Jfc I have my work cut out for me I guess. Glad I didn't put the glovebox back in yet lmao

Im in the middle of pulling a 4l60e from a 99 1500 with a locked up 4.8. i can't get the last tourqe conveter bolt off, and the transmisson will not come off. How did you get the transmission off without the tourqe converter

What are the 2 sizes of hose you had to buy? You said 5/16 but the thicker one but you lost me on the smaller hose. I’m guessing is the same size as the original clear hose so it fits the black hose?

Great video! Whats the trick to get the plugs out to get your hand in there?

Good shit man

Did that fix the leak

What about the passenger side?

Nice video man! Super easy! How did you install the seal though?? Did you just tap all around with the hammer gently or did you use like a big socket to hammer it in evenly?

Thank you for the video it really helped.

Thank you so much!!! I've been recently getting some water on the floorboard and was about to start messing around with the windshield and drains immediate to the sunroof. I just looked where you point us to and saw a disconnect. Other videos don't make it as clear as to where this drain is located. Thanks again.

What is that tool

Thanks my guy!!!!

Mine is leaking coolant on the water pump area, also leaks when I'm trying to fill up the radiator and the car is turned off, I'm guessing the issue is the pump

0:30 why its 10pm at night and im out here looking at caprice courtesy lights 🤣🤣

I had an odd one, carpet was wet even with tube in the boot! I finally figured it out: the water was draining out the boot, but the hood release cable runs right below that angled downward back into the car. The boot for the hood release cable was torn open, so the sunroof water was drawing out into the wheel well, onto the cable, and running down the cable right back into the car, keeping my carpet wet! I covered the torn cable boot, which is right below the drain boot, with silicone sealer. I did this from the outside of the car - had to unscrew and unfasten the wheel well liner to get to these parts.

My 98 honda accord coupe is leaking on the driver side floor board so thx for vid dude

Thanks ! Very helpful !

Great video awesome work

Thank you man! Both of my front drain tubes were just leaking straight down not connected into da boot

Hopefully you can help i have a 2013 ford explorer that when i started in the morning and go to start it again after a hot day it wont crank or start would you happen to know the problem please help

#mechaniclife

Just got mine shit heavy as hell bruh

Is there a list of parts you removed to get the engine out with the torque converter still on the flexplate. Going to try this on a AWD 2010 suburban

Starter is similar build to 70s era GM.

Puttin some work in homie

When I built for lkq they always had us seal the seals with locktite to make sure no leaks occured later down the road good content pimp

Save ya some time and just sell me the motor 😂😂😂😂😂

Been waiting for the update good content pimp keep up the grind

WTF!!! No info and barely a video. Wasn't able to identify anything that I was looking for about REPLACING A STARTER smh

A little more detail. Size of socket needed?Anything else about the plastic piece you were talking about?

How did you pull it out with torque converter still on? In middle doing same

Good video. Very informative. Thanks.

Uncle meme? Is that you

Where did u tie the vacuum lines to?

Use a socket on the harmonic balancer

You ever get other bolt out?

Hell yeah pimp finna be slapping 15s here soon

You did ya thang with box homie..

Get some acid that will eat all that old glue up on the back window trim for the yellow and black two door dont throw it away lil elbow grease and trim a be like new

Yessir bro getting mines done now

Yessir new sub

i mite switch mine to led

You worked my over there 👍🏾

Make a video of install and removal but it not moving at all can be a number of things a seal in low reverse piston could have rolled over frictions burnt up or the input drum snapped in half inside or the sun shell broke

Getting it done 👍🏾

Did u have to cut the hole in ur trunk or was that there

Good look homie. What ever happend to the silver box you had years ago.

You remember the cut out measurements for the Mini Cooper assembly?

you check ebay for the motor? im definitely doing this on my 72 skylark!

Damn i was bput to ask