Brovo this helps so much following and subscribing right now
@JustinLeeMarine13 сағат бұрын
Thank you😊
@mycoolprojectКүн бұрын
I have those same switches on my boat. They do not like water. I replaced a few thinking the the seal was bad, the new ones did the same.
@llewark2Күн бұрын
I had a problem where the generator didn’t start. I bled the line as you demonstrated and that got it started. However, the generator cut out while we were running the boat for several hours. I noticed on the fisher panda website they have a video on bleeding air out but they say to just push the button for 1 to 2 minutes. They do not mention opening the bleed nut. Your video makes more sense. Do you know why they would not mention the need 10mm nut? Also, any thoughts on why mine still cuts out after running awhile.
@JustinLeeMarine22 сағат бұрын
I'm not sure why they would tell you to open the bleed valve. Maybe so people don't open the fuel system and cause more problems. If yours is cutting off after running awhile I would replace the fuel filters and check the fuel lines. Any little restriction causes the fuel pressure to slowly fall. They are very reliant on the fuel pressure being a diesel. If you have too much vacuum in the fuel system it creates air and can cause it to shut down. Keep me posted on what you find. 😊
@lb7wade518Күн бұрын
Hope you replaced that cone washer in the pex fitting!! Just added insurance
@JustinLeeMarineКүн бұрын
That is a great point and I definitely did. I try to make the videos a certain length to not make them too boring. I have them in my van and a bunch of other washers/gaskets. It's a 50 cent part that could cause a serious leak later. Good point. Thank you 😊
@rayjansen6712Күн бұрын
Steadfast as always....👍
@johnschieffelin3226Күн бұрын
Those SureShades can be a real problem. The actuator on a Sure Shade on a boat I bought was faulty, and the seller said trying to get it repaired was a nightmare. No service whatsoever. I ended up removing it from the boat completely. Many boat owners have reported problems with SureShade units.
@JustinLeeMarineКүн бұрын
I can definitely see why 😊
@johnm57142 күн бұрын
Guess we know who’s boat that is LOL⬇ Stuff like this last thing just continues to make me never want options like that. Everything is Awesome-until it craps the bed…and things like that WILL crap the damn bed sooner or later.
@JustinLeeMarine2 күн бұрын
Good customer and job security 😊
@brianroman33902 күн бұрын
Hey, that boat looks really familiar! Thank you for the great content as always. And thank you for all of your work and expertise on this boat! Much appreciated!
@JustinLeeMarine2 күн бұрын
Thank you and you are welcome 😊
@Maxrotor12 күн бұрын
The quality of the old Sea Rays is so much better than the new ones. My 2006 320 uses a metal water tank.
@JustinLeeMarine2 күн бұрын
Manufacturing has definitely changed in the last 20 years.
@LIC1N2 күн бұрын
Good job sir🫡
@jspafford2 күн бұрын
My cantrak display ok button (the one button you need to engage the p ) isn’t working. Display functions but can’t click the button all the way to the right. Emailed domestic 50 times and they won’t respond after the first email. Will never ever have this system in a boat. Never ever ever ever what a pos.
@scottkrute7922 күн бұрын
May I ask if that is a manufacturer specific computer or a multi manufacturer setup. I am looking at the Jaltest
@JustinLeeMarine2 күн бұрын
I use all OEM software because we are a dealership but I have heard of other companies making great software for Marine engines. Keep me posted on what you get. 😊
@kennyGatto-k3p2 күн бұрын
I just found you video yesterday thank you super helpful. I'm running a single outboard and having the same alarm issues is the smart stick easy to install and once installed does it need to be calibrated? Any idea of the part # I need mercury 250L? Thank you
@JustinLeeMarineКүн бұрын
You should not have to do anything if it's just a faulty sensor(smart stick). The part number should be HA5501. Double check this because if it's a pro series steering ram then it has a different part number.
@jamesrahn83393 күн бұрын
There was actually a recall on the shift actuator on the verados. Got a customers changed for free a while ago. Oh and thanks for helping me with a brand new 225 that has this problem.
