Hey there, rebuilding my 04 B6 4.2 , was wondering about how to set the timing when you assemble the heads back onto the motor?
@markb6s4Күн бұрын
@@SKLLY-gg1nf go into detail in this video. And the next one following that video has the assories going on. Feel free to search around on my channel kzfaq.info/get/bejne/Y7-ZlJWql5mdpps.htmlsi=xpg6s_pltbVCdbLM
@maratmuhanov90402 күн бұрын
Hi, great video! I have question do you still have the old fuel pump? I need it😢
@markb6s42 күн бұрын
@maratmuhanov9040 hi, unfortunately, I really have no idea where my stock fuel pump is. I know I never sold it or thrown it out. And right now it's not easy for me to go find it since where all my stock stuff is far way from where I live at the moment
@maratmuhanov90402 күн бұрын
@markb6s4 OK thanks, so I will go for walbro as you advised thank you anyway!
@maratmuhanov904019 сағат бұрын
So today I'm changing fuel pump same brand what you advised let see how it's work...
@23bdubballa3 күн бұрын
Hey friend thanks for this video saver $$$$ the stealer wants over $1000 to do this same job a me Cadillac smh anyway that barb you use can you confirm that thread size and does it screw into the same threads as the plastic tube????
@markb6s42 күн бұрын
This is the drain plug details (VW Porsche Auto Trans Drain Plug - Genuine VW WHT005510) and the size it says is M10x9. Please verify if this is correct. Can't remember off the top of my head. And the plastic tube I used for the pump was the right fit for the barbs
@SegaSavageMusic4 күн бұрын
😤😡💪🏽 I feel you
@chikmnunget4 күн бұрын
🥴🔥
@damonbrace82527 күн бұрын
All for nothing!!... They are built wrong!!!.. with cheap materials..some happen at 50..60.000 miles... Really??.. you spend 90...100,000$ and doesn't last 60,000 miles??????... Nothing new!!!.. who is the fool..???
@male07mdl7 күн бұрын
how are the lights holding up? did it have any issues?
@markb6s45 күн бұрын
As of now. Aug.24,2024 I have had no issues with the lights. And from what I have read in the past some people may not be so lucky and have had some issues. Again I don't daily drive the car. Don't know if that adds any value to my statement that I haven't had any issues
@kenmcfayden21608 күн бұрын
7:19
@TwoTwenty713 күн бұрын
Thanks man!
@ernestvogel879115 күн бұрын
Do you have a shop around Denver?
@markb6s415 күн бұрын
@@ernestvogel8791 I do not. All work is performed in my garage
@asetunc117 күн бұрын
Good job 🎉
@markb6s417 күн бұрын
@@asetunc1 thank you
@user-zk3ut5do7g21 күн бұрын
Excuse me How to change Audi Q7 Center Differential Oil?
@markb6s420 күн бұрын
I have links to those videos in the description part
@azthundercloud21 күн бұрын
Works. The way you explain vs. Audi forum is night and day😊
@markb6s421 күн бұрын
Quick and easy feature to do!
@jairocalderon328621 күн бұрын
What year is that Q7? Can I that with an old 2007?
@markb6s421 күн бұрын
This is a 2013. Soni know this works for the 2013-2015 models. As mentioned towards the end of the video I am not sure it it can be done or not for the 2007-2012 models
@Baggotbigger26 күн бұрын
Thinking of starting a b6 a4 avant- project. Can’t find any options for aftermarket bumpers or fenders do you have any suggestions
@jagerthedog437826 күн бұрын
Bro, you're inspiring me to give up on selling my b6 and actually learn about cars by working on it, big thank you!
@markb6s426 күн бұрын
@@jagerthedog4378 if you haven't already. Make sure to check out the engine rebuild parts 1-14 on my channel. There you can see the whole process and also in hopes that it is of usefully information and you learn from them.
@jagerthedog437826 күн бұрын
@@markb6s4 Thanks!
@edgarv681326 күн бұрын
Great job. Love the attention to detail
@markb6s423 күн бұрын
Thank you very much!
@MiniFun9228 күн бұрын
Not the best explanation. What do u mean car is on? Gearbox is still when its on. U need to fill it with aproc amount. Disconnect. Run a car, shift though gears. Reopen fill some more till drips. U can repeat that once more to be safe. Make shure its level.
@markb6s428 күн бұрын
@@MiniFun92 that the engine has to be running, and then going through the gears. All at the same time being within the right oil temperature range.
