Thanks mate helped a lot

30 minutes or more and only a few p. Just bring it in as irony and scrap the whole thing if they let you... Some do some don't

I have a 009l wating on parts to the same thing thanks so much

Great work 👏 👍, no loud music no weird tricks, straight to the point well explained with no words .

Great video! Can anyone tell me the easiest way to change the belt on an Admiral? Clearly I have to pull about the roller assembly to a degree - how do I go about this? Thanks in anticipation :)

So I put the reapeter where I want the connection to be extended?

Thanks 👌👌

Thanks for sharing - this helped rule out coils as my issue and it ended up being the coil gap itself on the one side, set to Briggs spec of .010 and now Mower is running like a champ!

How to recharge

I need it with simcard

Is there any difference between testing an electronic ignition coil and an old-style points ignition coil?

great vid, suscribed, lovely, will watch more

RU afraid to demo your catcher repaired job by starting your mower on KZfaq?? I don't have confidence in this repair job! There's "NEVER enough time to do things RIGHT but always enough time to do it AGAIN!!!

Why not place the patch on the "inside" of the catcher material; that's the side with air-pressure and grass-weight pressing on it?? Outside patches have a greater tendency to get blown or knocked off. Also, patches are best when they have rounded edges, not corners <= corners small size have the tendency of lifting-off?

Can u please help. When we put the address in by google it doesnt take us to the log in for us to put the details in

Thanks for putting this video up. It doesn't help me, as Camec chose to put a steel wire strap on the inside that is tightened with a loose nut/bolt arrangement that precludes just pulling it off. Bloody annoying. But your video has obviously helped others, so thanks for doing it.

Thank you for these clearing instructions, it really helped :)

For me it doesnt show up on available networks

Testing the kill sith both ways should read differently. One way the 2.6700 ohms and the other way shouild read "open."

didnt work for me unfortunately

coud not even log into the IP useless the page can not be reached also does not recognise my router

have a briggs sprint 40 lx from 2000 and this is the first time it's not sparked, now know the coil is ok and it's probably the 24 year old plug, thanks Roy.

great tip , thank you

EXELENTE,el video me fue muy útil, ese tipo de Arrancador no es tan común, Muchas gracias por el video

I have a old briggs and stratton mines coming up as 12.66 not sure if im doing it right

Thank you a repeater is not what I thought it was, you made it clear.

🐐

At 4:38 you should have said "infinite resistance" No resistance is continuity which would read zero.

Very good 👍

Thanks Mate

I do like that little tip of the Emery paper wrapped round the feeler gauge, very good 👍

Great video thanks. Helped me out. But where can I find the gasket and metal plate? I don't have those on mine.

Great video ...I've just got my mower working again thanks to your tutorial. however, I think I'll need to replace the gaskets in the Carb the next time around the 'o' ring was flattened and I'm sure the gasket was missing from the carb end that meets the main engine. can you suggest where I can get the carb kit for mine. It's a Mountfield SP534 model 51cm cut. Cheers

When cleaning our Indesit washing machine, the inner tension spring ring came loose. We were about to buy a new machine until we came across your video. Competent instructions, easy and successful to follow, many thanks from Austria! You, Sir, are a hero to us!

These also fail when they warm up and leak internally due to insulation failure. No test for that.

you are lucky you get a fuel tap built into the tank. Over here it is just a fuel tank , no fuel tap.

Help me mine was i accidentally upload a picture on software upload after that it never show the wifi ssid and stop blinking at i can't reset any more

Cant get it working using LAN...sucks to be me lol

Sorry for last comment,mine had already been pulled apart & 2nd spring was missing,have a great day Roy.😊

You said the spring was in wrong hole,why did you put it back the same as it was?You made it sound like there's 2 springs when there is only one.

My Briggs coil is showing 6.2 is it still good?

Hi Roy, I have atco lawn mower, Very old battery turns it over and over but it doesn't fire up? When I star it by pulling the cord it starts straight away, Please suggest, Much appreciated.

Ok so I plugged it in via ethernet cable all the lights came on but still no better? I tried the ip address but that doesn’t seem to work either? Any ideas

MY coil is reading 2.6- 2.7 is that okay?

Thank you

Hi Roy ,I think I should point out that the 3rd coil you checked as open circuit has the metal cased.Resistive plug connector which plugs into the coil lead .It's value is 5k ohm. If this item is open circuit or the connection is corroded to the lead.Then the test will show no reading on the coil.It can be misleading.I got caught out and purchased a new coil for nothing.Cleaned the connection after finding out it can be separated. Then tested ok.

8:40pm 1/5/24

I spotted an essential piece missing as you put the blade on and thought at the time “this fellas missed a part” 😂 I’ve just inherited one of these myself, used it today for the first time. The only issue I have is the fact that the blade spins permanently whilst the engine is running instead of only spinning when engaged via the handle like a lot of my previous mowers. Not sure if this is standard on this mower or if it’s something I need to take a look at. Great video mate 👍🏼

Well done sir . Thank you.

Hard to find that cable. Any ideas? Great vid btw.