Great video…. Going to do mine soon. No idea of proper torque for bolts? Now I see it looks like the bolts are reverse thread which I wouldn’t have suspected unless the camera is playing some tricks…

Thank you Ken. I just bought a very clean '97 Galaxy Open bow with the upgraded 7.4L Bravo one. I love this way to winterize. Your video is awesome, yes short but a no brainer. BTW, very nice boat you have. Dan in Utah.😊

are the bolt reverse thread? It looks like youre spinning them Left???

How would you dewinterize? I have a 33’ SD cruiser with a bathroom. I know it’s a few extra steps for the sinks and toilet.

To heavy to race

!!!

Came across this video. I believe I followed everything you said but my temp went up to 180 degrees and I panicked and shut it down worried I burned up my impeller. Does the engine get hot because it’s being starved of forced water from the garden hose?

Everything

9:36 humans make mistakes

What a race

Just got home and I’m not going to bed yet so I’ll talk with him later and I’ll talk with her about that thank the universe is so sweet to see him

What is the name we are doing now I don’t think I will. Compton royale doing Ronaldo how to start on Fruitville

Dude tripping in the beginning probably thinking shit that's definitely going on KZfaq lol

What atv are you riding?

Hey Ken! Thanks for the tip! I heading to get some jugs to rig me up a system tomorrow. You don’t even have to drain the block or exhaust manifolds this way just be done with it! I have the new Bravo outdrive with low water pickup and a special nose cone adapter for it. I hope it suck hard enough to bring that antifreeze up into the engine?! I always wondered how those impellers sucked with no pressure just gravity drain like your doing? Obviously it works for you!! I just spent $22k on a new rebuild so I’m nervous this year and late!!! Have about a week!

Driving 10/10 Driving whilst making sure camera lense is clean 11/10 great job!

awesome

your changing them why?? what rust,, ??

that was a crazy race thanks for sharing it. 👍

man race keeping the camera clean .NICE JOB 🤘🤘🤘

Thanks for the video! I noticed a small leak around the gasket of the risers on my 1996 aquaton 2350(kind of rare boat) with 350 Mag when i ran it on the hose to get it ready for summer. I have pretty much the same set up but i have hoses connecting to my risers where it looks like yours are capped off. I found the the leak was coming from the hose. But since i pulled the riser off the gasket was falling apart anyway so i will replace them. Im in Ohio too. Do you ever take your boat to Alum creek at all?

I would really like to ride those trails!

Respect for racing and trying your best to keep the lens clean. Thanks for this content man! It’s badass!

Great video...I'm doing my risers on my 454 340hp MEI's soon, and this was very helpful!

This will be my first year racing and racing here. I appreciate the video helped me learn alot especially if the trail is the same for this year 😅

If you have closed loop cooling is this still required? For the exhaust yes bc that's water cooled. Thanks

Hi this is Joseph Kitts

That’s how I do my 4.3L everyone tells me you need need to drain ur block in between the water and antifreeze. No the antifreeze displaces the water as it pumps through. I run 5gallons through mine and fog it so it acts like it wants to kill then when it smokes spray fogging oil till it dies. I do pull the hoses off each side of the water pump after and dump a gallon down each side to be sure. Prob over kill

This is the way I have done it for ever. Just needed to see someone else does this way also. Great vid short sweet and simple, thank you

Think about how hot that bike is 😳

Do you prefer using oil over fogging spray?

Are you in 4x4 the whole time? I went in 19 and 21 as a spectator. Great to see what the course looks like. Nice riding.

Hit the gas and never use brakes

good job ken, "10 seconds"

Go fast and pass every racers

J

Million dollar idea 💡 GoPro tear offs

Jeeze is it just me or is this dude holding back?

Nice video! At the very end you said put your out drives out or something close to that…. What does that mean? How long have you been doing it like that and what part of the country are you at? Thanks

Nice

He looks like he is tightening counterclockwise and loosening clockwise. Whyn is this?

Motoslitte elaborate

Ooohhhh man!!! He ate fuck!!lol

😁😁😁👌👌👌👌

Hello form Romania Nice track 👍

What kinds of forwheelers are those

I have the same engine in a 93 Formula. Great video btw, I’m currently not getting water flow out the port side “ behind captains chair, I may have my sides mixed up” through hull exhaust. I often wondered how much water falls down into the stock stern exhaust and doesn’t make it through the captions call mechanism? I’m going to dig into this issue but wanted some feedback back on if this is common and where to start looking as far as why I’m not getting good water circulation out the port exhaust? Starboard side looks to have decent water flow out the through hull exhaust. Btw currently not having an over heating issue. Also experiencing some new electric issue that is effecting the firing but thats another topic if anyone is skilled in this area I’m all ears. Thanks

I know how to replace them, but just wanted to see if someone else used gasket cement. I can't tell if the old ones had cement on them or not from the last person who changed them. Guess I won't use any. (Note: the first camera was oriented correctly, but the second one was a reversed image) [ I wondered why all the accessories were backwards of my 454, and unscrewing the bolts in a clockwise direction ]

I was so invested in the race. I was leaning left and right and almost fell out of my bed lol

❤❤❤❤❤