Thank you for taking the time to show all the awesome people what's going on!! !!
@enrikuar6324Күн бұрын
What's the point??? Waste of time!
@Daddyblacky956Күн бұрын
i have a WS2200 model bought it in 2019. Same thing happened to it. Wow!
@elriendo3 күн бұрын
Thank I have that problem
@fishboat62446 күн бұрын
Old post but I'll ask anyway. Do you know if the YG2800i has a cylinder that can be honed? I was given one with low compression, I want to put new rings in it but I want to make sure the cylinder isn't chrome lined or something . Thanks
@ZombieDaveAZ6 күн бұрын
@@fishboat6244 not chromed to my recollection. It was a while ago though.
@Teambadecision7 күн бұрын
You think you could help me diagnose my pole saw it’s the same one. Please?
@ZombieDaveAZ7 күн бұрын
@@Teambadecision I'll do my best for you. Tell me what's up?
@Slim14237 күн бұрын
Hi. Have a question. Got a older 550 series B&S engine. Been a good engine up until lately. A short while back it started burning more oil first a little but now a lot, running slower and then normal and visce versa, the spark plug is frequently getting clogged with oil or carbon, lots of white smoke coming out, one time the engine wouldn't turn but i got it going again. Leaking oil around breather assembly. My question is it worth fixing or will the engine need a overhaul? Do i have a bad breather assembly or do i have a blown head gasket, or possibly both? Need your advice badly.
@ZombieDaveAZ7 күн бұрын
@@Slim1423 Good morning slim. Let's just go thru this and make sure we haven't overlooked anything first. Is the oil at the proper level? Should only be about 18oz. Is the air filter in good shape? How is the mower stored when not in use? Flat on the ground? Got any pics that may be helpful to me?
@Slim14237 күн бұрын
@ZombieDaveAZ Yeah, the oil was at the proper level. It use to only use 2 to 4 ozs oil on a yard, but yesterday i was going through about 8 ozs, every time i filled up the gas tank! White smoke was blowing out the muffler, the spark plugs kept getting clogged up. Lastly, it cut off and i couldn't crank the engine up anymore. So, i may be at an end with my mower. Mower sits on my porch, with a cover over engine. I use pennzoil SAE 30, and i try to keep engine oil topped off. Oil leaking around the breather assembly. I use gas either fresh gas or gas mixed with fuel stylabilizer if keep for a while.
@mitchellcrager99337 күн бұрын
Trying this later!! I have pulled and adjusted the carb till I'm ready to throw the stupid thing.
@oliviafranks8 күн бұрын
mines not starting even when i spray starting fluid, do you know what it is
@ZombieDaveAZ8 күн бұрын
@@oliviafranks did you check for spark yet?
@phylliswhite41548 күн бұрын
Ethanol has water in suspension since it is not refined to maximun of 196 proof but instead to only about 130 proof . After it sets for an extended time separation can occur. hence since water is heavier than alcohol or gasoline it collects at the bottom of the tank and is the first to be drawn into the carb essentially drowning the engine. Do not use ethanol blend gasoline if possible. If you do be sure to draiin it from the system before storage. or add a fuel stabilizer. Shake the saw to remix the fuel in the tank after storage before starting.
@AntwanThompson-b9s12 күн бұрын
❤
@ZombieDaveAZ12 күн бұрын
Appreciated 👍
@blabzasspace24613 күн бұрын
Thank you for this video it help lods
@paulpeaked728614 күн бұрын
Ok so when u say rewired the fuel pump , which ones ? Is it the connector harness to the fuel pump? Or those open solder connectors on the fuel sending unit . Thanks in advance
@ZombieDaveAZ14 күн бұрын
@@paulpeaked7286 connector harness.
@paulpeaked728614 күн бұрын
@@ZombieDaveAZconnector harness to fuel pump , on the outside of unit or inside
@ZombieDaveAZ14 күн бұрын
@@paulpeaked7286 inside from the top of the assembly at the canon plug down to the pump. I cut and soldered in the wiring for the new pump
@HowardNichols-g6q14 күн бұрын
I will be installing a Hyway cylinder and piston
@daveb196314 күн бұрын
Bs...
@HowardNichols-g6q14 күн бұрын
The JB Weld Extreme Heat held up for running with no load. When I started cutting a large log, the JB Weld failed.
@ZombieDaveAZ14 күн бұрын
@@HowardNichols-g6q I noticed that when I order replacement cylinders (aftermarket) for cut saws they don't incorporate that bonded port plate. Just worth noting. Do you think you will replace the top end?