@user-ky2cz7cd4yАй бұрын
My 1.8t looks almost identical to your car others than hood vents and yellow calipers. Truly amazing
@markb6s4Ай бұрын
@@user-ky2cz7cd4y thank you. Cant go wrong with that color combo 😁
@SlowcarfastbeansАй бұрын
Watching this while I’m also doing the same thing.
@markb6s4Ай бұрын
@@Slowcarfastbeans big game changer as compared to a NA setup
@bedlfit2198Ай бұрын
I’ve got a b7 s4 Avant … lots of fun mods planned. Mine is dolphin grey which is dang nice when it’s all buffed out. The brushed aluminum trim is a nice addition with the dolphin grey too.
@MasonDesjardinsАй бұрын
Little late to the party on this one but I’m currently trying to lock my timing in place. I got the Schwaben timing tools and was wondering where you put the crank lock pin? Do I need to use it or are the plates to hold the cams in place enough?
@markb6s4Ай бұрын
@@MasonDesjardins so I failed to mention towards the beginning of the video the crank lock pin does need to be installed. I installed it in a previous video before this on. I only mention removing the pin once it's time to rotate the engine. I talk about it at the @24:48 min mark about the removal. For installing the crank pin. Remove the cover that's covering the to get to the crank. Once removed rotate the engine till you see the hole where the crank lock pin goes. You'll be able to notice it. Once the crank pin is all the way threaded in. Then go ahead and start removing the timing components. Install the new timing components and then as in the video at the 24:48 min mark the pin can be removed
@markb6s4Ай бұрын
@@MasonDesjardins the plates to hold the cans are not enough!!!!! Please use the correct tool on the cams side to hold it in place along with the cam plate tool. do not rely on that plate only. its only to help align the cams in correct place.
@dangeloross5541Ай бұрын
how much was it for the sp kit?
@markb6s4Ай бұрын
What's listed on the VF engineering website
@eugen8498Ай бұрын
Lip it's from m5 e60 ? Or m5 e39 ?
@markb6s4Ай бұрын
@@eugen8498 e60 m5, I personally liked how the lip goes along the curvature of the B6 bumper. At first I had a universal one and the curvature really didn't fallow the lines of the bumper
@David-yy7lbАй бұрын
WTF is wrong with 1 timing chain and 1 camshaft
@markb6s4Ай бұрын
@@David-yy7lb in a previous video I explain as to what happened to the engine. since the engine was going somewhere else to be rebuilt. I didnt want to cause any more damage to it when removing the timing.
@AlexrivasmusicАй бұрын
How did you put the Q7 on jack stands ? I have one and can’t find a central jack point to lift front or rear and out the stands . Thank you for this video!!
@markb6s4Ай бұрын
@@Alexrivasmusic for the rears I use the rear differential
@raddrock559Ай бұрын
Can I do this with paint and brush? Wouldn't require any taping and removing
@markb6s4Ай бұрын
@@raddrock559 I've seen there is a company who sells paint for calipers that use a paint brush. But I don't know the name of it. I think I saw it on Amazon. As for the result I can't speak on that.
@allyouaskfor2 ай бұрын
An easier way to put the needles back to where they need to be without using power is by just pressing them back on to the pins and rotating them counter-clockwise and stopping them at 0. Make sure you are moving them counter-clockwise though! The best way is to connect power and turn it on, connect to 17 - Instrument Cluster with VCDS and perform an output test which will locate the speedometer to 100, temp to 90, and I forget the values of the other two.
@markb6s4Ай бұрын
Thank you for this very helpful tip!!!
@RadicalUnionist2 ай бұрын
Is that filter serviceable without pulling the transmission? Ive seen a lot of people saying it isnt but ive also seen them for sale. Trying to get everything in place for service soon and would pike to chamge the filter if possible. Thanks for the video and your help!
@markb6s427 күн бұрын
If I'm understanding your question correctly. No need to pull the transmission. The transmission mission stays in place. The filter can be easily assessed from the bottom.
@markb6s427 күн бұрын
Also I have the full video of the service down in the description portion of the video with the link to it
@RadicalUnionist25 күн бұрын
@@markb6s4 Thanks man. I mistakenly thought this Aisin 8 speed was the same as in my BMW. It is not. The one I have does not have a pan.
@kaore82382 ай бұрын
Throw it all in Mark, im all for it bud lol
@VehicleLivesMatter2 ай бұрын
I approve this message
@trppytoes75062 ай бұрын
What audi is that going on?
@markb6s42 ай бұрын
B6 s4
@rogerhenry34812 ай бұрын
...or vacaions, or fancy clothing....or restaurants....
