SFMF!

Empty 9mm shell case might work?

Spring is dragging by the looks of it

This a great tip to save money , thanks . I used a tube of plastic worked great but stuck in the bolt. I removed it with a small wood paint brush by sticking it the tube and pulling it out. But, anything small and tube like will work , nice thank you saved money on tools.

I've commented once before but I'm going to comment again. I used your tubing trick tonight and found it to work quite well. I shortened my tube from 1.000 inch to .700 inches and found it worked even easier. You don't have to compress the spring as much while trying to catch the thread. Additionally you can use the threads to compress the spring and reveal the pin for removal. I might also add you don't want to compress the spring any more then necessary to expose and remove the retaining pin. Sure beats shelling out $$$ for the tool.

Well done, great idea. Thank you for sharing this.

Thanks for the video.

You just saved me $40 on a custom jig. Thank you.

Macguyver, and Red Green shed a tear for the simplicity and inginuity. Thank you, sir.

Thank you, sir! This totally worked. That copper tubing was indeed expensive.... too rich for my blood. I ended up using that plastic tube that comes with dog poop bag rolls. Only needed half an inch of it to expose that pin.

It’s been 8 years since this was uploaded, but you deserve a thumbs up for “on my wife’s dining room table” lol 😂

Good job!

Lubricate with grafite powder you will get better performance in cold weather. Grease will slow down firing pin lock time

Man alive you saved my butt! That's using you head. Thank you very much and God bless!

Anyone notice he used the second slot in the back of the bolt to place the penny in? Instead of the first....great video and a brilliant idea.

All most 7 years after you made this video, it's still helping folks out. Well done and thank you.

Saved a bunch of people a bunch of money😄

Grande Mike! Sei il numero 1 Number ONE! Thanks a lot !!!!

That just saved me a bunch of money in tools - thank you!!!

Great video! Thanks for showing us we can do this without spending a lot of money! Much appreciated.

I had the same idea, but I was too afraid I would crush the brass or copper. I was thinking of using a 556 case and cutting and then I had the copper pipe idea but puss’D out

If you go to all the trouble to take off the scrould go ahead and replace that snake spring ,I put a sleeve over my boot made from shrink tubing ,cut five coils off stock spring and replaced it ,,it works fine without binding ,I think I'm going to break down and buy a grey_tan speed lock in the future why in hell Remington put those damned snake like springs in them I'll never know I'd like to tell the nitwit w ho came up with that idea how stupid it was,what was wrong with the old type,,,,,,nothing,,,so they had to change it ?????

Lol @ Wife’s dining room table “I’m telling!!!”

Kudos friend ! Worked like a charm.

Now, do you have to worry about firing pin protusion distance when you change shrouds? I believe factory spec is between .044 and .060. And if so, does your method allow for measuring that? Great idea, thanks for the vid!

Holy shit, I've been all over the place looking for these, you solved it, thanks man.

thanks mate you're a genius. i used 7/8 long of 3/8 fuel line just to let it screw on a few more threads. worked like a charm

Probe the best REM 700 DIY vide I have seen ,,,thanks brother

The man

I used a 38 special casing, I cut the base off and it worked like a charm ...thanks for the great idea!

Excellent video my friend. Thanks

Excellent. I got a new David Tubbs Firing pin and dual spring and wanted to put it in, but I did not have any tubing laying around the apartment. Well, I did have a bunch of .223 empty brass. A couple of quick cuts and a cleanup with sander and bingo. Worked fine! Thanks, you just saved me some cash.

seen this great vid and tried it with a drilled out 380 and so far it works for what I need... Great Idea

Thank you. Your style was adult and very informative. Easy to watch and stay with to the end. Excellent job. I do have a Rem. 700. God is good.

OOh Rahh my friend, God is good all the time.

Thank you for a easy to understand video, I don't have a Remington 700 but I have others and like you do your videos Semper Fi Marine God is Always Good !

Thanks for the video. Very helpful.

Semper Fi Mike G, shoot straight.

what size drillbit did you use for the m10 nutsert and will these work with the factory screws for the flares

Good tip. Thanks

Scott, I always shoot straight. 😉

Good video. Great idea. Took a pipe cutter and cut a .223 case down to about an inch or so, drilled out the flash hole and badda bing. Way cheaper than the brownells kit. Now all I need is a string loop, a penny and a chunk of brass to pull apart the whole assembly. Thanks for the video brother.

After you install the nut zerts you can install your flares easier... bless yer heart!

A.W.E.S.O.M.E. Thanks Bro.