Jeremy Thomas

Пікірлер

@bryanmeier272xp8 7 сағат бұрын

wow thats a strong running little 260 that bad boy looks like it cuts as fast as my ms310 i have 2 260s think one of them is a pro both the oilers went i was going to fix but i put off on them because wanted to learn to port first think i have like 11 saws lol only got like 5 going right now missing my 046 and ms460 tho there down so useing my back up 372xp

@bryanmeier272xp8 8 сағат бұрын

that is Impressive for a 55 wasn't inspecting that imma have to keep a eye out for a 55 now

@bryanmeier272xp8 8 сағат бұрын

im a fan of the 357 i call it a mini 372 looks like the rankers were little hungry lol reminds me i gotta do the top end on my 359 oh question is the 61 have the same bottom end as a 272xp or what saws have the same bottom end of a 272xp i have a 272xp ran great for like 6 months died slow like it was running out of gas i replaced top end i have gas and spark and it wont even try to start i was thinking maybe crank seals but havent split any cases yet

@bryanmeier272xp8 8 сағат бұрын

i know and do work on saws a little as far as doing a top end and rebuilding carb haven't split any cases yet and i need to i have 2 ms460s that need crank bearings but anywase my question is everyone sez a 036pro is the same as a ms360 i have a 036 pro has alot of compression its oem stock and my buddy has stock ms360 and the 360 kills my saw even my ms310 is way faster then my 036 pro are the top ends the same on the ms360 as the 036pro

@ronaldrvvanhook1437 14 сағат бұрын

A bit low in the water, but I'll bet you could put a few more on there

@user-ls9qi3jx6b 2 күн бұрын

Где здесь 61 husqvarna? На видео только 357 husqvarna...

@shaun4bigblocks993 13 күн бұрын

I think you made a mistake- that was not a 346XP, but rather a 346 XP NE with the chain cover painted orange, or you meant to say 3.4hp in the title. It also helps to add saw ID captions if you are not going to go in logical order. Lots of backwards going on here...

@jeremythomas9134 13 күн бұрын

@shaun4bigblocks993 the 2nd saw has a 44.3mm tip end on it. Which in fact makes 3.7 advertised horsepower. As far as going in any kinda "order"....well, just use your imagination I guess cus I'm going to continue doing things however which way I want. Thanks for watching 👍

@williamevans6554 Ай бұрын

Did it run ok with the pop up piston? I just ordered one from hl supply for a 261c that came cheap because the guy couldn't sharpen his chain lol never seen a bar and chain that had been so roughly treated.didnt want to spend much as I'm not sure what other damage has been done.

@jeremythomas9134 Ай бұрын

Yes it did, no complaints at all.. I use hyway Pistons quite regularly. Never had one issue outta dozens of em. Nice pistons

@williamevans6554 Ай бұрын

@@jeremythomas9134 That good to hear, did you widen the exhaust or anything or just leave the cylinder stock ?

@jeremythomas9134 Ай бұрын

@williamevans6554 I left this one stock. Just a simple rebuild for a local customer.

@williamevans6554 Ай бұрын

@@jeremythomas9134 do you use the hyway circlips or re use the oem or new oem, I hear lots of different things about this?

@jeremythomas9134 29 күн бұрын

@williamevans6554 I typically reuse the oem circlips. That don't always happen, sometimes you'll lose one or whatever the cause may be. I have used the supplied aftermarket clips also though. Both hyway and meteor. Never once had a problem with em man. The main thing with any circlip imo is getting em installed properly and darn sure they're seated properly, without bending em up. I think that's where ppl have issues myself....cause I sure haven't.

@agt155 Ай бұрын

Stihl bar?

@jeremythomas9134 Ай бұрын

Yep. Bar for an 025. Works just fine and oil hole lines up perfect

@LordEthan2 Ай бұрын

2nd saw sounds a bit tired haha

@jeremythomas9134 Ай бұрын

Second saw is a 56cc saw. I think you're tired. Hahahaa

@LordEthan2 Ай бұрын

@@jeremythomas9134 haha ahh right missed that

@jeremythomas9134 Ай бұрын

Ethan is happens I suppose. I'm not mad...I'm just disappointed. Hahahaa jpn man

@bushleague3472 Ай бұрын

Is that a 24" bar and skip tooth on that 61?

@jeremythomas9134 Ай бұрын

Yes sir I believe it was skip tooth chain. 24 inch bar yes

@bushleague3472 Ай бұрын

@@jeremythomas9134 Thats fairly impressive performance for what they generally cost. Thanks for your response.