@boballison1231233 күн бұрын
Great video. Thanks!
@mandih11144 күн бұрын
Happy Birthday young man🎂
@JustinLeeMarine4 күн бұрын
Thank you 😊
@alexbernal49885 күн бұрын
For those with no money to waste. The pump has two thick wires black and red with a fuse. Check for 12v on those. Then the pump has another harness. The one he replaces in this video with 3 wires. Black, purple and white. The purple is +12v and it’s the only one needed to activate the pump. Use a voltimeter or test light to check for power on the purple wire before buying the harness.
@JustinLeeMarine5 күн бұрын
That is correct. Thank you 😊
@raidel881511 сағат бұрын
Thank you for this! I checked the purple wire and it doesn’t have any power, I followed it to the engine and no power either, any idea what it could be?
@alexbernal498810 сағат бұрын
@@raidel8815 The motor has to be running before you test for 12v at the purple wire. Your name makes me think on a Cuban guy. If you are. Ponle un chucho en la pizarra para alimentar la bomba de steering directo a través del cable morado. . De esta manera si tienes un bajo voltage debido a mala batería o alternador puedes apagar la bomba y llegar a casa.
@hansslob67496 күн бұрын
Question: for having vacuum on that tank it needs to be complete closed. For emptying it needs air to get in. How is this done?
@JustinLeeMarine5 күн бұрын
Once you open the cap or the thru hull valve it releases the vacuum. That allows air to enter and the tank to be pumped out. The vacuum pump that pumps it out is stronger than the vacuum that might be in the tank and it draws from the bottom so it removes everything from the tank. Same as the macerator pump that pumps it out of the boat.
@AchikSarih6 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤
@rayjansen67126 күн бұрын
No problem. We all learn by our mistakes... Human.!!
@AchikSarih7 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤
@dj.petesmooth35767 күн бұрын
Happy Birthday Justin
@JustinLeeMarine7 күн бұрын
Thank you. I appreciate that 😊
@robertbeckerjr.78598 күн бұрын
happy birthday Justin!!!!
@JustinLeeMarine8 күн бұрын
Thank you 😊
@jacksett18 күн бұрын
Hey Justin, This happened to me the other day and it locked the starboard engine steering to the left. Is there a way to manual override to get the engine back to center so I can get back to dock with just the sticks and no steering?
@zacharypeters19818 күн бұрын
Justin!! How do I get out the injector dispersion caps that fell into manifolds from pulling injectors Really don't wannna pull apart engines
@JustinLeeMarine8 күн бұрын
That is a tough one. Maybe a small magnet or grabber on a stick camera. It sounds like you will have to pull it apart to get them out. That's never fun. Keep me posted and good luck.
@johnschieffelin32268 күн бұрын
Lotta cool boats in there. The new Aquila 47 center console is an incredible running boat. That old Endeavour catamaran is really homely but they are practical and comfortable. cruising boats.
@JustinLeeMarine8 күн бұрын
It's definitely a cool yard to work at. ☺️
@johnschieffelin32268 күн бұрын
Thanks for the video. Very informative! You have to know so much about every component on a boat. Happy Birthday!
@JustinLeeMarine8 күн бұрын
Thank you. I appreciate that ☺️
@johnm57149 күн бұрын
Multi faceted “Duties” being a marine mechanic. Plumber,electrician,Carpet installer,Carpenter--the list goes on.Have a good birthday Pal…
@JustinLeeMarine8 күн бұрын
Makes the job interesting for sure and thank you ☺️
@Stonehands759 күн бұрын
Awesome as always Happy birthday! Wow heads in a boat I don’t see any of them up here in Nebraska.
@charlesbriggs999 күн бұрын
Happy Birthday!
@A5JDZK9 күн бұрын
Good vid. How's the master Mercury cert going? You're definitely a good Yamaha salesman!!!
