Spot on and easily understandable to a caveman like myself 👏🏼

Hallo, wo finde ich die deutsche Version?

so happy to find your fideo thanks men.please continu

be good if you would show a before and after print so we know if this is all just a waist of time

Your voice is amazing!! Have you recorded any audiobooks? If so I would love to listen to them!

The Artillery is total rubbish.

I followed this but I encountered a BL Touch error M999. Do you have a fix for this?

I had noticed the pinion gear being off centre on two of mine but I need to check the rest lol and those original ptfe tubes are useless.

Zuca, by those who don't

if only pointer adjustment is needed….just remove the bezel and glass…remove the pointer and replace in the corrected desired position…replace bezel and glass…job done..

stl ?????

GREAT, GREAT VIDEO! Thanks so much for this, i've been printing like crazy for 4 years and never really understood coasting and wiping! thanks, now I do! Subscribed and Liked :)

you English is great! but if your going to talk english please put cura in english too ! great vid thumbs up and sub

I usually turn combing off completely

Really well explained! Cheers mate!

Thank you for this. super helpfull!

I have to hand it to you, an outstanding and not too long or covercomplicated explanation! Just a tiny issue w/ the german language in cura but we can figure out ;) Keep it going and enjoying the amazing hobby!

Is this tutorial still valid? any new better parts/software that is avaiable?

Thank you for the video. I've learned a lot from it.

Amazing. The knowledge that you are sharing is way more than just the typical “The Perfect Cura Profile” videos most make. I love that you were actually speaking about the physical aspect of nozzle travel when printing, and the nuances or issues involved. Your English is amazing, and you were very effective and describing the nuances and how to handle them.

Awesome! Thank you for explaining it very well.

Best part is you can use a 0,25mm nozzle and have extreme quality but still use 0.5mm line width to increase speed.

Nice, but I've also noticed that the filament climbs back and forward on the teeth on the big gear, changing the quantity of filament being extruded. Extruder works more consistently if the bearing on the idler arm is also grooved keeping the filament on the teeth at the same diameter. My Genius Pro has extremely bad horizontal banding and was suffering all of the faults you have shown here, plus more. It still prints with banding and I am trying to determine exactly where it is originating from. Maybe the Z axis gear.

Amazingly helpful video!

This video helped me put my printer back together for the second time, so thanks for all your help.

Very helpful. Thank you

Great explanation of coasting and wiping👍🏽

🎉

The BBs in the wheel can be used to replace the ones in the Nema 17s.

Your English is excellent, really like this video Please produce more

Hi friend, this firmware is possible to use the M600 code to print color. Nice explanation tanks.

I would really like to see a description of the the different coasting settings and how they effect the seam. I have played with every setting and I struggle see the difference any setting makes.

This video helped a lot. Thank you

Keep it up. You explain things well. Thank you

That was a VERY GOOD explanation! Danke!

The link to the Thingiverse is not working, can you share it please?

Thank you for the tips and showing the driver anatomy. ‏‪3:26‬‏ I'm still not sure about air gap effects, but heaving the ptfe coming too much causes in my printer to it being crushed, narrowing the ptfe tube at the end of it and blocking pathway of filament. So I'm still not sure about the correct ptfe placement. I guess it should be exactly straight with the exit - avoiding air gap, and on the other hand, avoiding the nozzle to squeeze it. Thanks for documenting this.

The link to the Thingiverse parts is invalid.

I have often wondered if it would be much easier to adjust a dial caliper if the actual rack was made to move back and forth.......then all you have to do is slacken the holding screws for the rack and move it left or right to get the needle to once more be vertical.......this would save having to open up the works to get it to calibrate to zero........my Mitutoyo dial caliper has a single small gear that meshes with the rack and it sometimes hops over a tooth and the needle goes off centre......crap design.

Primero agradecerte el esfuerzo que compartes con todos nosotros,gracias. Tengo un problema, he flasheado tal y como indicas en el video pero la impresión se para y no aparece ningún mensaje, que puede ocurrir?. Gracias

Pretty! Can you give insight in how to eliminate the distortion between bottom layer and first few layers? I run into the same problem!

"the extruder cannot be the cause" - Don't be so quick to discount dual extruders causing resonance. This is a thing people have had to trouble shoot. Chep did a test where he tested a 0.9 motor and it made no difference in quality at all. This is the thing with 3D printers, what might work for someone doesn't work for someone else, or the upgrade exposes other problems. When you work with such precision and want the best you can go down a rabbit hole very quickly.

Link del dispador de auminio, porfa

If the TFT FW Update doesn't work for you, try formatting your SD card as FAT, and not FAT32 or anything else. Worked for me.

Love it when the pen comes out and the path of the wipe distance is thoroughly explained. This kind of technical information is very valuable.

Excellent stuff, thanks for sharing your knowledge.

Excellent video, which I've now bookmarked in my "WTF is going on with my print and how can I improve it?" folder. Vielen Dank!

Thank you so much. I fix a lot of the tools that we use and make some custom tools that are part-specific. This will hopefully help me fix the collection of dial calipers that are in my repair bin. I'm looking for the preset torque specs for the main test indicator tip pivot for jeweled bearings. They seem to be extremely delicate and sensitive. I'm not sure that my old hands can feel that tiny amount anymore. Thanks again for putting this up! It is also great to get this from someone with the same perspective, being German/Austrian myself. We seem to have a knack for inventing tools and machines. We see things from an "analytical and How mechanical things work" perspective. It makes us good at what we do. I work in aerospace, and due to a spine injury, no longer operate large cnc milling machines. I assemble subassemblies and rework and repair parts that need some help. I have to know a whole bunch of stuff and have had to come up with new ways to do things when the common methods our vendors use fail. Parts get scratched, dropped, banged, and dented. They complain about how many tools I have at work and that three tool rollaway cabinets are too many , but I can do anything they throw at me. I have been meaning to look this up for years now and just got it in my head tonight. Thank you!

Thank you for explaining this! I’ve been struggling with the z seam for quite a while. Even after watching this, Im still having issues. Would it be possible to email you and show you my settings?

What version of Cura are you using?