at the same level. All pads must sit on very solid ground. Once that is done- lay boards over the edges and even plastic across a wheel barrow entry to dump washed sand into the center. Use online calculators to know how much washed sand you need for the pool size. Once that mountain of sand is in the center of the pool area assemble the entire base ring aligned with the pads. Insert the wall and top ring as instructed -- dump stone dust around entire outside perimeter of the pool walls. Soak it down- add more so it is at the lower ring level. This creates forever drainage for the lower ring. I’d add foam on outer walls and cover with crushed stone etc. in the pool- stick the base coping foam to the entire inner wall at the base. Spread the sand and make a berm on the outer edge. Wet it all lightly a few times. Reshape it - wet it- repeat until the contours remain when Lightly soaked. Lay your felt pad down-- use wall covering if you bought it -- install the liner. I hope you bought j hook liner - it is worth every penny. Assemble all as instructed by pool manufacturer - your pool won’t be crooked or random in shape. Way beyond sand shaping or Leveling….

Thank you so much! I thought the bits had broken off and spent a lot of time trying to find something that would work instead of that tiny torx screwdriver I didn’t have and finally came across this to realize the bits were just stuck!

What was the error code it was giving off?

This is the most helpful video ever!! I’ve been trying to get help from Fitbit to no avail. But I used your method and it worked. Thank you so much. Thank you thank you thank you

Brilliant this worked for mine.

Glad I watched your video - followed the steps and it totally worked! Thanks

Thanks so much, was just about to throw my fitbit away and buy a new one!

thank you so much!!!

Your not supposed to use sand to level a pool the sand can be washed out from rain

Your not supposed to use sand to level your pool

Thank u so much it fix the problem I had one stuck and I don’t know what to do but thanks to u watching you it fix the problem thank u

Thank you this was great, gin worked really well!

Thank you 😊 this really worked!!

What kind of sand and how many bags

Will this work using a 16ft board

Will this work the same way using a 16ft board instead of 10

1f+

Thank you very much for this video, it has helped me a lot.

Omg, thank you so much, you dunno how frustrated I have been trying to strap on ny new bands I got from fitbit. Omg God bless you. My fitbit is up and running again!!!! Thank you im so elated 🙏🙏