@JustinLeeMarine8 күн бұрын
Thank you and it takes some time as I missed the classes this year. Hopefully next year. Still have a bunch of online classes to do. Never ends 😊
@A5JDZK8 күн бұрын
@@JustinLeeMarine Happy birthday
@cruiseducatiify9 күн бұрын
🎂
@jasonworkman46609 күн бұрын
Happy Birthday 🎉
@JustinLeeMarine9 күн бұрын
Thank you 😊
@mgirard71619 күн бұрын
Happy birthday cheers🍻
@JustinLeeMarine9 күн бұрын
Thanks. Much appreciated ☺️
@EverGrowSteve9 күн бұрын
Happy Birthday Justin! 🎂
@JustinLeeMarine9 күн бұрын
Thank you. I appreciate that 😊
@LIC1N9 күн бұрын
Let me your asistent bro
@JustinLeeMarine9 күн бұрын
Come to Marine Max and get a job 😊
@owensmith56129 күн бұрын
Happy birthday love the vids keep up the good work
@JustinLeeMarine9 күн бұрын
Thank you 😊
@bigd5010 күн бұрын
Man, that is a lot of nice boats. Made in China CAN be bad, but frequently that is due to the cost US companies wish to sell the goods at :) iPhones are Made in China and their quality is great. It all depends on the manufacturer, the yard, and the oversight.
@JustinLeeMarine10 күн бұрын
Good point ☺️
@groggman420411 күн бұрын
Hello, can you please give me the number of the pin-out harness so I can test the actuator? Thanks Gregg.
@610boating512 күн бұрын
How many techs work at that yard, wow that's a lot of work orders.
@JustinLeeMarine11 күн бұрын
We have a good amount and it is fortunately needed. We are a very busy yard. ☺️
@Americanboy515012 күн бұрын
Hi Justin thx for videos . Can’t find the one I’m looking for but anyway question ?? I have a 2009 volvo penta 5.0 gxi with dual prop out drive . Trim works fine but when I’m cruising and I operate the trim I’ll get a vibration but I can find a sweet spot where the vibration stops .Also the vibration will start during turns also but not always . I’m gonna pull it out today and look at prop . But do you have any ideas ??
@JustinLeeMarine11 күн бұрын
I would say the common issues with what you are experiencing are U-joint assembly going bad, bent propshaft, or motor alignment. You would have to pull the drive and check the U-joints and check drive alignment. They both can cause odd vibrations. Keep me posted 🙂
@Americanboy515011 күн бұрын
Will do . That’s just what the service Dept said . Say I need gimbal and u joints would you know a round about price I may be charge ?? Parts and labor .I don’t expect you spot on but ruffly ?? Thx for videos !!
@JustinLeeMarine11 күн бұрын
@Americanboy5150 my best guess would be around 4 hours of labor plus parts. Just depends on what they find when they pull stuff apart.
@zacharypeters198112 күн бұрын
God I just redid my heads on my one motor. lol what a fun project. NOT. Now I got dispersing caps from my fuel injectors stuck and fell into intake. Start again!
@pauljohnson868315 күн бұрын
Great video thanks for the tips
@Bear_SJ15 күн бұрын
Thx
@Stonehands7516 күн бұрын
Awesome as always. Was wondering do you spend more time on service calls or in the shop usually?
@JustinLeeMarine16 күн бұрын
90% service calls. I'm one of two that drive around and diagnose problems. Good question and thank you ☺️
@johnm571416 күн бұрын
That Mercury head looked damn scary-one of those things when you are buying used is impossible to see.
@JustinLeeMarine16 күн бұрын
That is true. You never know. Best thing to do is get a good inspection on something used. Compression and leak down will tell you everything. ☺️
@cruiseducatiify16 күн бұрын
Tnx Justin
@BG_Lidar16 күн бұрын
Cool video. That's an insanely big (and busy!) boatyard.
@JustinLeeMarine16 күн бұрын
Thank you 😊
@rayjansen671216 күн бұрын
Really nice boats. Hate to choose ❤
@johnschieffelin322616 күн бұрын
Good video. Amazing how many computers are installed on boats, cars, and everything we use now.