@jdisellitboy815 2 ай бұрын

Awesome video man I appreciate it

@JoeMcKinney-dy7lc 2 ай бұрын

😅

@jeremythomas9134 2 ай бұрын

Do you feel like your making a statement Joey? You got no vids...no pic. No nothing. 181 likes...what is it you're doing? Lmao ima laugh at you fool. But with no gay emoji

@garcoleuphrates4734 2 ай бұрын

Must have jiggled that carb for 2 days trying to see how to remove! Saw your video and the torx screw buried in the handle -- WOW! THANKS!

@michaelteti5148 2 ай бұрын

You mentioned these were simple to work on I have a271 looks identical to the 261. Had to replace fuel line found it to be tedious to say the least every thing so tight, but got it done. Thank you for your video helped a lot.

@dougkahler7152 2 ай бұрын

I’ll keep my 036 keep your Husky

@ericfuller6326 3 ай бұрын

Nothing like a croc full of chips. Lol

@user-qz1gr1bf1b 3 ай бұрын

Awesome saws 👀 👏 😎 I purchased a 5105 off eBay and be here this Wednesday 😀 very excited. Looks like very good condition 👌 like you have fixed 👍 Washington state coast 😂🦅🦅🦅 Gray Eagle 😊

@bigboogs46 3 ай бұрын

I'm thinking about doing the same setup on my 036 pro. Just curious, did u run a squish test on it after doing the base gasket delete? Should I do a squish test? Since it is a pop up piston, do i have to do the squish test differently?

@jeremythomas9134 3 ай бұрын

What brand pop up did you go with? Just curious....but no that shouldn't matter. I built a lot of these and I've always had room for a gasket delete. But still you should always check to make sure that you do.

@bigboogs46 3 ай бұрын

I went with the stihl 036 hyway titanikel cylinder kit with pop up piston thru wolf creek.

@jeremythomas9134 3 ай бұрын

@@bigboogs46 I've used that same kit on a ms360. You'll have room for a gasket delete. My kit didn't have the pop up tho. You'll be fine

@bigboogs46 3 ай бұрын

Thanks, I appreciate it.

@jeremythomas9134 3 ай бұрын

@@bigboogs46 you're welcome

@Pavel-gx4wk 4 ай бұрын

Скажите кто знает,можно ли поставить поршневую от 353 на 350 хузварну ,спрашываю потому что у нас в украине нет в продаже поршневой 44мм?

@Pavel-gx4wk 4 ай бұрын

Какие цылиндро можно поставить на хузварна 350?

@christianpaquet509 4 ай бұрын

Very nice video, thank you taking time showing us uow to do. 😊

@CristianAdkins 4 ай бұрын

I have a 036 and i put a new top end on it. The one i bought doesn’t have a screw to hold the to hold the top plastic in place what should i do?.

@jeremythomas9134 4 ай бұрын

Heat up the one on the original with a torch and unscrew it with pliers and put it in the new cylinder

@jgbelmont 4 ай бұрын

Nice chips. Chunk looks wet.

@erich0104 5 ай бұрын

Die schneidet 👍

@HungMay365 5 ай бұрын

Helo

@jackfrosty79ify 5 ай бұрын

Stock they rip

@cuaxichbai 5 ай бұрын

Hello

@chrisbloodshoofd 5 ай бұрын

The Stihl is a saw that a homeowner could push through on the dogs with a dull chain, the Husky will run faster and smoother than the Stihl on higher rpms with a sharp full chisel chain, without being dogged in. Like both saws , but love the 3 series Huskies. ❤

@christianlonnberg7975 5 ай бұрын

What was that white grease you put on? Some kind of gasket maker?

@jeremythomas9134 5 ай бұрын

The stuff I put on the cylinder is threebond 1184 gasket sealer. It's good stuff

@seemeeseeu 5 ай бұрын

New Sub, Thanks for this Awesome vid!!!. Just got a 261c that's seen better days...this is helping me refresh it. I have one question: I am using Lucas assembly lube-semi synthetic for rebuild-Do you think this is a good idea? Thanks Again!

@jeremythomas9134 5 ай бұрын

Yeah that certainly can't hurt anything. Good idea to keep things lubed up

@DanBuch-vt3rh 5 ай бұрын

I really wanted to watch a video but whatever you were sucking on was annoying. Next time try not to suck on something when you’re doing a video.

@bernalleiton3428 5 ай бұрын

Muy superior la stihl

@ericfuller6326 6 ай бұрын

I find my 670 is really heavy is the 61?

