Hiya, Great video and very informative, thank you. Very interested in the 55mm middle shock, would appreciate your link to the fitting process. Thanks.

Can it charge 4s at 12amp

Hope all is good, would love to see some new projects on the channel. Take care, cheers!

Great list. Loved it. What about adding the upper deck (not in stock kit)? What about aluminum motor mount will it noticeably reduce heat?

This is a cool study of your improvement.

Cool video!

Hey, does anyone know why my 3.0 bullet starts running away just after l start the engine?

Some people should never become musicians

Excellent video Sir 😎👍🏻

hola buenas tiene marcha atras o solo es el gatillo acelerador y freno

Hi, do you know which m05 kit comes with hex screws from factory? Thx

Did you use 55mm chocks on all 4 corners?

Helped great, was hoping I wouldn't have to remove the engine but everything ls a tight squeeze, just waiting on my roto start arriving but thanks

Have you ever adjusted the motor by loosing the screws and adjusting timing to improve power?

Knock.!! Knock.!! Who's there.? Orange.! Orange who.? Orange you glad they do aluminium upgrades.!?! 😉 😉

Hello can I ask what wheel to use as got all alloy parts bottom arms steering the lot but wheel keep distroying wheel hups and tyres help would be great you vids are great.

Nice review. What is the wheelbase?

Hi mate, can you do a follow up on this video please, and we would like to see how you mounted the exhaust! cheer

Every video I watch for the m05/m06 builds they still lube the shafts the counter gear, spur gear ride on and the axles. Why? Wouldnt that lubrication only be needed if you are running the plastic bushings? If you are running bearings that lube is NOT necessary!

Where did you find the roof rack?

' try use a rear drive and neutral a front wheel

I’m about to start a similar project How’d it turn out? Do you have a finished video?

Awesome video! I was wondering how to remove that so I could change my drive shafts!! Thanks for posting 🤙🏼

I personally would've shot this video again due to the camera focus issue. Good information, but hard to watch, hard to know what you're using. But thanks anyways.

Try this: First: soak at approx 40 C (no warmer than 48 C), a solution of citric acid (5% by weight) and dish detergent (another 5%) with water (the balance). Soak for 6 to 24 hrs, no less and no longer. Second: rinse then soak in filtered tap water (no warmer than 22 C) for 1-2 hours. Use clean glass or plastic containers. Once out of the rinse, dry immediately and thoroughly. Use compressed air or an air duster if you have it. Lubricate as normal, but don’t use WD-40 at any stage. The citric acid will eat (actually dissolve and convert) the rust without really eating the metal at all (it’s extremely weak), and the dish detergent will both act as a surfactant to help the citric acid get into tiny places and also grab and trap any dirt and oils. Don’t use baking soda or anything, it may have a type of crappy mineral plating effect. Same with hard water. In this application, you don’t need to neutralise this acid, just dilute it. Citric acid you can just use the supermarket one, it’s fine. The iron oxide (rust) will convert to iron citrate which is water soluble. It will just wash away with the detergent.

Where did you get that purple car stand ?

I really need help with building my lunchbox, i just cannot get my head round how axel springs are meant to to be fitted.

What length of shock did you use?

Nice video. These tyres looks so wide, what is the product code of Tamiya?

I agree with all, just go for the tamiya plastic hop hups instead of alu, spare (if u found them cheap) money and the car will weight less!

What's the offset off those wheels

Great video mate. What chassis would you recommend to just stick the wheels and body on with minimum effort!! You said you had a chassis did it fit?

Where do you buy the new parts from ?

En fracais svp putin

Thank you 😊

What are the dogbones like for falling out

Since you want to charge the battery easily, and you don’t give a shit about your receiver or being waterproof, here it what you should have done. Put a small LiFe battery in the battery box. Modify the box so that the balance lead is exposed from the box on the top. Now you can charge your battery from the balance lead without removing it. You have a lithium battery which is strong, no sag, long runtime, don’t need to access. And it’s only 6.6 volt so the servos won’t scream

Cold plug is for hot weather ,and harder to tune engine running colder plugs

Stumbling back to this channel after 4 years… God I miss those days! Nostalgic watching back on some of these videos! Would love to see your return!

Thanks for this video series - just bought the same model and as a complete novice in all things RC these videos are going to be bloody helpful!

this video was a great help thank you

Looks like Old Mill Creek

checking back in. hope everything is good. still awaiting the return

Looks dope

Very nice testing!!! Appreciated!! 👍

👍🏻

Awsum van.

That's a really good price for a transmitter of that caliber

Starting my first FWD RC kit and also a mini being 210mm wheelbase. Great series thanks for the simple easy to follow content.

What do you call that thing that goes up the body the bla k thing please answer I wanna buy one