Can you help me check p/cont temp sensor hight temp 437*
@forklift8024Күн бұрын
Nissan k1b1 model 408 error code appears, what's the problem
@unicarriersservicesupportt879623 сағат бұрын
Drive FET > Short Plaese check FET Drive U,V,W is short
@forklift802419 сағат бұрын
@@unicarriersservicesupportt8796 thakyou!
@lanpham68543 күн бұрын
U04 WFS PRESSURE
@lanpham68546 күн бұрын
Change
@forklift80249 күн бұрын
It's a Toyota 8fb model, but if you press the charging button, it only charges the quality Normal charging is not allowed Do you know what it's about
@unicarriersservicesupportt87968 күн бұрын
We do not know how to fix this problem. We are very sorry. As the truck that arrived did not have internal charging systems installed, we did not encounter many such problems.
@user-tc9li9vd7d13 күн бұрын
Error code 444อะไรเสียครับ
@user-tc9li9vd7d13 күн бұрын
Error code 444อะไรเสียครับ
@unicarriersservicesupportt879612 күн бұрын
หน้าจอครับ
@user-zg6kh6vr5s13 күн бұрын
ขอสอบภามหน่อยครับ ของผมนิสสันตัวBXติดโค้ด Check cont communication problem เข้าไปล้างโค้ดแล้วไม่หายยังขึ้นต้องแก้ยังไงครับ
@unicarriersservicesupportt879613 күн бұрын
โค็ตอะไรบ้างครับ เช่น 444,558
@gyenesjani17 күн бұрын
How can i reach the menu?
@unicarriersservicesupportt879615 күн бұрын
We have recommended clips on the channel, try searching for them in the playlist.
@user-og3vf4lv6q17 күн бұрын
hello i'm from russia i have an E112 error can you help me
@unicarriersservicesupportt879615 күн бұрын
E112 - Pump system. It is the overall error code of the hydraulic system. The subject of the inspection does not specifically specify the cause or faulty parts.But from what we have found, this code problem has the main causes as follows. 1.There is an accumulated heat of more than 60 degrees Celsius from the pump motor causing the control box (PMC) This causes the main control box (ATC) to stop operating the entire system. 2.Check the control box (PMC) whether it is damaged or not by measuring the value using the diode measurement value.If it is not damaged, try storing it in a room with a temperature of about 20 degrees Celsius for about 8 hours. 3.Check the ventilation system on both the intake and exhaust sides to see if it is normal or not.Check whether the operation of the ventilation fan (motor speed) is normal or not. 4.Check the hydraulic oil level, hydraulic filter, pressure relief filter, and whether the quality of the oil is normal or not. 5.Are the motors and pumps operating normally? If you find that the control box (PMC) ,If damaged, replace the new parts, but don't forget to check all the mentioned topics first until you are sure because this may cause the problem to occur again.Clear all error codes before operating in the mode lock book.
@user-og3vf4lv6q14 күн бұрын
Thanks for the answer, the reason was in the hydraulics control unit itself.
@user-og3vf4lv6q17 сағат бұрын
Hello, can you tell me how much the Richtruck control unit itself will cost
@unicarriersservicesupportt879617 сағат бұрын
@@user-og3vf4lv6q 600 - 700 US.
@user-og3vf4lv6q16 сағат бұрын
Do you sell them or can you send a link we'll see and send them to Russia?
@lanpham685422 күн бұрын
Language setting
@lanpham685422 күн бұрын
Laguege setting
@lanpham685422 күн бұрын
Language setting
@lanpham685425 күн бұрын
Set top speed
@unicarriersservicesupportt879624 күн бұрын
Set speed on PARAMETER 1
@lanpham685426 күн бұрын
Erro 419
@unicarriersservicesupportt879626 күн бұрын
FET at the top side of pump inverter unit are short circuited. 1.Check P,N,U,V and W terminals for foreign matter on the them and areas around them. 2.Disconnect motor cable for U,V and W terminals and check connections between motor cables and P,N terminals using a multimeter .Remove any leak and repair. 3.Check motor terminals for loose screw or motor cables for breakge. 4.Repair pump inverter unit. Remark Check for leake between motor cables and truck farme.
@bodareapi29 күн бұрын
E-29
@unicarriersservicesupportt879629 күн бұрын
E29 Self shut system maiffunction
@MarcoAntonioCisnerosniza-zp6qvАй бұрын
Reproducción en castellano
@joshuaadams9225Ай бұрын
Yoo thank you for this video. It doesn't matter where we are in this world all mechanics will find a common ground of language. I work for a Toyota and you literally help me figure out how to get into the menu system do the self-diagnose and it was able to help reset the new accelerator pedal I installed
@forklift8024Ай бұрын
Nissan k1b1 model forklift error code 444 pops up, what's the problem?
@unicarriersservicesupportt8796Ай бұрын
CONT communication (Meter to Controller) # Abnormal 444 Check voltage on pin CN1 (35P) Traction control connecttor harness color (G) when Battery on = 8.7 V. ,when key on = 8.7 V.
@forklift8024Ай бұрын
@@unicarriersservicesupportt8796 thank you!
