Yeah that would work I just be concerned about Scotch tape aging in the Sun turning yellow

@@Ziyoblader Maybe one of those screen protectors that are also stickers would work?

@@Mochuelo09 yes but you would have to cut it in circles so what I would do is not use a scissor and use a grinder or a Dremel and what I would first do is Trace the inside of the bit chip or wherever you're going to put the glass on so get your first circle ready for it fits nicely and it will probably have sharpie on it so don't use that first circle piece the next piece is going to see your final peace that you're going to put on there so use the existing circle and put it on a new piece of glass and Trace that circle so you get the perfect fit and you're going to grind away where the sharpie traced circle is

I don't see why not if you have them interact like action figures were each figure battles against each other with physical contact it might get scuffed up I would test out the feet of the miniature on the bottom that way you can get a good idea of how rough or durable the coating material is from what I remember when I cooked miniatures with Clay I would use super glue loctite brush on that usually works the best for me make sure you get a fresh one though if you open it up and it's clumpy or slurpee it might not set correctly try to get it to where it's really fresh where you dipped out of water you're going to want to buy a few though after the first few coats on the character surface they do start to dry up the bottles but once they're on they don't yellow up like normal glue they still look clear I have figures that date back to 2008 that don't have any yellow aging

I'm confused why would you want to use 0 g if you wanted a ripcord version for HMS use the 4D ripcord launchers they're more durable in better-performing

The black and red one I believe can be found on eBay it's non-branded which is a fake but it gets the job done the white and blue one was a special release at the beginning of burst in 2015 which will probably be more hard to find your best bet for it would be to look up the takara Tomy product listing and find it that way and then search for it on eBay or Amazon Japan

Thank you it hurts me that I haven't been able to release videos I've been struggling with my health for the past years here energy is drained and I can't eat normal foods anymore mostly soft foods it's been a struggle trying to get to the doctor to figure it out I went to the emergency room this year to do an x-ray and they couldn't figure out what was the cause spent $3,000 for nothing I haven't given up hope though I've been trying to study to get more money with a better paying job now but it's been difficult to balance going to the gym and studying my body's energy is just so low anyways take care and you haven't seen the last of me.

​@@Ziyoblader I hope you can recover soon, just try not to overexert yourself so much, we hope you come back well bro.

It would be a magnetically difficult minefield to play in if your blade was set to negative polarity or you could look on the positive side the first launch you do in the stadium you're instantly attracted to the first hole you come close to

Am8na bile koyar

Nemesisi yenen ona karşı zorlanmaz

The string is not retractable you'll have to wind it up like the old tops it's a piece of string that goes in the center through a shaft every time you pull it you pull the string out of the launcher entirely and then you have to thread it which isn't hard and then wind it up manually and then that cap goes over it

Search up the model name a93 just like in the description of my video on eBay or Yahoo Japan auctions those are your probably best bet to find this set or something similar another site that may have it is rakuten

I don't know the tip wasn't in the best condition for a cyber dragoon by the looks of it but I also didn't check for more balanced weight disk

On ebay many moons ago

What can I say I'm a hard-working welder everyday is another pay for another Bay

@@Ziyoblader damn thats a rough job, good going!

Nope

Yeah I heard the quality control on those fakes are pretty low they're all over the place so you might have gotten one that wasn't up to pair to the TT counterpart like the one I used in the video if you come across an orange one I hear that's better than the yellow loose one I used in the video

I would use super glue but only the super glue brush on as shown in the video put a little bit underneath the sticker and then use a clean metal rod or a knife that is sharp into the point to hold it down

What you might have to do is pour a little pool of super glue and take a toothpick and dab the area you want the sticker to be on or on the sticker itself and use tweezers and then once it's on you can cover over the sticker with super glue and it should preserve it for a long long time unless that spot is exposed to battle but so far for burst I haven't seen that

@@Ziyoblader thanks for the advise my guy Btw I already tried this out but I'm soo dumb why didn't I use a toothpick. it would've been soo much easier 😂

@@Ziyoblader I also used nail polish protector on the chip and stickers and 😲omg it made it look shiny and works really well