@jeremythomas9134 6 ай бұрын

They don't feel very heavy to me. I just recently bought a dolmar 143. 17 pounds powerhead only. Now that one feels heavy to me. Close to the same weight as a 395xp

@davidjohnsen663 6 ай бұрын

Hey again heh, Something strange happend, the dealer`s small engine mechanic, whos a veteran and our local pro to say it in that way, tried to replace my cylinder and piston today. I owe a 2152 jonsered, or a 353 if you will. the new parts was a un-original 346xpg, or a 2153 cylinder and piston. he told me : the original inside my 2152 was a 45cc, and the one i wanted inside the jred, the (346xpg) was a 44.5cc so he said he couldnt fit them could it just be as simple as someone just sent me a wrong cyclinder? x) anyhow, good evening :) PS: Could it also be that there are different year models with slight modifications between the saws?

@jeremythomas9134 6 ай бұрын

It's really hard for me to help ya without seeing anything in person. You want the 44.3 millimeter cylinder kit though. If that's what you have it will work

@davidjohnsen663 6 ай бұрын

@@jeremythomas9134 thnx!

@jeremythomas9134 6 ай бұрын

@@davidjohnsen663 you're welcome

@TheDennys21 6 ай бұрын

The Husky 61 holds a special place in my heart because my dad had one for 33 years and then it was stoled.

@ranieremendonca6370 6 ай бұрын

👍👏👏👏👏🔥

@davidjohnsen663 6 ай бұрын

Exacly what is the difference of these saws? Ive got a jonsered 2152, but want to convert it to 53, and i cant get the dealers to tell me how many parts i need. U seem experienced

@jeremythomas9134 6 ай бұрын

The only difference is the cylinder and Pistons. Case is exactly the same. All you need is the 346xp cylinder and piston. I'd recommend a metal intake clamp if ya don't have that already.

@davidjohnsen663 6 ай бұрын

@@jeremythomas9134 cheers mucho apprechiazo.😝 BUT does the plastic parts ( gass intake)also come with the 346 cylinder, or only the metal part?

@davidjohnsen663 6 ай бұрын

I have a realy mint 346xpg NE. And a unused 2152. I want to make it a 2153, and Even buy the house cover that shows2153, Just so itl be true 😄 so ill have someone dismantle the 346xpg and put it over the 52. Just hope they will be as malticilous as you were

@aBigMeanie 6 ай бұрын

oh my. have you ever worked on a chainsaw before?

@aBigMeanie 6 ай бұрын

seriously? you don't have/can't afford a torque wrench? lol.

@jeremythomas9134 6 ай бұрын

Seriously? Ya need a torque wrench to build a chainsaw? That's a dumb comment bud

@aBigMeanie 6 ай бұрын

if you think theyr'e just toys then ok. real engines need proper tightening specs. @@jeremythomas9134

@thaiscosta6371 6 ай бұрын

Qual das duas e melhor??

@ceejay6882 6 ай бұрын

When you rebuild M-Tronics and there's no information and no smoking gun on why it was running too lean, are there liability concerns for a potential send back? The MDG1 device is pretty much out of reach for most back yarders so there's always a question mark on what the microprocessor/solenoid is doing with the carb.

@jeremythomas9134 6 ай бұрын

I usually chalk it up as user error. Especially when 9 out of 10 of the saws I rebuild run just fine once put back together properly. Some.of these people out here just pour a little bit of oil in each tank of fuel. I know that cause several of these guys have fessed that up to me. That and dull chains. I see it all the time

@carbonEYE007 3 ай бұрын

Ethanol gas is what is killing these saws in many of cases. usually due to fuel separation.

@1bknlove 6 ай бұрын

Awesome! Been thinking about up upsizing my ms290. Thanks for the video.

@OldGriz406 7 ай бұрын

Two year old video, but was very helpful to me. Thanks.

@user-vq7xr9qq1p 7 ай бұрын

357 интереснее штиля и порезвее, по мощности слабже его, сравните 036 с хускварной 262xp

@StumpkillerCP 7 ай бұрын

Why? The 353 e-tech has a 1.7 cc larger displacement that the 346XP. You're going backwards. The sharper chain would be the advantage to either model. The XP runs a little faster . . . but only a tiny bit faster. Maybe 8%. Easier to buy a new & larger chainsaw than all that. I have an 18 year old 353 e-tech that keeps feeding the boiler and wood stove. Great saw as it is.