@Hemi317.2 ай бұрын
No, cars are the only correct answer.
@oerlikon20mm292 ай бұрын
You aren’t broke, it’s just all your money goes into cars
@justsomeguymustache2 ай бұрын
you arent broke, you just spend all your money on a depreciating asset (your becoming broke)
@UndaCuvaChikin2 ай бұрын
@justsomeguymustache Exactly. Cars never, and I mean NEVER, go up in value. That would be crazy. Insane, even.
@justsomeguymustache2 ай бұрын
@UndaCuvaChikin i feel like the only time a car would go up in value is if its an old car that was more common but became very rare, i know those exist and definitely can go higher than original market cost if there are only a handful left, but aside from that, cars are terrible investments.
@tangogolf8462 ай бұрын
Much as I love cars, dudes right. 😢
@yungdogger58972 ай бұрын
My a6 3.0t currently has a hole in the flex pipe surely this is my perfect reason and time to do long tube headers and a cat back
@DaTwinzz2 ай бұрын
That's what I did when my cats were took a shit and exhaust was blowing nasty smoke on my b5 s4 so I did catless downpipes and exhaust
@CoryDesilets2 ай бұрын
Your videos have helped me tremendously. Much appreciated good sir! And glad to see the community supporting one another 👍
@markb6s42 ай бұрын
Happy to hear these have been of help. And excited to see your set up thrashing through the streets... Mexico streets 😉
@amtuned10862 ай бұрын
You are very welcome Mark. It’s nice to see this coming together! Nice shirt 😊
@markb6s42 ай бұрын
i think the shirt gives me super powers and adds 15whp to the car
@nathantroutman47282 ай бұрын
I thought you were going with the rear turbo mount
@markb6s4Ай бұрын
@@nathantroutman4728 that's way out of my knowledge. Also with some fab work to which I have zero skills in.
@paul282 ай бұрын
Just amazing.
@markb6s4Ай бұрын
@@paul28 thank you
@paulbreaux9092 ай бұрын
Does anyone have an updated procedure for VCDS? The one shown no longer works.
Just recently did this and it's still the same process from when I 1st did the video, strange that it wasn't for you. And thank you for showing another way too
@georgiebell70643 ай бұрын
Thanks 🙏 your video was very informative and good application you did mechanical first then PMC
@markb6s43 ай бұрын
Thank you, happy to hear this was of help. Yes I did all the mechanical stuff first then flashed the tune
@CrazyYorkX3 ай бұрын
the tiptronic does feels weird from 4 to 3 in my car, and the throttle blip is not strong. For me it is consistent at track day but I wish to have a software that can increase throttle blip like xhp tuning to bmw. Then I believe it will be great for a while.
@m6trix8463 ай бұрын
Jackal tuning makes a tcu tune for the b6 and b7 S4. makes the shifting much better
@CrazyYorkX3 ай бұрын
@@m6trix846 I already have the both tune for years. I have asked Tony several times and he said the more TCU feature belongs to custom tuning so that it will have extra charges.
@opprometheus3 ай бұрын
Fluid temp is not such a big deal. Just drive the car a couple of blocks if the outside temp is around 50 to 75 degrees. More importantly, is to the check the level with the engine running like stated here.
@xxkopa62313 ай бұрын
is 3ft 2x of 5/8 hose enough?
@markb6s43 ай бұрын
This all depends where you plan on placing the catch can. It's been a very long time since we've done this. I would just a any string and dona rough idea the path you want to take and measure the string and give your self an extra feet for insurance purposes
@slammedeuro1043 ай бұрын
Are you guys running lower compression to run higher boost? Or just running really low boost? What boost pressure you expect to run on the setup?
@darrinscoilsclouds14983 ай бұрын
seems dumb to spend all that money for 600hp. im close to that in my 2020 s4 with 5k invested and with another 4k ill be at 775hp🤷♂️
@markb6s42 ай бұрын
And that can all change. When I first got into the boosted life I said to myself if I can make 500whp I'll be happy. But then now I'm in the process to push some more power. Give it time 😊
@ukaszburejza9323 ай бұрын
Love it. This is going to be a wild project 😍. But personally I think this set would be perfect with 8hp 😉
@jon21273 ай бұрын
Keep it up Mark! Glad to see you’re still at it
@markb6s43 ай бұрын
Been a little slow on making videos but little by little! Hope all has been going well!
@Red6er3 ай бұрын
very cool build, covered a lot there
@markb6s43 ай бұрын
There for sure was a lot of information covered. I think others use this as a guide and start in their rs4 twin turbo build builds 😁