@toddyuill392415 күн бұрын
I found my relay on my 99 it was buried up behind the fuse box in the driver's foot well I stuck my hand up there while it was running the relay was so hot it almost bunt my hand replaced it it was all rusty inside runs like a champ now
@mackendw18 күн бұрын
put a new carb (chinesium) on my poulin p3314 saw. it will start fine when cold no issue. run for a bit, shut it off and it is a BEOTCH to get going again. I did the mod you noted to the cover drilling holes in the plastic cover. plug has good spark...is getting fuel. there is great compression. new fuel mixed correctly. ideas??
@ZombieDaveAZ18 күн бұрын
Did you do the choke out and then 1/2 way back in? That helps a lot. That's the high idle restart.. also clean air filter.
@mackendw17 күн бұрын
@@ZombieDaveAZ I thought using the choke only applied when the saw was cold? new clean air filter installed. new fuel. (40:1). I adjusted the coil pickup so it was closer to the 2 pick ups on the flywheel. seems a bit better now.
@mackendw16 күн бұрын
@@ZombieDaveAZ I put new fuel lines and primer bulb in it. that made a big difference. it was leaking fuel under the carb and sucking air I guess. starts right now.
@HowardNichols-g6q18 күн бұрын
I had the same problem with the cylinder side wall cover. Stihl's only response to me was that my warranty had expired. I pulled the cylinder and reset the cover with JB Weld Extreme Heat. Got it reinstalled and the saw is working
@HowardNichols-g6q18 күн бұрын
I had the same problem with the cylinder side cover. Stihl's only response is that my warranty had expired. I used JB Weld Extreme Heat and put it back together and the saw is working
@jimwyant850919 күн бұрын
any tips on getting out the emulsion tube when they are stuck in the carburator?
@ZombieDaveAZ18 күн бұрын
Jim, first I would research if a NEW carburetor is available to you and if that's a viable option. If you locate one, just know that worst case scenario is that will have to buy it if things go wrong. I have had some stubborn E tubes in the past. Generally a good amount of WD40 and pushing down with a flat screwdriver will get it loose. You may also need a small Allen wrench to help it out the last little bit. The angle on the Allen wrench is what does it. For a good visual there is a gentleman on KZfaq "Bruce's shop". He does a lot of these carburetors and is very good at it. I hope it helps you out.
@kebo5720 күн бұрын
I think PP is polypropylene.
@paulpeaked728620 күн бұрын
Circuit opening relay is under dash to the left , u pointed it out already .
@ZombieDaveAZ20 күн бұрын
@@paulpeaked7286 you would think that it would be marked inside a cover or someplace obvious. I appreciate your input brother.
@user-dk8oe8cd2u23 күн бұрын
Great video TY
@ZombieDaveAZ22 күн бұрын
@@user-dk8oe8cd2u thank you. 😁🍺👍
@jason-white23 күн бұрын
Yeh, I'm using a tip cleaner,
@ZombieDaveAZ23 күн бұрын
I know some guys that use those little micro drills too.
@jason-white23 күн бұрын
@@ZombieDaveAZyeh, I saw one that used a micro end mill
@atomicsnowflake213025 күн бұрын
Thanks :)
@garywarford610327 күн бұрын
I’ve done everything you did to yours and mine still won’t start is the something in the security system that could disable the fuel pump
@ZombieDaveAZ27 күн бұрын
Hey Gary, that's a good question. When I read it I tried to do a little sleuthing on the subject. If it was a security issue (from what I'm reading) it would show a hard code that could be read from an OBDII scanner. Perhaps and this is just a guess but perhaps a super high dollar scan tool could reset that code. That would be the way to go I think. If it's a "hard" code, disconnecting the battery would not erase it. So basically I am no help to you on this. Perhaps a 4runner forum would help you to narrow this down. Best of luck my friend. 🤔
@stevenvelasquez198828 күн бұрын
What type of Orange spray paint did you use.
@ZombieDaveAZ28 күн бұрын
Hey, Steven. I'm not sure what brand it was. I only cared about the color match. I took a pic of the cleanest spot and then color matched my pic with the lid on the spray can. I did get it at Walmart, I can tell you that much.
@BeADad2447Ай бұрын
Anybody know what was wrong? I just cant listen to all the drama.
