Hi, welchen Abstand haben die Dachlatten? Es dankt und grüßt MR
@robertbutler80047 ай бұрын
Started off looking good then he frigged up by fixing screws through the flat instead of the rib.
@stanos11688 ай бұрын
💩
@FairplaySidАй бұрын
😂 highly complex! ☝🏽
@patricksaget390911 ай бұрын
Quel est ce type de vis quel embout que vous prenez car j'ai les vis pas la clé merci merci
@Grand.781 Жыл бұрын
😂😂
@ah.sumon1989 Жыл бұрын
Hi,i am from Bangladesh
@ah.sumon1989 Жыл бұрын
Hello
@binodb.k.4352 Жыл бұрын
Parce
@ArpitSingh-sz2dm Жыл бұрын
Hii
@SathishKumar-bt6yp2 жыл бұрын
Why u r in depth side in screw its leak
@sreeramvenkataramesh72862 жыл бұрын
Wonderful Project Works. I Wish You Every Goodness. Jagadesh Garu.
@glenbutler96112 жыл бұрын
Aren't these available in the United States!? If yes, where is a distributor in Florida? How much are they? What's their weight,? Will they hold up to 100 mph sustained winds?
@christophw33882 жыл бұрын
arme Teufel die das so machen ...keine Schraubendichtung bleibt richtig dicht auf die Jahre gesehen
@miorieser32106 ай бұрын
Was können Sie empfehlen?
@ombwallmagiccoat96812 жыл бұрын
OMB WALL MAGIC COAT क्या आप गर्मी से परेशान हैं क्या आप गर्मी से मुक्त होना चाहते हैं यदि हा तो हम आपके लिए लाए हैं गर्मी कम करने वाली बाहरी कोटिंग अंदरूनी सतह को लंबे समय तक ठंडा रखता है
@mahadevappamahadevappa73352 жыл бұрын
J
@TheBareSaint2 жыл бұрын
Real Profi 😂
@TheBareSaint2 жыл бұрын
Profi 😂😂😂
@edsonchakanyuka37332 жыл бұрын
That screw should be on top of the rib not in the valley where water runs. That roof will definitely leak smdh
@atillausta85142 жыл бұрын
hello take it easy
@khanbrotherfiberglass53672 жыл бұрын
Subscribe kar diya hai sir
@khanbrotherfiberglass53672 жыл бұрын
Subscribe kar diya hai sir
@AugustKling2 жыл бұрын
Bullshit to screw on ground! / Screw bullshit to the floor!
@AugustKling2 жыл бұрын
Am Grund schrauben? So was machen nur Pfuscher.
@saidfarass39552 жыл бұрын
kzfaq.info/love/hleeTSjI_MmYtll07kDrHg
@saidfarass39552 жыл бұрын
kzfaq.info/love/hleeTSjI_MmYtll07kDrHg
@juracisilva36982 жыл бұрын
Show de bola muito bom
@SP-cj2wz2 жыл бұрын
S1959
@musicmedia12372 жыл бұрын
It's very interesting back ground music. Which is this music.. can u share
@rohmarlungtau5992 жыл бұрын
Absolutely wrong work very bad
@burhanceyhan11262 жыл бұрын
Su yoluna vida atılırmı hıyar
@favioayala97162 жыл бұрын
Disculpe las coberturas llevan un plástico pegado al metal ese plástico se lo retira antes de instalarlo o es recomendable no retirarlo
@vladospasojevic13932 жыл бұрын
koliko.kosta po kvadraty lim
@wuilsongustabolopezlopez51722 жыл бұрын
Que presio tiene el pie
@bhanwarlalarya56632 жыл бұрын
मगरी और चद्दर के बीच में जो रबड़ का पैकिंग है वह कहां पर मिल सकता है
@davidantoniosierracaceres22302 жыл бұрын
Por que lo atornillan donde corre el agua
@sekarpandurangun10112 жыл бұрын
I need screw and tape please send contact number
@joaouezadasilveira17942 жыл бұрын
Perfct
@goyani86653 жыл бұрын
भारत मे हीन्दी लीख्ऐ यार अंग्रेजी मे कयु भाडते हे यार 🙏
@nareshsatnami63893 жыл бұрын
Call me 7806020065
@leocadioevaristorojassalaz90453 жыл бұрын
Cuanto mide una o lancha de alucin
@marionunez95163 жыл бұрын
You need a sure line before screwing! To get it neat and perfect And the screws are in the wrong place. This is why you get THUMBS DOWN.
@govindsahu1923 жыл бұрын
🙏🙏🙏
@govindsahu1923 жыл бұрын
Kan chahi ye
@cangzhoufamousinternationa79273 жыл бұрын
roll forming machine If any need, please contact: Email:[email protected] Whatsapp:+8618713641935
@cangzhoufamousinternationa79273 жыл бұрын
roll forming machine If any need, please contact: Email:[email protected] Whatsapp:+8618713641935
@cangzhoufamousinternationa79273 жыл бұрын
roll forming machine If any need, please contact: Email:[email protected] Whatsapp:+8618713641935
@ryszardgrabowski46033 жыл бұрын
a gdzie wentylacja
@R4TEL Жыл бұрын
a po co Ci tam wentylację? A zresztą, to nie jest aż tak idealnie szczelne.
@thomasschafer72683 жыл бұрын
The screws are to small. And why don't you drill the screws on the top of the profil. There's no water.
@nikhilbharti35783 жыл бұрын
Can we use normal drilling machine for this.?
@thomasschafer72682 жыл бұрын
@@nikhilbharti3578 yes. the screws cut for themself