@forklift8024Ай бұрын
@@unicarriersservicesupportt8796 Then, what is the way to make problem444 disappear?
@unicarriersservicesupportt8796Ай бұрын
@@forklift8024 Have voltage come on change meter panel not have voltage come on change main print board.
@forklift8024Ай бұрын
@@unicarriersservicesupportt8796 thankyou!
@forklifttechnicianguru51262 ай бұрын
Good 👍🏻
@JesusChiquilin2 ай бұрын
Me podrían decir cómo van las rondas de una punta y la otra punta
@agussigitwibowo97653 ай бұрын
How do I enter service mode, what buttons should I press, sir?
@Langcf3 ай бұрын
Same errors came back for me immediately
@unicarriersservicesupportt87963 ай бұрын
Check the quality of the wires and connecting plugs.
@victorestrada10333 ай бұрын
No hablo taka taka
@forklift80243 ай бұрын
I can't charge it with the nichiyu80 series rich model g61 off, what's the solution?
@unicarriersservicesupportt87963 ай бұрын
G61-Voltaga Charge Stoppen. 1. Defect of battery 2.Failure of transformer 3.Detachment of battery plug while charging
@forklift80243 ай бұрын
@@unicarriersservicesupportt8796 thank you!!!
@adamkhaleel81873 ай бұрын
great
@forklift80244 ай бұрын
It's a Uni-Carrier 8 rich model, but it's 092 when I charge it. Why does it pop up?How should I handle it?
@unicarriersservicesupportt87964 ай бұрын
FRB-8A model?
@forklift80244 ай бұрын
@@unicarriersservicesupportt8796 yes!
@forklift80243 ай бұрын
@@unicarriersservicesupportt8796yes!
@forklift80243 ай бұрын
@@unicarriersservicesupportt8796 yes!
@zqlam15854 ай бұрын
E30 ???
@unicarriersservicesupportt87964 ай бұрын
E-30 > ECM system malfunction
@Maghsoud19845 ай бұрын
👏👏👏
@disainkhadafi79985 ай бұрын
Bagaimana dengan cara untuk nichiyu FB20-77 Pak?
@unicarriersservicesupportt87965 ай бұрын
Sorry we don't have this model.
@disainkhadafi79985 ай бұрын
FB20-77
@unicarriersservicesupportt87965 ай бұрын
Sorry we don't have this model.
@ddchannel69536 ай бұрын
เปลี่ยนภาษาจอยังไงครับ ผมเป็นภาษาญี่ปุ่น
@unicarriersservicesupportt87966 ай бұрын
เข้าหน้าโหมด Service DSP. 1.Key on ปกติ แล้วกดปุ่มลูกศรชี้ ขึ้น - ขึ้น - ลง - ลง - OK- ECO - เต่า 2.หน้าจอจะเข้าหน้าโหมด Service DEP. 3.เลือกหน้า 2/4 หัวข้อ LANGUAGE SETTING 4.เลือก ENGLISH กด OK แล้ว Key off 5.Key on อีกครั้ง เรียบร้อย
@TanNguyen-wt8vc6 ай бұрын
can you help me to fix 556 eror codes uni carriers forklift
@unicarriersservicesupportt87966 ай бұрын
We did not find this code in the list.
@TanNguyen-wt8vc6 ай бұрын
@@unicarriersservicesupportt8796 What is the problem and there is error say check filler device timer stop 556. tks you for support
I have a reach truck coming up with Codes - C29 , D33 , G61 , G64 Traction is operational, by Hydraulic functions do not work. Battery voltage is good. Tried with battery removed from unit in case there was voltage to frame, but didn't make any difference.
Ignition signal circuit malfunction [ Check ignition coil ground ]
@user-kt5qx1jc1q7 ай бұрын
สอบถามหน่อยครับอยากเปลี่ยนโหมดตัว P เป็นตัวอื่นได้ไหมครับ
@lanpham68548 ай бұрын
G50
@lanpham68548 ай бұрын
F50
@lanpham68548 ай бұрын
F50
@lanpham68548 ай бұрын
Error F50
@unicarriersservicesupportt87968 ай бұрын
STEER.SENSOR A.Sensor input is voltage low or hight [0.5 > 4.5 V.]
@kowitwanhiang88798 ай бұрын
E24
@unicarriersservicesupportt87968 ай бұрын
Accelerator sensor circuit malfunction - Check voltage supply 5V. when key swtich on [colored wires OR/L] - Check voltage supply 5V. when key swtich on [colored wires OR] - Check equipment
@prasapro8 ай бұрын
1:16
@prasapro8 ай бұрын
Hi sir
@kaliazcueta57288 ай бұрын
How did you access those password menu?
@unicarriersservicesupportt87968 ай бұрын
See on VDO playlist 1F-Serise
@recepureyis10638 ай бұрын
Hello, I am an operator working in Turkey, it gives an E10 error, can you help me, thank you.
@unicarriersservicesupportt87968 ай бұрын
E10 > Joystick abnormal some function 1. Check the joystick all function < lift , tilt , reach and sidelift and its connections. 2) Calibrate the joystick all. 3) Change new joystick.