@ZombieDaveAZАй бұрын
To anyone reading my reply comment to this guy BeADad. Do NOT Tell him anything!!!! Here's why. I spent HOURS trying to solve this particular problem. You don't have to subscribe to my channel, I don't monetize. It's MY findings being shared in order to help others. This guy has the balls to ask one of you to share what you learned by watching the video because he can't take the time. This is a huge problem for tik Tok scrollers. If you don't catch their attention in 10 seconds they move on. Lol 😂 Now, because I didn't like the the way he phrased his comment and if you guys support me he will be FORCED to watch the video. Then maybe he will solve his car problem or maybe he won't. I personally don't give a F--K! This is the epitome of someone trying to look over your shoulder to get the answers during a test. You did all the work and this clown just wants the answers! That's BullSh!t!! Whew I feel better. Now let's see what this keyboard warrior has to say. I'm sure it will be a winner. Educate yourself and be a better person. Don't help this guy. I actually do feel better. 😁
@kraftzionАй бұрын
I got a 4218 that I have modified everything on. Nothing left but the ring on the filter cover, bored the carb venturi out from 9.5mm to 12mm and shaved the butterfly shafts and screws, ported,muffler modded, ignition timing advance, opened the hole up from the fan to the carb section, ground all the safety rakers off the chain etc. Went from 14 seconds to 7 seconds on the same log. What has remained consistent is it won't hot restart unless you pull the trigger. Pull the trigger and it hot restarts 1st pull every time. So if you have one and nothing else works try that. Come to think of it, setting it back to fast idle might also work. I haven't tried it or even thought about it until now, found a solution that worked and didn't pursue it further.
@ZombieDaveAZАй бұрын
It sounds like you have a helluva saw! Yes, for hot starts and just general operations it's always best just to read the owners manual. For restarts : pull the choke all the way out and then halfway back in. That sets the high idle. Good luck with your modded saw. 👍🍺
@kraftzionАй бұрын
@@ZombieDaveAZ Yea it is 2010 saw I bought a couple of months ago for $20, no owners manual included. I'll try that next time. It didn't occur to me as all my other saws hot restart without a problem. Thanks!
@StickerstackerАй бұрын
Thanks! My back pack blower just all the sudden wouldn’t start and had a wet filter.
@MadGittyАй бұрын
What if the blades broken off
@ZombieDaveAZАй бұрын
Is this on a push mower or riding tractor?
@HecFCovPeАй бұрын
Thank you sir, i had the exact same problem! 😅
@NeinFelineАй бұрын
Used it today! Needed the part about where the internal spring notch catches on the notch oart of the housing assembly... Then learned I can't turn more than 7 times without it popping off... Got everything assembled with the pull cord replaced with diamond cord kit and VOILA! Started right up! Bless You Brother 🙏👍
@ZombieDaveAZАй бұрын
@@NeinFeline so glad it worked out for you. Happy mowing🥴
@royhennagir7685Ай бұрын
Thank you!
@raycharles704Ай бұрын
I have to do this soon im trying to find someone to help cause i don't have $2000-$3,500 to pay anyone in labor 😂and i have no tools
@josedejesus6185Ай бұрын
Nice, very nice discovery and advice! Keep it up!
@ZombieDaveAZАй бұрын
Thank you friend.👍
@Doc-Cole_Trickle-of-ChainsawsАй бұрын
👍🆙ZD
@steveriggenbach90Ай бұрын
One of the reasons I have watching for so long……Your thought processes.
@carloslima439Ай бұрын
Spark resistor
@ZombieDaveAZАй бұрын
kzfaq.info/get/bejne/fpdln5mKsZjUoI0.htmlsi=uwLyE0rKPp59Ld3d. Follow this link to view the original video. I hope you like it .
@philipcarlson7416Ай бұрын
Good job finding the problem keep up the good work
@ZombieDaveAZАй бұрын
Thank you Philip. I appreciate the kind words. Have a great day.👍
@steveriggenbach90Ай бұрын
Lost your contact so….Happy Father’s Day
@ZombieDaveAZАй бұрын
Thanks buddy, I hope you have a great day as well.
@leonseyer7884Ай бұрын
hey do you know if you can change the accelerator position from hip to tube? on the 9010.
@ZombieDaveAZАй бұрын
You sure can change it to tube throttle and no special pieces or parts needed. Find the tube throttle on Amazon or from the dealer (much more expensive) and you're in like Flint. Should be about $50. Good luck. 👍
@MikeNBikesАй бұрын
I wish you didn't zoom 500x to where you cant see shit
@ifranksultanАй бұрын
I love you bro. Just saved me 200 bucks. I had the same problem. Fixed it in 15 mins
@ZombieDaveAZАй бұрын
Happy to help brother. 🍺👍
@ColinHenderson-qn3dmАй бұрын
I just tightened nut and used a long breaker bar on it and it popped into place
@justincarmello8493Ай бұрын
Beautiful video
@jefferyfunk35982 ай бұрын
Get rid of the potato camera. 😅
@Aviator3812 ай бұрын
I have this blower it was 2 years old I’m still trying today it’s been a month of trying nothing yet but wish me luck
@ZombieDaveAZ2 ай бұрын
If worse comes to worse email me at [email protected] then we can exchange phone numbers and I'll talk you through getting it running. 👍