Жыл бұрын
Пікірлер
@rayanr3627 22 күн бұрын
what brush kit did you use ? is there any original Denso brushes for toyota starters ?
@barajasautodiagnostico9925 Ай бұрын
amigo que tipo de pintura usas para pintar el housing y la tapa,?
@lennybruce6635 Ай бұрын
I'll go some where else now the noise in the background and that loud annoying fing music!
@lennybruce6635 Ай бұрын
Shut the music off so I could hear what the hell you're saying!
@marcioelivelton5274 Ай бұрын
Caramba mano, porque não usou o rolamento velho para bater em cima do NOVO????
@takeshi1242 Ай бұрын
Nice, giving life to an old component instead of just tossing it away!
@j.jarvis7460 2 ай бұрын
My work came to a halt right when I discovered I needed a 17mm hex socket for the pulley bolt. Every store seemed to stop at 16mm
@barajasautodiagnostico9925 2 ай бұрын
carnal. es muy bien tus videos, haz mas de otros alternadores y arranques. animo
@barajasautodiagnostico9925 2 ай бұрын
amigo que liquido usas para lavar las partes, la maquina donde los pones es de vapor?
@barajasautodiagnostico9925 2 ай бұрын
hi bro, what liquid to use for parts clean?
@laughuntilyoucryordie 2 ай бұрын
You might want to touch up all that silver paint that got scratched and dirty before bagging it up to sell! 😮
@laughuntilyoucryordie 2 ай бұрын
Wait a minute…let me get my blurry glasses 🤓 on so I can see what you did when the video got blurry 😂
@laughuntilyoucryordie 2 ай бұрын
Ok…they make a TOOL for that lol 😂 to remove that bearing retainer clip!
@ShakirAuto067 2 ай бұрын
Good working bro 😊
@silentbravo 4 ай бұрын
Nice video, nothing mentioned about brush wear or busing wear though. Could do without the music too, it's just distracting.
@Kyle-ev4fk 5 ай бұрын
Thank you, this is one of the better videos
@harbinn111 5 ай бұрын
Good job can you show me the wiring charge(wiring) you made on you garage with light and batery tester thankyou
@ShakirAuto067 2 ай бұрын
Good bro 😊
@stevea6722 5 ай бұрын
Don't hammer on the inner race of the bearing, unless it is a press fit on the shaft and then only with support. Front bearing install, use a driver that contacts the outer race only!
@ShakirAuto067 2 ай бұрын
Nice bro 😊
@salmansaeed7660 5 ай бұрын
Please give me job
@MrOnemanop 6 ай бұрын
Obviously not his first go around.
@reynielasencio1964 6 ай бұрын
Jesús. I didn't knew that Nayib Bukele was rebuilding starters on his free time 😂😂😂. Just joking my friend. Cool video 👍
@affordrentcar5021 7 ай бұрын
can you please give me the link to buy tool for this Alternator Pulley Removal.
@sd906238 4 ай бұрын
Probably a 17mm allen head impact socket. Use it to only remove the decoupler pulley, don't use it to install the decoupler pulley.
@jimmccune568 8 ай бұрын
Wow.
@ShakirAuto067 2 ай бұрын
Nice 😊
@Danny190 8 ай бұрын
Good stuff man!! Where could I get parts for newer starters and alternators for like an example a 2020 GM truck? Also a tutorial video on that would be great!
@sammaleki110 8 ай бұрын
Thanks for video it’s very helpful, what’s the size of the bearings
@jasonemalin 8 ай бұрын
Is there a reason you repacked the bearing instead of replacing it? I think that is likely my issue I have. I'm getting a chirp and I'm pretty sure it's the small bearing, but won't know until I take it apart. Thanks for any insight you might provide.
@Auto209 7 ай бұрын
Probably because theyre usually fine as long as they have grease and weren't already messed up. Not sure tho I'm just giving my opinion
@allensooter8429 8 ай бұрын
Crude at best.
@valuedcustomer9614 Жыл бұрын
00:30 It's a mistake to hammer the bearing into the housing by striking the the inner bearing race. This will damage the bearing and reduce its life. A bearing should be pressed into a housing using a pipe or socket on the outer bearing race.
@guglegugle8075 9 ай бұрын
On to ma w dupie. On robi alternatory dla pieniędzy więc ma w dupie czy On będzie długo działał w nie jego samochodzie 👌🐏🐑🐏🐑🦄👌🫶😉🦄🐏🐑
@RCAutoElectric Ай бұрын
Thank you for noticing. Our intention was that for ordinary DIY people with no specialized equipment can get done. Even if you don't have a press you can still achieve acceptable results.
@09JSanchez Жыл бұрын
Great video. Are the long bolts supposed to clamp it shut to a specific distance? I opened my Bosch alternator to clean it then it's kind of loose on the mount. I'm afraid I may have clamped it a little too far. I had replaced the bearings on a previous ocasion. I never removed that plate that gets soldered on top. It was very interesting seeing that in this video.
@quicksilverguy21 Жыл бұрын
Great video! I’d love to see how to take it apart as well
@RCAutoElectric Жыл бұрын
Thank you! yes we have the Part 1 of this rebuild as well, here is the link kzfaq.info/get/bejne/pKuXYNF8tciznp8.html
@emmanueladalikwu3328 Жыл бұрын
why is it giving out 14 v instead of 12v please
@RCAutoElectric Жыл бұрын
The way the charging system works on this vehicle, is the battery is at 12 volts, the alternator, brings up the voltage from anywhere from 13.5 to 14.5 in order to charge the battery while the car is running and and to supply adequate charge all the electrical components in the vehicle.
@rigarcia123 Жыл бұрын
Muito bom mas com o preço das peças e da mão de obra fica bem mais barato que trocar por um novo? Poderia apresentar uma lista dos custos? Onde fica sua loja? Funciona a base de troca? Quanto sairia este do Toyota? Obrigado
@RCAutoElectric Жыл бұрын
Hola hermano, todo la informacion esta en la descripcion. Depende cual cua es el model y el ano. Nuestro website casi esta listo. Busca un caro en particular?