🙂👍

Strong man

This video is very bad, no explanation as to what he is using to fix the tray to the floor. Additionally and ideally a bed of sand and cement is optimal.

Great advice, drop the music or tame it way down

Throwing it on concrete worked for me. Thanks for the video though!

nice job

Cheers mister for that ..safe driving

ha! Yes, indeed! Throwing agains concrete worked like a charm!!! 2nd try!!

Thanks bro ❤

Thank you

Thank you

Whats the lowbeam bulb type? Thx

Looks like you done a good job , Keep it going

No! Just no...

The music is terrible But thanks for the info !

i wish i could have heard all of your commentary but i couldnt bcz the music is too loud. Thanks so much for video!!

Whats happened to the sensible safety side here? No clamping of workpiece, hands close to blade, no safety glasses? Very poor show

That's a pro

The music is so unnecessary 😂

Good grief you did that on you're own? How long did that take? Good job aswell.

Gosh, where I live no one knows how to do this kind of thing and I wanted to do it myself so bad. This video is a lifesaver, so helpful, thank you so much! Gonna try this on my room ❤

How can I install a bidet on these toitlets?

total bodge

Get rid of the music!!!

ty

Simple and brilliant, thank you for sharing!

Horrid music!!!!!

To remove a broken bit out of the holder simply throw it down on a concrete floor as hard as you can. May take a couple times but will break it loose from magnet. Should give you enough to grab onto. Has worked a number of times for me.

whats the yellow tool you used to flatten the side of the plasterboard?

going to try w a masonry bit...1:40 am....... 1:45 am.......... the tape helps the drill bit to concentrate on the target.....but, only pernitrate 1/10th of an inch... drill and bit both overheating..... its going to take some time :) end of report.. P.S. Ty for sharing yr technic.... :)

You helped me enormously, and saved me paying someone several hundred pounds. Thank you sir. Lovely video btw

Hello what would you do to cover up the white board ? Plaster ? Thank s

The waste outlet will leak this way there is a product out now called drop seal goes straight into the waste and does not leak and it’s watermark too

Why didn't you just turn it around ?

Thank you. 👍🏼

Im about to do same thing, for same reason

This is just watching a joiner do it. It doesnt shows you how as in learning.

I would be interested to know if building regs for your area were complied with. I would have assumed pad stones are needed and the mortar slapped all over the place doesn’t look professional

Thank you very much, you help me so so much.

Bob on mate!

HOLY SHIT!!!! Throw it at concrete like a throwing knife, it pops right out... Thanks everyone for this advice.

How not to do it

Great video! I found that trim on our wood flooring is rotting due to when you clean the floor the liquid gets underneath and soaks into the back of the trim. I've had to take one piece of trim out since the rotting is so bad it's discoloured the trim. If there's not much gap between the floor and skirting I was thinking of just using a white seal like this, do you think that would be ok?

I have a cast iron heavy- heavy toilet from 1896 can't figure out how to connect to the floor???

I think you should have used a concrete drill bit. It grinds instead of cutting. As the square cutting was much faster because you used a grinder.

Throwing the bit against concrete was easy. Took 3 throws and the entire broken bit popped right out.

Awesome job! 🔥🔥🔥

There’s vertical support but no lateral tie the beam to the post. You are trusting the cement/mortar to hold it in place. Be careful

hi thnx for the te video btw . i had a question i have a room about 4 meter high and i wanted to lower it but i dont know with what . what would hold better wood structure or metal strucures for gypsum

My man does not need a ladder! Well done!!!